Chamberlain THE ROBO SLIDE User manual

I N S T R U C T I O N M A N U A L
THE ROBO SLIDE
RESIDENTIAL SLIDE GATE OPERATOR
Installation instructions and manual book for
architects, general contractors and dealers
®
®
copyright © 2008 chamberlain professional products - www.liftmaster.com

11
• BEFORE attempting to install, operate or maintain the
operator, you must read and fully understand this manual
and follow all safety instructions.
• DO NOT attempt repair or service of your residential gate
operator unless you are an Authorized Service Technician.
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of serious
injury or death if you do not comply with the warnings that
accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your gate and/or the gate
operator if you do not comply with the cautionary statements that
accompany it. Read them carefully.
IMPORTANT NOTE
SPECIFICATIONS AND WARNINGS
Specifications and Warnings . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Installation Information . . . . . . . . . . . . . . . . . . . . . . . 3
Suggested Entrapment Protection Device Locations . . . . .4-5
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Warning Sign Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety Catch Rollers and Gate Rail Stops . . . . . . . . . . . . . . . 7
INSTALLATION
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mounting Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chain Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Earth Ground Rod Installation . . . . . . . . . . . . . . . . . . . . . . . 9
WIRING
Control Board Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Surge Suppressor Terminal Connections . . . . . . . . . . . . . . 11
DC Power Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Solar Panel Connection - Optional . . . . . . . . . . . . . . . . . . . 13
Fire Release Box - Optional. . . . . . . . . . . . . . . . . . . . . . . . . 14
Input Board - Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Solenoid/Maglock Connection . . . . . . . . . . . . . . . . . . . . . . 16
12 VDC Photo Beam Wiring - Optional . . . . . . . . . . . . . . . . 17
Optional Edge Sensor Wiring - Optional . . . . . . . . . . . . . . . 18
3-Button Control Station Wiring Connection . . . . . . . . . . . 19
3-Button Control Station Wiring Master/Secondary . . . . . . 20
Single Operator Loop Size and Placement . . . . . . . . . . . . . 21
Master/Secondary Loop Size and Placement . . . . . . . . . . . 22
12 VDC External Loop Detector Wiring. . . . . . . . . . . . . . . . 23
ADJUSTMENTS
Gate Movement Direction . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Limit Switch Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setting Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Master and Secondary with Timer . . . . . . . . . . . . . . . . . . . 26
Master and Secondary without Timer . . . . . . . . . . . . . . . . . 27
315 MHz Radio Receiver Programming . . . . . . . . . . . . .28-29
Two-Way Adjustable Reversing Sensor . . . . . . . . . . . . . . . 30
OPERATION AND MAINTENANCE
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 31
LED Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-33
How to Reset the Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . 34
How to Check the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Mechanical
Electrical
TABLE OF CONTENTS
WARNING
WARNING
CAUTION
TROUBLESHOOTING
The Gate Will Not Close . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
The Gate Will Not Open . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
If You Hear a Beep Sound . . . . . . . . . . . . . . . . . . . . . . . . . 36
REPAIR PARTS
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Robo Slide Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
How to Order Repair Parts . . . . . . . . . . . . . . . . . . . . . . . . . 39
INSTALLATION CHECKLIST. . . . . . . . . . . . . . . . . . . . 40

2
SPECIFICATIONS AND WARNINGS
Recommended Gate Setup Configuration
Gate Speed – 11 inch per second
Maximum Gate Length – 20 feet
Maximum Gate Weight – 800 pounds
Maximum Cycles – 70 cycles per day with Chamberlain Elite’s Plug-In Transformer.
–Solar power cycles per day varies, Contact Chamberlain for more Information
–Battery back-up cycles (50 cycles total)
AC Power Supply – 25 VDC 1.6 Amp Plug-In Transformer (Part # A POW-1)
AC Power Supply Wire – 14 gauge or greater landscape lighting cable rated for direct burial and 300 watts at
maximum length of 1000 ft.
DC Power Supply – Built-in, back-up for AC or Solar power failure only
Solar Power – Optional (Part # SOLAR 3)
Non-Pinch
Rollers
Sensor Edges
Sensor
Edges
Non-Pinch
Rollers
3" Max. Width
(2"x 2" Screen)
Weld Physical Stops on
Both Ends of Gate Rail
All “Pinch Points” MUST have protective safety devices.
Warning Placards
Permanently Mounted
on Both Sides
of Gate
SPECIFICATIONS

SAFETY INSTALLATION INFORMATION
33
1. Install the gate operator only when:
a. The operator is appropriate for the construction and the usage class of the gate.
b. All openings of a horizontal swing gate are guarded or screened from the bottom of the gate to a minimum of
4' (1.2 m) above the ground to prevent a 2-1/4" (6 cm) diameter sphere from passing through the openings anywhere in the
gate, and in that portion of the adjacent fence that the gate covers in the open position.
c. All exposed pinch points are eliminated or guarded, and guarding is supplied for exposed rollers.
2. The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate
access opening.
3. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when
opening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas.
4. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator.
5. Controls must be far enough from the gate so that the user is prevented from coming in contact with the gate while operating
the controls.
6. Controls intended to be used to reset an operator after 2 sequential activations of the entrapment protection device or devices
must be located in the line of sight of the gate, or easily accessible controls shall have a security feature to prevent unauthorized
use.
7. All warning signs must be installed where visible, on each side of the gate.
8. For a gate operator utilizing a non-contact sensor:
a. Reference owner’s manual regarding placement of non-contact sensor for each type of application.
b. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is
still moving.
c. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter
reachable by a moving gate or barrier.
9. For a gate operator utilizing a contact sensor such as an edge sensor:
a. A hard wired contact sensor shall be located and its wiring arranged so the communication between the sensor and the gate
operator is not subject to mechanical damage.
b. A wireless contact sensor such as the one that transmits radio frequency (RF) signals to the gate operator for entrapment
protection functions shall be located where the transmission of the signals are not obstructed or impeded by building
structures, natural landscaping or similar obstruction. A wireless contact sensor shall function under the intended end-use
conditions.
c. One or more contact sensors shall be located at the leading edge, trailing edge and post mounted both inside and outside of a
vehicular horizontal slide gate.
d. One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate.
e. One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the bottom
edge of a swing gate is greater than 6" (15 cm) above the ground at any point in its arc of travel, one or more contact sensors
shall be located on the bottom edge.

44
Outside Safety
Loop
Inside Safety
Loop
Outside Property
Inside Property
Outside Safety
Loop
Out
O
O
Out
Entrapment Danger
for OPEN Cycle
utside Safety
Loop
de S
Outs
O
O
uts
uts
O
O
O
O
O
O
Inside Safety
Loop
Outside Property
Inside Property
Safety Danger
for CLOSE Cycle
SUGGESTED ENTRAPMENT PROTECTION DEVICE LOCATIONS
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.
WARNING
Install photo electric sensors to protect against any entrapment
or safety conditions encountered in your gate application.
See page 17.
Safety loops allows the gate to stay open
when vehicles are obstructing the gate path.
Suggested for vehicles 14 feet or longer.
See pages 21 and 22.
Gate Rail Stops For safety
reasons, physical stops MUST
be installed on both ends of
the gate rail prior to installation
of the gate operator. This will
assure that the gate does not
derail while opening or closing
fully.
See page 7.
Non-Contact Sensors (Photo Electric Sensors)

5
Outside Safety
Loop
Inside Safety
Loop
Outside Property
Inside Property
Outs
O
O
uts
O
O
O
Entrapment Danger
Safety Danger
SUGGESTED ENTRAPMENT PROTECTION DEVICE LOCATIONS
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.
WARNING
Install edge sensors to protect against any entrapment or
safety conditions encountered in your gate application.
See page 18.
Safety loops allows the gate to stay open
when vehicles are obstructing the gate path.
Suggested for vehicles 14 feet or longer.
See pages 21 and 22.
Gate Rail Stops
For safety
reasons, physical
stops MUST be
installed on both
ends of the gate
rail prior to
installation of the
gate operator.
This will assure
that the gate does
not derail while
opening or
closing fully.
See page 7.
Edge sensor for open cycle on wall.
Edge sensor for open cycle on wall.
Edge sensor
for close cycle
on gate.
Edge sensor for
close cycle on wall.
Edge sensor for open cycle on gate.
Contact Sensors (Edge Sensors)

To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.
WARNING
SAFETY PRECAUTIONS
Property owners MUST never mount any
gate operating device near the gate’s path!
Property owners MUST never allow
anyone to hang or ride on the gate!
Property owners MUST never let pedestrians
cross the path of a moving gate!
WARNING SIGN PLACEMENT
THE ROBO SLIDE IS FOR USE ON VEHICULAR PASSAGE GATES ONLY
AND NOT INTENDED FOR USE ON PEDESTRIAN PASSAGE GATES.
To prevent SERIOUS INJURY or DEATH from a moving gate:
Install Warning signs on BOTH sides of EACH gate in PLAIN VIEW.
WARNING
6

77
Closing Gate
Closing Gate
Because the coasting distance may
vary due to changes in temperature,
it is NOT recommended to install a
stop or catch post in front of the
gates path. To do so will cause the
gate to hit the post in certain
instances.
It is only recommended to install catch
rollers with safety covers on the side of a
post or wall with a minimal distance of half
an inch between the rollers and gate.
NOTE: For safety reasons, physical stops MUST be installed on both ends of the gate
rail prior to installation of the gate operator. This will assure that the gate does not
derail while opening or closing fully.
When fully opened, the end of the sliding gate should
stop at least five inches from an obstructing wall.
End View of Gate and Wall
SAFETY CATCH ROLLERS AND GATE RAIL STOPS
5"
1/2"1/2"
Gate Rail Stop
DO NOT use a
Gate Catch Post.

8
6"
20"
15"
10"
8"
ACCESSSYSTEMS INC
ACCESSSYSTEMS INC
OVERLOAD
POWER
CHARGEOK
BATTERYLOW
OPENRELAY
CLOSERELAY
TIMER
UP
ON
W1
OFF
OPENTORIGHT
60 0
PW
CENTRALCONTROL
SYSTEMON
DCOPERATORv 5M
MADEINUSA
ALARM
SENSOR
REVERSE
SENSOR
HEAVY
GATE
FIRE
DEPT
STRIKE
OPEN
SAFETY
LOOP
EXIT
LOOP
RADIO
REC
CHARGING
POWER
BOARD
POWER
CHECK
FUSE
J2
POWERINPUT
18VAC
SAFETY
LOOP
EXIT
LOOP
FIREDEPT
KEYSWITCH
STRIKEOPEN
PUSHBUTTON
RADIO
RECEIVER
CLASS2
SUPPLY
MOUNTING OPERATOR
CHAIN INSTALLATION
Incorrect Chain Installation
Too High
Too Low
Gate
Incorrect Chain Spacing
4" Minimum
Gate
Correct Chain Spacing
Front of GateBack of Gate
POWERINPUT
18VAC
SAFETY
LOOP
EXIT
LOOP
FIREDEPT
KEYSWITCH
STRIKEOPEN
PUSHBUTTON
RADIO
RECEIVER
CLASS2
SUPPLY
eliteaccess.com
®
ACCESSSYSTEMSINCACCESSSYSTEMS INC
ROBOSURGE SUPPRESSOR
POWERINPUT
18VAC
SAFETY
LOOP
EXIT
LOOP
FIREDEPT
KEYSWITCH
STRIKEOPEN
PUSHBUTTON
RADIO
RECEIVER
CLASS2
SUPPLY
eliteaccess.com
®
ACCESSSYSTEMSINCACCESSSYSTEMS INC
ROBOSURGE SUPPRESSOR
Minimum space between gate and output sprocket must be 4". After you position the gate operator, bolt-down the operator to the concrete bed.
Make certain that the concrete bed is solid.
Correct Chain Installation
Installation
GETTING STARTED
This gate operator is designed for single home application, or for limited commercial applications. An example of a commercial
application would be a factory facility with limited cycles per day, using a plug in transformer or solar panel.
4 Concrete Anchors
1/2" x 3 1/2"
Below the frost line.
Check all local codes.
UL approved underground conduit(s).
High voltage power wires run in
separate conduit.
Above
Ground

9
OVERLOAD
POWER
CHARGEOK
BATTERYLOW
OPENRELAY
CLOSERELAY
TIMER
UP
ON
W1
OFF
OPENTORIGHT
60 0
PW
CENTRALCONTROL
SYSTEMON
DCOPERATORv5M
MADEINUSA
ALARM
SENSOR
REVERSE
SENSOR
HEAVY
GATE
FIRE
DEPT
STRIKE
OPEN
SAFETY
LOOP
EXIT
LOOP
RADIO
REC
CHARGING
POWER
BOARD
POWER
CHECK
FUSE
J2
POWERINPUT
18VAC
SAFETY
LOOP
EXIT
LOOP
FIREDEPT
KEYSWITCH
STRIKEOPEN
PUSHBUTTON
RADIO
RECEIVER
CLASS2
SUPPLY
EARTH GROUND ROD INSTALLATION
Use 14 gauge / 300 watt direct burial, landscape lighting wire
NOT to exceed 1000 ft. for transformer.
Wiring
To reduce the risk of SEVERE INJURY or DEATH:
• ANY maintenance to the operator or in the area near the
operator MUST not be performed until disconnecting the
electrical power and locking-out the power via the operator
power switch. Upon completion of maintenance the area
MUST be cleared and secured, at that time the unit may be
returned to service.
• Disconnect battery and 25 Vdc transformer or solar panel
BEFORE proceeding. Operator MUST be properly grounded
and connected in accordance with local electrical codes.
NOTE: The operator should be on a separate fused line of
adequate capacity.
• ALL electrical connections MUST be made by a qualified
individual.
• DO NOT install any wiring or attempt to run the operator
without consulting the wiring diagram. We recommend that
you install an optional reversing edge BEFORE proceeding
with the control station installation.
• ALL power wiring should be on a dedicated circuit and well
protected. The location of the power disconnect should be
visible and clearly labeled.
• ALL power and control wiring MUST be run in separate
conduit.
• BEFORE installing power wiring or control stations be sure to
follow all specifications and warnings described below.
Failure to do so may result in SEVERE INJURY to persons
and/or damage to operator.
WARNING
All power wiring should be on a dedicated circuit and well protected.
NOTE: Calculated using NEC guidelines. Local codes and conditions must be reviewed for suitability of wire installation.
To prevent SERIOUS INJURY or DEATH from a moving gate:
DO NOT disconnect the built-in audio alarm or reset switch.
WARNING
To AVOID damaging gas, power, or other underground utility
lines, contact underground utility locating companies BEFORE
digging more than 18" (46 cm) deep.
To AVOID damaging 25 Vdc plug-in transformer, it MUST be
enclosed in a suitable weatherproof enclosure and provided
with proper weatherproof fixtures.
CAUTION
CAUTION
Proper grounding gives an electrical charge, such as from an
electrical static discharge or a near lightning strike, a path from
which to dissipate its energy safely into the earth.
Without this path, the intense energy generated by lightning could
be directed towards the Elite gate operator. Although nothing can
absorb the tremendous power of a direct lightning strike, proper
grounding can protect the gate operator in most cases.
The earth ground rod must be located within 3 feet from the Elite
gate operator. Use the proper type earth ground rod for your
local area.
The ground wire must be a single, whole piece of wire. Never
splice two wires for the ground wire. If you should cut the ground
wire too short, break it, or destroy its integrity, replace it with a
single wire length.
Single Piece of
12 gauge wire
Check local codes for
proper depth
Within 3 ft

1010
OVERLOAD
POWER
BATTERY LOW
OPEN RELAY
CLOSE RELAY
TIMER
UP
ON
W1
OFF
OPEN TO RIGHT
60 0
PW
CENTRAL CONTROL
SYSTEM ON
DC OPERATOR v 5M
MADE IN USA
ALARM
SENSOR
REVERSE
SENSOR
HEAVY
GATE
FIRE
DEPT
STRIKE
OPEN
SAFETY
LOOP
EXIT
LOOP
RADIO
REC
CHARGING
POWER
BOARD
POWER
CHECK
FUSE
J2
CHARGE OK
1
2
3 Low Battery Indicator LED
4 Heavy Gate Indicator LED
5 Open Relay LED
6 Close Relay LED
7 System on, Reversing Sensor and Alarm Sensor
8 Alarm Sensor LED
9 Reversing Sensor LED (Rebounder)
1010 Central Control LED
1111 Fire Department or Key Switch LED
1212 Strike Open LED
1313 Safety Loop or Photocell LED
1414 Exit Loop LED
1515 Radio Receiver LED
16
17
1818 J2 Alternate Optional Output
1919 Movement Direction Sockets
2020 Replace Fuse Indicator
2121 Spike Suppressor
2222 Jumper for Stop Button
2323 Optional Input Board
2424 Surge Suppressor Connector
2525 Breaker Reset
2626 Overload LED
2727 On Board Open Button
2828 On Board Stop Button
2929 On Board Close Button
1515
1414
1313
1212
1111
4
9
2323
8
7
1818
2424
2121
22221919
2020
1
2626
2
3
5
6
2525
OPEN
CLOSE STOP
1717
1616
1010
2727
2828
2929
CONTROL BOARD FUNCTIONS
To AVOID damaging the control board, replace fuses ONLY
with same type and rating specified above.
CAUTION

®
STRIKE OPEN
PUSH BUTTON
STRIKE OPEN
PUSH BUTTON
FIRE DEPT
KEY SWITCH
FIRE DEPT
KEY SWITCH
CLASS 2
SUPPLY
CLASS 2
SUPPLY
SAFETY
LOOP
SAFETY
LOOP
POWER INPUT
25 VDC
RADIO
RECEIVER
RADIO
RECEIVER
EXIT
LOOP
EXIT
LOOP
–– ++
P/N Q412
PATENT PENDING
P/N Q412
PATENT PENDING
ROBO SURGE SUPPRESSOR
®
ACCESS SYSTEMS INCACCESS SYSTEMS INCACC E S S SY S T E M S IN C
71312111098
1 654
––
–
DC DC
4
78
0
HELP
9
123
56
7
10
9
10
9
10
9
8
12 Volt
Neg.
Com.
Neg.
++
––
––
13
12
11
11
1 Red
2 Black
4 Green
3 White
®
11
13
––
++
4
3
13
11
6
5
13
11
13
11
4
3
Card Reader
Remote NOT Provided
External 12 VDC “Exit” Loop Detector
12 VDC Photo Electric Sensor (Safety)
External 12 VDC “Safety” Loop Detector
Master/Second Operator Link
315 MHz Factory Installed
Radio Receiver
Push Button
Telephone Entry System
Fire or any Key Switch
NOTE: Terminals 11 and 12 are the ONLY terminals that will
Open and Close with a single push of a button. All other
terminals will ONLY open with a single push of a button.
Dry Contact
Dry Contact
Page 23
Page 23
Page 17
Output Power
Ground
12 VDC
Remote Programming on pages 28 and 29.
Power
Power
Power
Separate power
for card reader.
Separate power
for second operator.
Separate power
for TES.
To ENSURE proper operation of external devices:
• ENSURE bare wires make good contact inside
removable terminal connections.
• DO NOT let wire insulation interfere with connection.
CAUTION
SURGE SUPPRESSOR TERMINAL CONNECTIONS
11

12
Do not use solar panel and plug-in transformer at the same time.
Use Chamberlain Elite’s optional 25 VDC plug-in transformer
(APOW1). Hook up the transformer to 120 VAC. Use two,
low voltage, 14 gauge / 300watt direct burial, landscape lighting
cables. Hook these wires to the plug-in transformer and to the
power input connection on the surge suppressor. Polarity does
not matter.
25 VDC
Plug-in
Transformer
Use 14 gauge / 300 watt direct burial, landscape lighting
wire NOT to exceed 1000 ft. for transformer.
Polarity Does Not Matter
To 120 VAC
®
STRIKE OPEN
PUSH BUTTON
STRIKE OPEN
PUSH BUTTON
FIRE DEPT
KEY SWITCH
FIRE DEPT
KEY SWITCH
CLASS 2
SUPPLY
SAFETY
LOOP
SAFETY
LOOP
POWER INPUT
25 VDC
RADIO
RECEIVER
RADIO
RECEIVER
EXIT
LOOP
EXIT
LOOP
–– ++
P/N Q412
PATENT PENDING
P/N Q412
PATENT PENDING
ROBO SURGE SUPPRESSOR
®
ACCESS SYSTEMS INCACCESS SYSTEMS INC
ACCESS SYSTEMS INC
71312111098
1 654
––
–
DC DC
®
POWER INPUT
25 VDC
®
ACCESS SYSTEMS INCACCESS SYSTEMS INCACCESS SYSTEMS INC
–
DC DC
LOW
LOW
VOLTAGE
VOLTAGE
ONLY!
ONLY!
When the plug-in transformer has been connected to the power source, connect the battery cable plug to the motor harness plug. You
will hear 3 beeps. After the beeps, check the “Charge OK” LED...it must be “ON”.
Beep!
Beep!
Beep!
Motor Harness
OVERLOAD
POWER
BATTERY LOW
OPEN RELAY
CLOSE RELAY
TIMER
UP
ON
OFF
60 0
PW
CENTRAL CONTROL
SYSTEM ON
DC OPERATOR v 5M
MADE IN USA
ALARM
SENSOR
REVERSE
SENSOR
HEAVY
GATE
FIRE
DEPT
STRIKE
OPEN
SAFETY
LOOP
EXIT
LOOP
RADIO
REC
CHARGING
POWER
BOARD
POWER
CHECK
FUSE
J2
CHARGE OK
CHARGE OK
OPEN
CLOSE STOP
Alarm Sensor LED will flash 3 times
during power connection. This
means the board is OK.
DC POWER CONNECTION
To AVOID damaging 25 Vdc plug-in transformer, it MUST be
enclosed in a suitable weatherproof enclosure and provided
with proper weatherproof fixtures.
To AVOID damaging control board, DO NOT use the solar panel
and the plug-in transformer at the same time.
CAUTION
Earth Ground Rod Highly Recommended!

13
Polarity Does
Not Matter
Solar Panel
(SOLAR3)
No Stand
30 AHr
12 VDC
®
STRIKE OPEN
PUSH BUTTON
STRIKE OPEN
PUSH BUTTON
FIRE DEPT
KEY SWITCH
FIRE DEPT
KEY SWITCH
CLASS 2
SUPPLY
CLASS 2
SUPPLY
SAFETY
LOOP
SAFETY
LOOP
POWER INPUT
25 VDC
RADIO
RECEIVER
RADIO
RECEIVER
EXIT
LOOP
EXIT
LOOP
–– ++
P/N Q412
PATENT PENDING
P/N Q412
PATENT PENDING
ROBO SURGE SUPPRESSOR
®
ACCESS SYSTEMS INCACCESS SYSTEMS INC
ACC E S S SYST E M S INC
7 1312111098
1 654
––
–
DC DC
®
POWER INPUT
25 VDC
®
ACCESS SYSTEMS INCACCESS SYSTEMS INCAC C E S S SY S T E M S I N C
–
DC DC
OPTIONAL SOLAR PANEL CONNECTION
To AVOID damaging 25 Vdc plug-in transformer, it MUST be
enclosed in a suitable weatherproof enclosure and provided
with proper weatherproof fixtures.
To AVOID damaging control board, DO NOT use the solar panel
and the plug-in transformer at the same time.
CAUTION
Chamberlain Elite recommends using a larger battery
(12 VDC, 30 AHr) (Part # A12330SGLPK) in this operator when
using the optional solar panel.
CAUTION
If you use Chamberlain Elite’s optional solar panel (Solar3).
Connect the two wires from the solar panel to the power input
connection on the surge suppressor (Polarity does not matter).
Sunlight will energize the batteries through the solar panel. This
solar panel will charge up to 1000 Mamp/Hr in optimum
conditions & 300 Mamp/Hr in light overcast conditions. For
further details about Chamberlain Elite’s solar panel, consult the
“Solar 3” Installation sheet that is included with the solar panel.
Do not use solar panel and plug-in transformer at the same time.
Energizing this operator with solar power only needs the radio
receiver to operate the gate. The only recommended external
devices other than radio receivers are dry-contact command
devices which do not consume any current like key switches.
Using other devices that consume high current such as
telephone access, magnetic locks or loop detectors will cause
excess drainage of the battery and eventually completely
drain the battery.
For more details, contact your local dealer.

14
The chain is held in place by a spring loaded pin.
Pull firmly on the
“T” Handle to release
the chain.
The “Fire Release Box”, is designed for use on sliding gates. It consists of a plated box, with doors on the front and back. The doors
can be locked with your own padlock, or the fire department’s padlock. The fire box would be fixed to the gate pickets. It can be
opened from either side of the gate. A steel cable with a T-handle runs from the box to the release mechanism at the rear end of the
chain. We do not provide the 1/2" EMT to run the cable through. The release mechanism, is placed where the chain bolt would
normally be. When you pull on the T-handle, you release the chain from the bolt. To reset, simply reinsert the pin into the housing for
normal operation (Part # ACP17).
Contact your local dealer
for more information.
“OPTIONAL” FIRE RELEASE BOX

15
OVERLOAD
POWER
BATTERY LOW
OPEN RELAY
CLOSE RELAY
CENTRAL CONTROL
SYSTEM ON
DC OPERATOR v 5M
MADE IN USA
ALARM
SENSOR
REVERSE
SENSOR
HEAVY
GATE
FIRE
DEPT
CHARGING
POWER
BOARD
POWER
CHECK
FUSE
J2
CHARGE OK
The optional board allows extra control of the gate, is available only from Chamberlain Elite Access Systems. Installation is simple;
just clip the optional board to the J2 slot on the top of the control board. Below lists the function of each pin.
16
2 4 6 8 10
12
14
15
13
11
9
7
5
3
1
16-Pin Plug
OPEN
Open Switch (N.O.)
Stop Switch (N.C.) (Cut W1 Jumper at Bottom of Board)
Timer Close Output to Slave
Timer Input from Master (Close Command or Close Switch) (N.O.)
Alarm Output will be set off with very heavy gates or object preventing gate operation.
(Not Burglar Alarm) (9 = +12 VDC, 10 = Alarm)
Emergency Open Switch (Direct Command from Battery to Motor)
Emergency Close Switch (Direct Command from Battery to Motor)
Magnetic Lock - Dry Contact Relay (13 = Com, 14 = N.C.)
Center Loop Option (For Swing Gate Operators Only)
1
& 2
3 & 4
5
& 6
7 & 8
9 & 10
d
11 & 4
12 & 7
13 & 14
15 & 16
W1
“OPTIONAL” INPUT BOARD

16
OVERLOAD
POWER
BATTERY LOW
OPEN RELAY
CLOSE RELAY
CENTRAL CONTROL
SYSTEM ON
DC OPERATOR v 5M
MADE IN USA
ALARM
SENSOR
REVERSE
SENSOR
HEAVY
GATE
CHARGING
POWER
BOARD
POWER
CHECK
FUSE
J2
CHARGE OK
The “Optional” input board MUST be used to perform this
function (Part# Q203 ).
16
2 4 6 8 10
12
14
15
13
11
9
7
5
3
1
N.C. Power
for
Maglock
Common
Part # A MG 1300
13
14
16-Pin Plug
Dry Contact Relay
Relay Contact Rating
0.5 Amp - 125 VAC
1 Amp - 24 VDC
SOLENOID/MAGLOCK CONNECTION
To ENSURE proper operation of external devices:
• ENSURE bare wires make good contact inside removable
terminal connections.
• DO NOT let wire insulation interfere with connection.
CAUTION

17
®
STRIKE OPEN
PUSH BUTTON
STRIKE OPEN
PUSH BUTTON
FIRE DEPT
KEY SWITCH
FIRE DEPT
KEY SWITCH
CLASS 2
SUPPLY
CLASS 2
SUPPLY
SAFETY
LOOP
SAFETY
LOOP
POWER INPUT
25 VDC
RADIO
RECEIVER
RADIO
RECEIVER
EXIT
LOOP
EXIT
LOOP
–– ++
P/N Q412
PATENT PENDING
P/N Q412
PATENT PENDING
ROBO SURGE SUPPRESSOR
®
ACCESS SYSTEMS INCACCESS SYSTEMS INCACCESS SYSTEMS INC
7 1312111098
1 654
––
–
DC DC
11 13
– +
1 4
Power
(Part # A OMRON 12V) (Failsafe)
Contact your local dealer
for more information.
Photo Beam (Safety) 12 VDC
BlueOrange White Brown
It is best to use 12 VDC Failsafe Photo Beam Sensors for this Safety Option
Failsafe Photo Beam: If a failsafe photo beam is not working or loses power or photo beam is blocked, then the
photo beam will stop all gate operation.
NOTE: If photo beam is blocked the gate will stop
and reopen. The gate will remain open until the
obstruction is cleared.
“OPTIONAL” 12 VDC PHOTO BEAM WIRING
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Locate entrapment protection devices to protect in BOTH the
open and close gate cycles.
• Locate entrapment protection devices to protect between
moving gate and RIGID objects, such as posts or walls.
WARNING

18
OPTIONAL EDGE SENSOR WIRING
®
STRIKE OPEN
PUSH BUTTON
STRIKE OPEN
PUSH BUTTON
FIRE DEPT
KEY SWITCH
FIRE DEPT
KEY SWITCH
CLASS 2
SUPPLY
CLASS 2
SUPPLY
SAFETY
LOOP
SAFETY
LOOP
POWER INPUT
25 VDC
RADIO
RECEIVER
RADIO
RECEIVER
EXIT
LOOP
EXIT
LOOP
–– ++
P/N Q412
PATENT PENDING
P/N Q412
PATENT PENDING
ROBO SURGE SUPPRESSOR
®
ACCESS SYSTEMS INCACCESS SYSTEMS INCACCESS SYSTEMSINC
7 1312111098
1 654
––
–
DC DC
Miller Edge Models: MGR20 or MGS20
• Never Paint Sensing Edge
• Never Pull On Wires
• Never Cut or Puncture Edge
• Never Operate Unguarded Equipment
1 4
Contact your local dealer
for more information.
To prevent SERIOUS INJURY or DEATH from a moving gate:
• Locate entrapment protection devices to protect in BOTH the open and close gate cycles.
• Locate entrapment protection devices to protect between moving gate and RIGID objects, such as posts or walls.
WARNING
NOTE: When touched, these electrically activated edge sensors immediately signal the gate operator to stop and reverse. Property
owners are obligated to test edges monthly. See page 37 for edge sensor part numbers.

19
IMPORTANT NOTE: The “Optional” input board (Q203) must be
used to perform this function.
Cut W1 jumper at the bottom of Board
to use the stop button in the 3-button
control station.
16
2 4
6
8
10
12
14
15
13
11
9
7
5
3
1
N.C.
W1
1
2
4
8 7
3
16-Pin Plug
OVERLOAD
POWER
BATTERY LOW
OPEN RELAY
CLOSE RELAY
TIMER
UP
ON
W1
OFF
OPEN TO RIGHT
60 0
PW
CENTRAL CONTROL
SYSTEM ON
DC OPERATOR v 5M
MADE IN USA
ALARM
SENSOR
REVERSE
SENSOR
HEAVY
GATE
FIRE
DEPT
STRIKE
OPEN
SAFETY
LOOP
EXIT
LOOP
RADIO
REC
CHARGING
POWER
BOARD
POWER
CHECK
FUSE
J2
CHARGE OK
OPEN
CLOSE STOP
There can be NO common wires within this
3-button control station.
Open-N.O. Contact
Stop-N.C. Contact
Close-N.O. Contact
3-BUTTON CONTROL STATION WIRING CONNECTION
To ENSURE proper operation of external devices:
• ENSURE bare wires make good contact inside removable
terminal connections.
• DO NOT let wire insulation interfere with connection.
CAUTION