Charge Amps Halo Pole Mount User manual

Charge Amps Halo Pole Mount
Installation manual

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
2
Table of Contents
Greetings installer! ........................................................................................ 3
About Halo Pole Mount ................................................................................. 3
Contents of the package ................................................................................. 3
Provided by the installer .................................................................................. 4
Before installation ......................................................................................... 4
Tools .................................................................................................................. 4
Installing the Halo Pole Mount ...................................................................... 4
Installing the Halo ......................................................................................... 13
Rights ............................................................................................................ 14

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
3
Greetings installer!
This installation manual is intended for qualified Halo Pole Mount installers and describes
how to install the product safely and properly.
Installation may only be carried out by a qualified installer who follows:
•Basic safety precautions for safe and correct installation.
•Local, regional and national installation regulations.
•The instructions in this Halo Pole Mount installation manual.
About Halo Pole Mount
Halo Pole Mount expands your mounting options and allows you to place your charging
station on a standard pipe of 60 millimeters. Maximum allowed diameter of the post is
61.0 millimeters.
Contact your supplier for more information about your specific Halo Pole Mount.
Contents of the package
•Halo Pole Mount
•Installation kit, zip-lock bag containing 3 pcs M6 x 12, 1 pcs M5 x 8, 1 pcs tooth
washer M5, 4 pcs M4 x 16, 1 pcs key
•Installation manual

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
4
Provided by the installer
•Earth leakage circuit breaker (optional)
•Rail mounted terminal block (optional)
•Tools in the below section
Before installation
Make sure that the right conditions and materials are in place before installation. The
installation must be done in accordance with the instructions in this installation manual as
well as basic safety precautions.
Tools
The following tools are needed for installation:
•Knife
•A screwdriver with the below torx sizes.
•TX10 (M3 screw)
•TX20 (M4 screw)
•TX25 (M5 screw)
•TX30 (M6 screw)
Installing the Halo Pole Mount
Install and mount the Halo Pole Mount as follows

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
5
Unlock the installation lid and put aside.
Installation lid

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
6
The plastic cover has four plastic plates that can be cut off if an earth leakage circuit
breaker, ELCB, will be used. Measure the ELCB and cut away the plastic plates
corresponding to the width. Cut the plates after the plastic cover has been removed and
put aside, described in the picture below.
Plastic plates (cuttable)
Cutting point
Cutting point

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
7
Unscrew the two M3 x 6 screws, remove the plastic cover and put aside.
M3 x 6
Plastic cover
M3 x 6

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
8
Put the Halo Pole Mount in position on the pole and tighten the two locking screws.
Locking screws

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
9
Mount the handle holder on Halo Pole Mount using the 4 pcs M4 x 16 screws in the
installation kit.
M4 x 16 screws
Handle holder

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
10
There will be two Din-rails preinstalled for potential add ins, such as a terminal block,
EFCB etc.
Keep in mind to mount the earth leakage circuit breaker on the upper DIN rail for easy
access through the plastic cover.
Din-Rails

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
11
Use M5 Screw / Washer to secure the Ground wire for the Pole Mount Chassi
M5 x 8 mm
M5 Lock
Washer

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
12
Use the 3 pcs M6 x 12 screws in the installation kit to attach the Halo rear housing to the
Halo Pole Mount. Remember to put the gasket from the halo package in between the halo
rear housing and the Halo Pole Mount.
M6 x 12 screws
Halo rear
housing

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
13
Installing the Halo
Install the Halo. See separate installation manual for Halo.

© 2021 Charge Amps AB
Installation manual for
Charge Amps
Halo Pole Mount
Doc. Nr:
130095
Rev 01
Address:
Charge Amps AB
Frösundaleden 2B
SE
-169 75 Solna
Sweden
Contact:
[phone]
info@charge
-amps.com
www.chargeamps.com
Org. No. 556897-7192
Registered office: Solna
14
Reinstall the plastic cover using the two M3 x 6 screws. Use approx. 0.45 nm torque. Do
not overtighten. If use of RCB the plastic cover can be modified to fit over the RCB.
Reinstall the installation lid and lock. The lid needs a slight push close to the lock when
turning the key.
Rights
The information in this document has been checked for accuracy. Charge Amps AB
reserves the right to make technical changes and changes to the contents of the
document without prior notice. Charge Amps AB can not guarantee that all of the content
of this particular document is accurate, up-to-date, and free from printing and
proofreading errors. Moreover, Charge Amps AB cannot be held liable for any mistakes,
near-misses, injuries/damage or incidents – direct or indirect – that can be linked to the
use of the safety precautions or products in this document.
Charge Amps AB reserves all rights to this document, as well as the information and
illustrations therein. It is strictly forbidden to – in whole or in part – copy, adapt or
translate the information without prior written permission from Charge Amps AB.
© Copyright 2021, Charge Amps AB. All rights reserved.