Chauvet Q-WASH 560Z-LED User manual

Quick Reference Guide
All manuals and user guides at all-guides.com
all-guides.com

Q-Wash 560Z-LED QRG
Page 2 of 16
About This
Guide
The Q-Wash 560Z-LED Quick Reference Guide (QRG) contains connection
and mounting information, as well as menu options and DMX values.
Disclaimer
Refer to the User Manual for detailed information and instructions. You
can download the User Manual from the CHAUVET® website:
www.chauvetpro.com.
Read ALL the disclaimers and Safety Notes in this document, as well as
those in the product’s User Manual before installing, operating, or
maintaining this product.
Safety Notes
DO NOT open this product unless instructed. It contains no user
serviceable parts.
DO NOT look at the light source when this product is on.
DO NOT touch the product when it is operating because it may be hot.
DO NOT cover the ventilation slots when the product is operating to
avoid internal overheating.
DO NOT install or operate this product where there is less than 50 cm to
the nearest surface to allow adequate ventilation around it.
DO NOT leave any flammable material within 50 cm from this product
while operating or connected to the power outlet to minimize the risk of
fire.
DO NOT carry this product from the head. Use the handles instead.
DO NOT lift the unit by the housing. Use the handles instead.
DO NOT mount this product overhead without using a safety cable.
DO NOT operate this product outdoors or in any location where dust,
excessive heat, water, or humidity may affect it.
DO NOT operate this product if you see damage on the housing, lenses,
or cables. In any of these cases, have the damaged parts replaced by an
authorized technician immediately.
DO NOT connect this product to a dimmer or rheostat.
ONLY connect this product to a grounded and protected circuit.
All manuals and user guides at all-guides.com

Q-Wash 560Z-LED QRG
Page 3 of 16
What Is
Included
One Q-Wash 560Z-LED
One IEC Power Cord With
Edison Plug (US market)
One Safety Cable
Two Omega Brackets
Warranty Card
Quick Reference Guide
Features
12 or 15-channel RGBWA LED moving yoke wash product
Pan: 540
Tilt: 270
RGBWA color static mixing with or without DMX control
Vector speed channel for RGBWA color mixing
Variable zoom
Variable electronic strobe
Continuously variable electronic dimmer (0~100%)
Built-in automated programs
Remote product reset and vector speed channel
255-step fully customizable program
Dimming speed control via control panel or DMX
Recall auto or custom programs via control panel or DMX
Color temperature presets (3,200~10,000 K)
All manuals and user guides at all-guides.com

Q-Wash 560Z-LED QRG
Page 4 of 16
Product
Description
The Q-Wash 560Z-LED is an RGBWA LED moving yoke wash product.
This product consists of a base section and a moving yoke. The head
contains the 91 RGBWA LEDs and the zoom motors. The base section has
the 3- and 5-pin DMX input and output sockets, the IEC power input
connector, and the LCD-based control panel.
Product Overview
Power Input IEC
Socket
Power Switch
Fuse holder
3-pin DMX In
3-pin DMX Out
5-pin DMX Out
5-pin DMX In
Control panel
All manuals and user guides at all-guides.com

Q-Wash 560Z-LED QRG
Page 5 of 16
AC Power
The Q-Wash 560Z-LED has an auto-ranging power supply that works with
an input voltage range of 100~240 VAC, 50/60 Hz.
Replacing
the Fuse
1. Disconnect this product from the power outlet.
2. Using a flat head screwdriver, wedge the tip into the slot of the fuse
holder.
3. Pull out the installed fuse by prying the safety cap out of the housing.
4. Remove the blown fuse from the safety cap and replace with a fuse of
the exact same type and rating.
5. Insert the fuse holder back in place and reconnect power.
All manuals and user guides at all-guides.com

Q-Wash 560Z-LED QRG
Page 6 of 16
DMX Linking
The Q-Wash 560Z-LED will work with a DMX controller using a regular
DMX serial connection.
If you are not familiar with the DMX standard, download the DMX Primer
document from www.chauvetpro.com.
DMX Connection
The Q-Wash 560Z-LED uses a regular DMX data connection for its DMX
personalities: Advanced, Basic, and G1.
Download the Q-Wash 560Z-LED User Manual.
Refer to the Setup chapter to learn how to connect this product to DMX.
Refer to the Operation chapter to learn how to configure this product for
DMX.
Master/Slave
Connection
The Q-Wash 560Z-LED uses the DMX data connection for its Master/Slave
mode.
Download the Q-Wash 560Z-LED User Manual.
Refer to the Setup chapter to learn how to connect for master/slave
operation.
Refer to the Operation chapter to learn how to configure master/slave
operation.
All manuals and user guides at all-guides.com
all-guides.com

Q-Wash 560Z-LED QRG
Page 7 of 16
Mounting
Before mounting this product, read the Safety Notes at the beginning of this
Guide and in the User Manual.
Refer to the Setup chapter in the User Manual for detailed mounting
instructions.
Product
Mounting
Diagram
Floor Mounting
Overhead Mounting
C Clamps (not included)
Omega brackets (included)
Safety cable (included)
All manuals and user guides at all-guides.com

Q-Wash 560Z-LED QRG
Page 8 of 16
Programming
Refer to the User Manual for detailed instructions on programming this
product.
Control Panel
Description
Button
Function
<MENU>
Exit from the current menu or function
<ENTER>
Enable the currently displayed menu or accept the currently
selected value
<UP>
Navigate upward through the menu list and increase the
numeric value when in a function
<DOWN>
Navigate downward through the menu list and decrease the
numeric value when in a function
Password
After being prompted, enter the following password by pressing:
<UP>, <DOWN>, <UP>, <DOWN>, <ENTER>.
This password cannot be changed and will be the password you use each
time you are prompted.
Start Address
To ensure you can fully access all channels in each DMX mode, the highest
recommended DMX addresses are as follows:
Mode
Address
Advanced
498
Basic
501
G1
498
All manuals and user guides at all-guides.com

Q-Wash 560Z-LED QRG
Page 9 of 16
Menu Options
Main Level
Programming Levels
Description
INTRO
ADDRESS
001~512
Selects a starting DMX address
RESET
NO/YES
Resets the product’s custom settings
FAN
HIGH
Select the fan’s operation mode.
NOTE: Product’s controller will force the fan to
High if the product’s internal temperature becomes
too high, despite any manual or DMX setting
NORMAL
LOW
AUTO
RUN
DMX512
Selects DMX running mode
AUTO 1
Selects the first automatic program
AUTO 2
Selects the second automatic program
CUSTOM
Selects the user customizable program
SLAVE
Selects the Slave running mode
TEST
Starts the product’s test sequence
CHANNELS
BASIC
Selects the 11-channel DMX mode
ADVANCED
Selects the 15-channel DMX mode
G1
Selects the 15-channel DMX mode
DISPLAY
60 CLOSE
Turns off the display after 60 seconds
BRIGHT
Keeps the display on
KEYLOCK
NO/YES
Activates/deactivates the control panel password
DIMMER
DIMMER 4~1
Slow (DIM 4) to fast (DIM1) dimmer curves
DIMMER 0
Linear dimmer
INFO
EDITION
Shows the version of the installed S/W
INVERT
Pan
NORMAL/
REVERSE
Defines the pan direction
Tilt
Defines the tilt direction
Dimmer
Defines the direction of the dimmer fader
Use
NO/YES
Activates the changes
RANGE
P/Start
000~255
Sets the pan start point (restricted range)
P/Finish
Sets the pan end point (restricted range)
T/Start
Sets the tilt start point (restricted range)
T/Finish
Sets the tilt end point (restricted range)
Use
Activates the changes
SPECIAL
Black delay
NO/YES
Activates the move-in black delay (3 s)
Reset
DMX
The DMX controller can reset the product
SYSTEM
The control panel can reset the product
Power
NORMAL/
HIGH
LEDs illuminate at normal or high intensity
NOTE: Product will return to Normal if
temperature becomes too high
Color
UC
White output matches that of older products
RGBTOW
White output set by RGB-W
OFF
White output defined by RGBW faders
Fan
DMX
The DMX controller can set the fan speed
SYSTEM
The control panel can reset the fan speed
Continues on the next page
All manuals and user guides at all-guides.com

Q-Wash 560Z-LED QRG
Page 10 of 16
Main Level
Programming Levels
Description
EDIT
STEP
000~255
Selects the program step
PAN
Selects the pan position
TILT
Selects the tilt position
SPEED
Selects the pan/tilt speed
RED
Combines red, green, blue, white, and amber to
obtain a custom color
GREEN
BLUE
WHITE
AMBER
DIMMER
Selects the dimmer value
STROBE
Selects the strobe frequency and mode
ZOOM
Select the zoom position
DIMSPEED
Selects the dimmer speed
TIME
Selects the step duration
USE
No/Yes
Activates the changes
EXTRA
PASSWORD
****
Opens the Extra menu (refer to next page)
All manuals and user guides at all-guides.com