Catler MF 610 User manual

MF 610
Instructions for use
MILK FROTHER
Návod kobsluze
PĚNIČ MLÉKA
Návod na obsluhu
NAPEŇOVAČ MLIEKA
Használati útmutató
TEJHABOSÍTÓ
Instrukcja obsługi
SPIENIACZ DO MLEKA
Инструкции по эксплуатации
МОЛОКОВЗБИВАТЕЛЬ

MILK
FROTHER

3
TABLE OF CONTENTS
TABLE OF CONTENTS
5 Catler recommends safety rst
9 Know your milk frother MF 610
10 Operating your milk frother MF 610
14 Care and cleaning
15 Troubleshooting

4CONGRATULATIONS
Congratulations
on the purchase of your new MF 610 milk frother.

5
CATLER RECOMMENDS SAFETY FIRST
CATLER RECOMMENDS SAFETY FIRST
We understand the importance of safety and that’swhy we put your safety first from the initial
design concept to the production itself. Nevertheless, we ask you to be careful when using
electrical equipment and to observe the following guidelines:
• This appliance may be used by children aged
8years and older, provided they are supervised
or have been instructed in the safe use of
the appliance and understand the potential
dangers.
• User cleaning and maintenance must not be
performed by children unless they are older
than 8 years of age and work under supervision.
• Keep the appliance and its supply out of the
reach of children under 8 years of age.
• This appliance may be used by persons with
physical, sensory, mental impairments or by
inexperienced persons, if they are properly
supervised or have been informed about how
to use of the product in asafe manner and
understand the potential dangers.
• Children must not play with the appliance.
• If the power cord is damaged, ask the
authorised service for areplacement in order
to prevent hazards. It is forbidden to use the
appliance with the power cord damaged.
• This appliance is designed for household use.

6CATLER RECOMMENDS SAFETY FIRST
The appliance is also designed for personal use
in areas such as:
– kitchenettes in stores, offices and other
workplaces;
– agriculture;
– guests in hotels, motels and other dwelling
locations;
– bed and breakfast businesses.
WARNING: Avoid spilling on the plug.
Wash the jug, lid and whisking discs in warm
water with alittle dishwashing liquid. Rinse and
wipe dry. Follow the cleaning instructions in this
manual.
WARNING: Incorrect use may lead to injury.
• The surface of the heating element contains
residual heat after use.
• When cleaning, the appliance must not be
immersed in water.
• The milk jug may only be operated with the
frother base supplied with the jug. Do not use
either the jug or the frother base with other
appliances unless otherwise specified by the
manufacturer.

7
CATLER RECOMMENDS SAFETY FIRST
• This appliance is designed for home use only. This appliance is not designed for
commercial use. Do not use this appliance in moving vehicles or on boats, outdoors, or for
any purpose other than it’sintended. Otherwise, there is arisk of personal injury.
• Before connecting this appliance to apower socket, make sure the voltage stated on the
product'srating label corresponds to the voltage in your power socket.
• Place the appliance on astable, heat-resistant, at and dry surface away from the edge of
the worktop.
• Do not place the appliance on or near heat sources such as hotplates, ovens or gas
burners. Vibrations during operation may cause the appliance to move.
• To prevent electric shock, do not immerse the appliance, the power cord or the power
cord plug in water or other liquid.
• Keep this appliance asafe distance from walls, curtains and other heat or steam sensitive
materials. The recommended distance from these materials is at least 20 cm.
• Do not use this appliance with aprogrammable switch, timer switch or any other device
that automatically switches the appliance on.
• Before switching on the appliance, make sure it is correctly assembled. Make sure the
frothing attachment is properly installed and the lid is properly tted.
• This appliance has been designed for the purpose of frothing milk and other milk
substitutes. Under no circumstances should it be used to heat any other liquids or foods
such as cream, pudding, soup, sauces, etc.
• This appliance is NOT designed for the purpose of stirring large quantities of dry
ingredients or heating large pieces of food such as chocolate chips, ground nuts, spices,
fresh herbs, etc.
• The bottom of the milk jug must ALWAYS be dry before putting it on the frother base and
switching it on.
• Place the lid of the jug properly on the jug before switching on the machine. Never
remove or tamper with the lid during heating. You could get burned by escaping steam.
Do not place any objects on the lid.
• Before replacing the frothing attachment, rst switch o the appliance, disconnect it from
the power supply and wait until it has completely stopped and cooled down.
• Do not touch hot surfaces. Use the handle to manipulate the appliance.
• Take extra care when handling frothed milk in the jug. The milk is hot and you could scald
yourself if you handle it carelessly.
• Do not move the appliance when it is switched on. Do not handle the appliance while it is
on its base and switched on.
• The liquid must always cover at least the“MIN”line, but must not exceed the“MAX”line
to prevent possible burns. If you accidentally switch on the machine without liquid, the
idle protection automatically switches the machine o. Allow the appliance to cool down
before switching it on again.
• Do not insert metal or similar objects that could damage or adversely aect the operation
of the appliance.
• Always ensure that the appliance is switched o and disconnected from the mains socket
before moving, shutting down, cleaning or storing the appliance.
• If you will not be using the appliance for along period of time or if you leave it
unattended, unplug the power cord from the power outlet.
• Allow the appliance to cool down between frothing processes.

8CATLER RECOMMENDS SAFETY FIRST
• Do not remove the jug from the base during operation. If the liquid has reached the
selected temperature, make sure the appliance is switched o before removing the jug
from the base.
• Use only the accessories supplied and recommended by the manufacturer. Otherwise,
there is arisk of are, electrical short circuit or injury.
• Never run the appliance without liquid. There is arisk of damage due to overheating.
• When you have nished using the appliance, always switch it o and disconnect it from
the power supply.
• Check the condition of the appliance regularly. Never use adamaged appliance or an
appliance with adamaged accessory, power cord or plug.
• Do not disconnect the appliance from the power socket by pulling on the power cord. This
could damage the power cord or the power socket. Disconnect the cord from the power
socket by gently pulling the plug of the power cord.
IMPORTANT SAFETY INSTRUCTIONS FOR USING ELECTRICAL EQUIPMENT
• Fully unwind the power cord before use.
• Do not leave the power cord hanging over the edge of atable or countertop or allow it
to touch ahot surface or to become tangled up. Do not put heavy objects on the power
cord.
• For safety reasons, we recommend to connect the appliance in an independent electrical
circuit separated from other appliances. Do not use adapter plugs or extension cords to
connect the appliance to apower outlet.
• To prevent electric shock, do not immerse the appliance, its base or the power cord in
water or other liquids.
• We recommend that you check your appliance regularly. Do not use the appliance if it is
damaged in any way or if the power cord or plug is defective. All repairs or adjustments
must be performed at the nearest Catler authorised service centre.
• Any maintenance other than routine cleaning must be entrusted to an authorised Catler
service centre.
• We recommend to install aresidual current device (standard safety switches in your power
outlet) to provide ahigher level of protection when using the appliance. We recommend
to install aresidual current device (with anominal residual operating current of no more
than 30mA) in the electric circuit in which your appliance is to be connected. For further
expert advise, please contact your electrician.
Instructions are also available at www.catler.eu.
Safety class for electric shock protection:
Class II – Electric shock protection is provided by double or heavy-duty insulation.

9
KNOW YOUR MILK FROTHER MF 610
KNOW YOUR MILK FROTHER MF 610
1
2
3
4
5
6
7
8
1. Jug lid with silicone seal
2. Jug for milk whisking
3. Jug handle
4. Heating element
5. Frother base
6. Control button – used to select the heating method
7. Frothing attachment for milk whisking
8. Frothing attachment for stirring

10 OPERATING YOUR MILK FROTHER MF 610
OPERATING YOUR MILK FROTHER MF 610
BEFORE FIRST USE
Before rst use, remove all packaging
and advertising labels / stickers from the
appliance.
Wash the jug, lid and frothing attachments
in warm water with alittle dishwashing
detergent and wipe dry.
Wipe the outer surface of the base with
asoft, clean cloth lightly soaked in warm
water and wipe dry with aclean, dry cloth.
USING
1. Place the milk frother on adry, at and
rm surface well away from the mains
socket.
2. Insert the selected frothing attachment
onto the shaft located at the bottom of
the jug. Make sure that the attachment is
correctly and rmly positioned.
NOTE:
Always make sure the frothing
attachment is correctly positioned in the
jug before adding liquid.
If the frothing attachment is inserted
incorrectly, it could come loose during
operation of the appliance.
WARNING!
FROTHING AT
TACHMENTS  RISK
OF SUFFOCATION!!
CHILDREN MUST
ALWAYS BE SUPER
VISED TO ENSURE
THEY DO NOT PLAY
WITH THE DEVICE.
3. Pour the required amount of fresh cold
milk into the jug and put the lid on the
jug. Always use fresh cold milk and the
milk level must be between the MIN
and MAX lines for the selected frothing
attachment.
Always observe the MAX line for the
frothing attachment. During the whisking
process, the milk increases in volume and
amilk foam is formed. This could spill
over the edge and damage the frother.
If this happens, immediately remove the
jug from the frother body and disconnect
the power cord from the mains socket.
NOTE:
Never switch on the appliance unless
the minimum amount of liquid in the
jug is reached (the MIN line must be
covered with liquid).
The appliance switches o automatically
if the jug is empty. Wait until the
appliance has cooled down before
switching it on again.

11
OPERATING YOUR MILK FROTHER MF 610
4. Make sure the bottom of the jug is dry
and clean. You can then insert it into the
base of the frother.
5. Insert the power plug into the power
socket.
6. Press the control button repeatedly to
select the heating method in order: Cold
– Latte – Capp – Choco. With each press,
the corresponding indicator light for the
selected heating method will ash.
7. The milk frother will start automatically
after about 2 seconds when the light
of the selected heating method stops
ashing.
NOTE:
Do not remove the jug from the base
during operation. If the heating process
needs to be interrupted, press the
control button once.
8. Once the heating process is complete,
the milk frother automatically switches
o and an audible warning sounds three
times.
9. Carefully remove the jug from the base
as the jug and its contents are very hot.
Always hold the jug by its handle. Never
touch the sides of the jug. Do not place
the hot jug on atable, plastic mats or
heat-sensitive surfaces that may warp or
melt from the heat. We recommend using
heat-resistant wooden cutting boards or
metal pads. Carefully remove the lid and
pour the frothed milk.
NOTE:
The frothing attachment can be very
hot. Wait for it to cool before removing it
from the shaft.
WARNING!
THE WALLS OF
THE JUG ARE VERY
HOT AFTER USE.
NEVER TOUCH THEM
OR PLACE THE JUG
ON HEATSENSITIVE
SURFACES.
WARNING!
UNDER NO
CIRCUMSTANCES
PLACE THE HOT
JUG
ON THE POWER
CORD.
NOTE:
The milk frother has been specially
designed for the purpose of frothing
milk and other milk substitutes. Under
no circumstances should it be used to
heat any other liquids or foods such as
cream, pudding, soup, sauces, etc.
This appliance is NOT designed for the
purpose of stirring large quantities of
dry ingredients or heating large pieces
of food such as chocolate chips, ground
nuts, spices, fresh herbs, etc.

12 OPERATING YOUR MILK FROTHER MF 610
Heating table and use of frothing attachments
Heating
method Number Temper- ature
Heating
time
Frothing at-
tachment
Recommend-
ed use
Capp
(cappuccino)
100 ml (min) 60–70°C 3–4 min
Cappuccino
250 ml (max) 60-65 °C 4–6 min
Latte
100 ml (min) 60–70°C 3–4 min
Latte
250 ml (max) 60-65 °C 4–6 min
Choco (milk
+ chocolate
powder)
100 ml (min) 60–70°C 3–4 min
Hot chocolate
250 ml (max) 60-65 °C 4–6 min
Choco (milk)
100 ml (min) 60–70°C 3–4 min
Hot milk250 ml 60-65 °C 4–5 min
350 ml (max) 60-65 °C 5–6 min
Cold (stirring
cold)
100 ml (min) --- 2 min
Iced coee or
avoured milk
250 ml (max) --- 2 min
NOTE:
The temperatures and heating times are
indicative only. The actual temperature
and heating time depend on several
factors such as the initial temperature of
the milk, the quantity, the type of milk,
etc.

13
OPERATING YOUR MILK FROTHER MF 610
TIPS AND TRICKS
These tips and tricks will help you improve
the results of making frothed milk and your
favourite drinks.
Always use fresh and cold milk (or just
opened).
To achieve the correct frothing results, do
not exceed the MAX line for the milk frothing
attachment inside the jug.
For better results, let the milk warm up alittle
rst before adding the ingredients.
Tap the jug lightly on the table to remove the
bubbles.
Swirl the frothed milk in thejug before
pouring.
Pour the frothed milk all at once to avoid
temperature/consistency breakdown.
Always use aclean jug and frothing
attachments.
When making hot chocolate, use powdered
chocolate. If you are going to use hot
chocolate from achocolate bar, you need
to chop the chocolate into smaller pieces so
that it melts easily and quickly.
The Cold function (stirring cold) is ideal
for preparing cold drinks or dissolving
ingredients. However, do not add powdered
sugar-based ingredients. Frostings or syrups
are most suitable.
IDLE START SYSTEM
The milk frother automatically switches o if
the jug overheats. Overheating of the jug can
occur if the jug is empty, if the inserted liquid
has not reached the MIN line or after aquick
subsequent switch-on.
Wait about 5 minutes for the milk frother to
cool down, or you can rinse the jug with cold
water for faster cooling.
Once the jug is cool enough, you will be able
to turn the appliance back on and continue
frothing.

14 CARE AND CLEANING
CARE AND CLEANING
Before cleaning the appliance, always
disconnect the plug of the power cord from
the mains socket and let it to cool down
properly.
Clean the milk frother after each use to
prevent deposits, unpleasant odours from
dried milk or the formation of unwanted
mould.
WARNING!
DO NOT WASH
THE APPLIANCE,
MAINS CORD AND
PLUG UNDER RUN
NING WATER AND
DO NOT IMMERSE
IT IN WATER OR ANY
OTHER LIQUID.
CAUTION:
DO NOT USE SHARP OBJECTS,
CHEMICALS, THINNERS, PETROL
OR OTHER SIMILAR SUBSTANCES.
UNDER NO CIRCUMSTANCES
SHOULD THE APPLIANCE BE
CLEANED WITH ASTEAM CLEANER.
JUG AND FROTHING ATTACHMENTS
Both the jug and the frothing attachment
will be very hot after use. Wait for the jug and
frothing attachment to cool before rinsing
them under cold water.
Wash the jug, lid and frothing attachment
in warm water with alittle dishwashing
detergent. Rinse in clean water and wipe dry.
The silicone seal of the lid can be removed
and washed separately.
The jug can be washed in the dishwasher
inthe upper basket, but the water
temperature must not exceed 70°C.
FROTHER BASE
Wipe the outer surface with aclean, soft
cloth soaked in lukewarm water. Then wipe
dry.
STORAGE
Before storing, make sure that the appliance
is clean, dry and completely cooled down.
Store it in awell-ventilated dry place out of
reach of children and animals.

15
TROUBLESHOOTING
TROUBLESHOOTING
This chapter describes the most common problems you may encounter while using this
appliance. If your problem is either not stated here or persists, stop using the appliance,
unplug the power cord and contact your authorized service centre.
UNDER NO CONDITION SHOULD YOU REPAIR OR DISASSEMBLE THE APPLIANCE
YOURSELVES. THE APPLIANCE CONTAINS NO USER SERVICEABLE PARTS.
Problem Solution
The milk frother does not heat
the milk.
Make sure the plug is correctly plugged into the mains
socket and you have selected the correct heating
method.
Make sure the jug is correctly inserted in the base.
The frothing attachment does
not rotate during heating.
Make sure that the frothing attachment is correctly
seated on the shaft at the bottom of the jug.
Check that the frothing attachment is not damaged.
The frother does not whisk
enough milk foam.
Use cold and fresh milk.
Check that the milk is not spoiled.
Make sure you use the frothing attachment to froth the
milk.

16
INSTRUCTIONS AND INFORMATION ON DISPOSING OF USED PACKAGING MATERIALS
Dispose of used packaging material at asite designated for waste in your municipality.
DISPOSING OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on products or original documents means that used electric or electronic products must not
be added to ordinary municipal waste. For proper disposal and recycling, take these products to designated
collection points. Or in some European Union states or other European countries the products can be
returned to the local retailer when buying an equivalent new product. Disposing of this product correctly
helps save valuable natural resources and prevents damage to the environment by improper waste disposal.
Ask your local authorities or collection facility for more details. In accordance with national regulations
penalties may be imposed for the incorrect disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic devices, ask your retailer or supplier for the necessary
information.
Disposal in other countries outside the European Union
This symbol is valid in the European Union. If you wish to dispose of this product, request the necessary
information about the correct disposal method from the local council or from your retailer.
This product meets all the basic requirements of the applicable EU directives.
The text, design and technical specifications may be changed without prior notice and we reserve the right to make
these changes.
The original version is in the Czech language.
Manufacturer’saddress: FAST ČR, a.s., USanitasu 1621, Říčany CZ-251 01

17
NOTES