Charge Amps Halo User manual

www.chargeamps.com
English
Charge Amps Halo
User
Manual

2
Neglecting to follow and carry out the directions, instructions and safety precautions in this User
Manual implies that any warranty provisions will be cancelled and that Charge Amps can reject any and
all claims for compensation in connection with any injuries/damage or incidents – direct or indirect –
that are a result of such negligence.
Charge Amps AB does not give any warranties as to the accuracy or completeness of this document
and shall have no liability for the consequences of using such information. Charge Amps AB reserves
the right to make changes to information published in this document without notice.
Visit www.chargeamps.com for the latest document releases.
© Copyright Charge Amps AB. All rights reserved. Copying, amending and translating are strictly
forbidden without prior written approval from Charge Amps AB.
In conformity with the relevant EU directives.
Respect the environment! Must not be discarded with household
waste! This product contains electrical or electronic components.
Leave the product for separate collection and proper treatment at
a designated location e.g. the local authority’s recycling station.

3
1 Safety
WARNING! Read all instructions before installation.
• Improper use may create a risk of personal injury.
• The product must only be installed by a qualified electrician in
accordance with the Installation Manual.
• National usage requirements and restrictions apply.
• Only use this product for charging compatible electric vehicles.
• Never use an adapter between the vehicle connector and the electric
vehicle.
• Cord extension sets are not allowed to be used.
• Inspect the product for visible damage before use.
• Never attempt to repair or use the product if it is damaged.
• Do not immerse the product in water, subject it to physical abuse or
insert foreign objects in any part of the product.
• Never attempt to disassemble the product in any way.
• Always store the vehicle connector in the holder when not in use.
• The owner is responsible for informing users of the compatibility of
any charging point.

4
2 Technical data
Charging mode Mode 3
EV power supply identifier
Metering 1 to 3 phase voltage, current and
power
Vehicle connector Type 2, 7.4/11 kW
Rated voltage (Un)230/400 V
Rated insulation voltage (Ui)250/400 V
Rated impulse withstand voltage
(Uimp)
4 kV
Rated frequency (fn)50 Hz
Rated current (In)16/32 A (depending on variant)
Rated diversity factor (RDF) 1 (can be lowered if used together with
a load balancing functionality)
Dimensions (W x D x H) Main unit: 262 x 159 x 203 mm
Vehicle connector: 81 x 125 x 88 mm
Characteristics of power supply and
output
AC EV supply equipment connected
to AC supply network, permanently
connected
Assembly type AEVCS
Cable length 7.5 m

5
RFID Type: ISO/IEC 14443 Typ A 13.56MHz
Mifare
Range: 13.553 – 13.567 MHz
Max output: 31 dBm
Wi-Fi Type: 802.11 b/g/n
Range: 2400 – 2500 MHz
Max output: 20/17/14 dBm@802.11
b/g/n

6
A Centre light and RFID reader
B Ring light
C 230 V socket-outlet (some models only)
D Vehicle connector
E Vehicle connector holder
3 Product overview
E
D
A
B
C

7
3.1 Package contents
1
RFID tag Terminal connector Cable fitting Wi-Fi antenna
Vehicle connector holder
2

8
1 Charge Amps Halo
2 Accessories
• 1x RFID tag
• 1x Five-pin terminal connector for feed current (comes in
different versions).
• 2x Cable fitting for power and data.
• 1x Wi-Fi antenna
• 1x Vehicle connector holder (comes in different versions)
• 4x Screws for Vehicle connector holder (only for certain model):
Additional contents
• Document with serial number and password
• Quick Guide
Screws are included.
Screws are not included. 2 x 3.5 mm
screws with recessed head are needed.

9
4 Use
4.1 Add RFID tag
N.B: Make sure your installer has given you the access to
Charge Amps Admin Portal to be able to manage RFID tags.
Add RFID tag using the Charge Amps cloud service:
https://my.charge.space/admin
4.2 Start and stop charging without
RFID identification
N.B: The socket-outlet is not available for use while charging
a car.
3. Initiate charging by connecting the vehicle connector to the
car.
4. Stop charging by disconnecting the vehicle connector from the
car.
5. After charging, gently wrap the charging cable around Charge
Amps Halo (NOTE: to extend the lifetime of the charging
cable, wrap the charging cable loosely) and place the vehicle
connector in the vehicle connector holder.

10
4.3 Start and stop charging with RFID
identification
N.B: The socket-outlet is not available for use while charging
a car.
1. Connect the vehicle connector to the car.
2. Initiate charging by briefly holding the RFID tag in front of the
RFID reader.
3. Stop charging by briefly holding the RFID tag in front of the
RFID reader.
4. Disconnect the vehicle connector from the car.
5. After charging, gently wrap the charging cable around Charge
Amps Halo (NOTE: to extend the lifetime of the charging
cable, wrap the charging cable loosely) and place the vehicle
connector in the vehicle connector holder.

11
4.4 Cloud connectivity
Charge Amps Cloud and Charge Amps App are available for Charge
Amps Halo connected to Charge Amps as the cloud provider.
Charge Amps App
Please download Charge Amps App for full control, adjusting
settings and enabling smart charging and scheduling.
Charge Amps Cloud
Please create an account in the Charge Amps Cloud to configure,
control and manage your charger via our web interface.
Full product information
Visit www.chargeamps.com for Charge Amps Halo Installation
Manual, Charge Amps Halo User Manual and other product
documentation.
https://my.charge.space/
My charge space
https://www.chargeamps.com/product/charge-amps-halo/
Product information

12
4.4. LED indications
4.4.1 General
Status Centre light Ring light
Ready for charging White light Steady light
Charging Steady light Circling light
Charging complete
(paused by vehicle)
White light Steady light
Charging paused*
(paused by Halo)
Flashing green light Steady light
* Power allocation can take up to 2 minutes
4.4.2 RFID tag verification
Status Centre light Ring light
Waiting for RFID tag Flashing light Steady light
RFID tag approved Green light Steady light
RFID tag not approved Red light blinking once Steady light
4.4.3 Error indications
Error Centre light Ring light
Earth fault or vehicle
error*
Red light No light
* Action: Make sure that the vehicle connector is intact. Shut off the power and
restart after a few minutes.

13
5 Maintenance
WARNING! Never spray water or any liquid directly on to the
product.
• Never spray water on the vehicle connector, immerse it in water,
or let it lie on the ground.
• Visually check that the vehicle connector is free from damage.
• Check that the vehicle connector cable is free from visible
damage.
• Check that the screw connectors securing the power cables on
the underside of the Charge Amps Halo are properly tightened.
• The outside of the product, the charging cable and the end of
the vehicle connector must be regularly wiped with a clean, dry
cloth to remove dirt and dust.
• Do not use detergent to clean any of the product’s components.
• Put the product’s vehicle connector somewhere where no one
can step on, drive on or trip over it, and where it is not damaged
or otherwise placed under stress.
• Store the vehicle connector in the holder to prevent
unnecessary exposure to contamination and moisture.
• To extend the lifetime of the charging cable, wrap the charging
cable loosely when it is not in use.

14
6 Product support and
service
If you have any questions or problems with the product, support is
always available. To find answers to your questions most quickly:
Read through this User Manual to check whether your questions
are answered here.
If your question is not answered in the User Manual, please:
1. Contact your supplier or cloud provider.
2. If you need service or repair, start by contacting the supplier
from whom you purchased the product.
3. For additional information, visit our Help Center at:
www.chargeamps.com/support.
7 Warranty
Warranty terms may differ from market to market. Contact your
supplier regarding the warranty terms.

Doc. Nr: 130624
Rev: 02
© Copyright Charge Amps AB.
All rights reserved
www.chargeamps.com Charge Amps AB (publ)
Frösundaleden 2B, 8th floor
SE–169 75 Solna, Sweden
Charge Amps UK Ltd
4th Floor, 3 More London Riverside
London SE1 2AQ, United Kingdom