Chauvet SlimPAR QUAD 12 IRC User manual

User Manual

Page 2 of 17 SlimPAR™ QUAD 12 IRC User Manual (Rev. 1)
TABLE OF CONTENTS
1. Before You Begin ...........................................................................................................3
What Is Included .........................................................................................................................3
Unpacking Instructions ................................................................................................................3
Claims .................................................................................................................................................3
Text Conventions ........................................................................................................................3
Symbols ......................................................................................................................................3
Disclaimer ...................................................................................................................................3
Product at a Glance.....................................................................................................................4
Safety Notes ...............................................................................................................................4
2. Introduction ....................................................................................................................5
Overview.....................................................................................................................................5
Dimensions .................................................................................................................................6
3. Setup...............................................................................................................................7
AC Power....................................................................................................................................7
Fuse Replacement ...............................................................................................................................7
Power Linking ......................................................................................................................................8
Mounting .....................................................................................................................................9
Orientation...........................................................................................................................................9
Rigging................................................................................................................................................9
4. Operation ......................................................................................................................10
Control Panel Operation ............................................................................................................10
Menu Map.................................................................................................................................10
Configuration (DMX)..................................................................................................................11
Starting Address ................................................................................................................................ 11
DMX Channel Modes, Assignments, and Values .......................................................................11
8-Channel.......................................................................................................................................... 11
4-Channel.......................................................................................................................................... 11
Configuration (Standalone)........................................................................................................12
Sound-Active Mode............................................................................................................................ 12
Automatic Mode.................................................................................................................................12
Static Mode........................................................................................................................................12
Custom Static Colors.......................................................................................................................... 12
Master/Slave Mode ............................................................................................................................ 13
Infrared Remote Control ..................................................................................................................... 13
IRC (Infrared Remote Control) Operation............................................................................................ 14
5. Technical Information ..................................................................................................15
Product Maintenance ................................................................................................................15
6. Technical Specifications..............................................................................................16
Returns .....................................................................................................................................17
Contact Us ................................................................................................................................17

SlimPAR™ QUAD 12 IRC User Manual (Rev. 1) Page 3 of 17
1. BEFORE YOU BEGIN
What Is
Included
•SlimPAR™ QUAD 12 IRC
•Power Cord
•Gel Frame
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately
and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as
missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Convention
Meaning
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual
are subject to change
without notice. CHAUVET® assumes no responsibility or liabil
ity for any errors or
omissions, and reserves the right to revise or recreate this manual at any time.
Download the latest version from www.chauvetlighting.com.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date Editor Date
A. Leon 9/20/12 S. Diaz 9/21/12

Page 4 of 17 SlimPAR™ QUAD 12 IRC User Manual (Rev. 1)
Product at a
Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound-Activated

Replaceable Fuse

DMX

User-Serviceable

Master/Slave

Duty Cycle

Safety Notes
These notes include important information about the mounting, usage, and maintenance
of this product; read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•This product is not intended for permanent installation.
•Keep this User Manual for future use. If you sell the product to another user, be
sure to give this document to the next owner.

SlimPAR™ QUAD 12 IRC User Manual (Rev. 1) Page 5 of 17
2. INTRODUCTION
Overview
DMX In/Out
Back Panel View
Power In
Fuse Holder
Power Out
Microphone
Sensitivity
Adjustment Knob
Safety Loop
Microphone
Control Panel
LED Display

Page 6 of 17 SlimPAR™ QUAD 12 IRC User Manual (Rev. 1)
Dimensions

SlimPAR™ QUAD 12 IRC User Manual (Rev. 1) Page 7 of 17
3. SETUP
AC Power
The SlimPAR™ QUAD 12 IRC has an auto-
ranging power supply and it can work with
an input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker,
power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0~100% switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
A spare fuse is not included; however, the safety cap has room for a spare.
Always replace a blown fuse with the same type and rating.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 17 SlimPAR™ QUAD 12 IRC User Manual (Rev. 1)
Power Linking
The product provides power linking via the IEC outlet located in the back of the unit.
Power Linking
Diagram
You can power link up to 13 SlimPAR™ QUAD 12 IRC units on 120 VAC or up to
24 SlimPAR™ QUAD 12 IRC units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
2
nd
Product
3rd Product
1st Product
Other Products

SlimPAR™ QUAD 12 IRC User Manual (Rev. 1) Page 9 of 17
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The SlimPAR™ QUAD 12 IRC may be mounted in any position; however, make sure
adequate ventilation is provided around the product
Rigging
•Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, such as an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The brackets have a 13-mm hole, which is appropriate
for this purpose.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
•The double-bracketed yoke also serves as floor supports for
surface mounting.
When mounting the product on the floor, make sure that the product and cables are
away from people and vehicles.
Mounting Diagram
Double-Bracketed
Yoke
Safety Cable
Mounting
Clamp
Bracket Adjustment
Knob

Page 10 of 17 SlimPAR™ QUAD 12 IRC User Manual (Rev. 1)
4. OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display.
Button
Function
<MENU> Selects an operation mode or to backs out of the current menu option
<UP>
Scrolls up the list of options or selects a higher value
<DOWN> Scrolls down the list of options or selects a lower value
<ENTER> Activates a menu option or a selected value
Menu Map
Mode Programming Steps Description
P
(Auto Program)
P1
4-color program (switching)
P2
4-color program (fading)
P3 15-color program (switching)
P4
15-color program (fading)
P5 (VOL1~VOL4)
For use with IRC
4-color program (sound-active)
P6 15-color program (sound-active)
4-CH
d001~d505 4-channel DMX mode (RGBA)
8-CH
8-channel DMX mode
C
(Preset Colors)
C1 Red
Static color
C2 Green
C3
Blue
C4 Amber
C5 Cyan
C6
Purple
C7 Yellow
C8 White (RGB)
C9 Orange
C 10
Light Green
C 11
Violet
C 12
Yellow
C 13
Pink
C 14 Light Blue
C 15 White (RGBA)
S S001~S100 Program speed of P1~P4
U--
R1
~
R100
Red
Each custom static color 0~100%
Combines Red, Green, Blue, and
Amber
G1~G100 Green
b 1~b100 Blue
A1~A100 Amber
SET ON Turns infrared on or off
OFF

SlimPAR™ QUAD 12 IRC User Manual (Rev. 1) Page 11 of 17
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode
uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The SlimPAR™ QUAD 12 IRC uses up to 8 DMX channels in its 8-CH
DMX mode, which
defines the highest configurable address to 505.
If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 4-CH or 8-CH shows on the display.
2. Use <UP> or <DOWN> to select 4-CH or 8-CH.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select the starting address.
5. Press <ENTER>.
DMX Channel Modes, Assignments, and Values
8-Channel
Channel Function Value Setting
1
Red
000 255
0~100%
2
Green
000 255
0~100%
3
Blue
000

255
0~100%
4
Amber
000 255
0~100%
5
Color Macros
(Overrides Chs. 1~4)
000 015
No function
016

255
Color macros
6
Speed
(When Ch. 7 is 032~233)
000 255 Slow~fast
Strobe
000 015
No function
016 255
Slow~fast
7 Mode
000 031
RGBA mode
032 063
Pulse effect 0~100%
064 095
Pulse effect 100%~0
096 127
Pulse effect 100%~0~100%
128 159
Auto fade transition
160 191
Auto snap transition (4 colors)
192 223
Auto snap transition (15 colors)
224 255
Sound-active mode
8
Dimmer
000 255
0~100%
4-Channel
Channel Function Value Setting
1
Red
000 255
0~100%
2
Green
000 255
0~100%
3
Blue
000 255
0~100%
4
Amber
000 255
0~100%

Page 12 of 17 SlimPAR™ QUAD 12 IRC User Manual (Rev. 1)
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either Static,
Automatic, or Sound) to a DMX string connected to a DMX controller. Products in
standalone mode may transmit DMX signals that could interfere with the DMX
signals from the controller.
Sound-
Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU>repeatedly until P1~P 6 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select P5or P6.
4. Press <ENTER>.
5. Turn the music on and adjust the microphone sensitivity knob until the unit responds
to the beat of the music.
The product will only respond to low frequencies of music (bass and drums). If
there is no sound, the product will turn off.
Automatic Mode
To enable the Automatic mode, do the following:
1. Press <MENU>repeatedly until P 1~P 6 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select P1~P4.
4. Press <ENTER>.
5. Press <MENU> repeatedly until S1~S100-- shows on the display.
6. Use <UP> or <DOWN>
to adjust the duration of each step of the automatic program
from S1(slow) to S100 (fast).
7. Press <ENTER>.
Static Mode
To enable the Static mode, do the following:
1. Press <MENU> repeatedly until C 1~C 15 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the preset color (C1~C 15).
4. Press <ENTER>.
Custom Static
Colors
To enable the Custom Static Colors mode, do the following:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and one of the following colors shows on the display: RXXX (red),
GXXX (green),bXXX (blue) or AXXX (amber)
3. Press <ENTER>repeatedly to select the desired color.
4. Use <UP> or <DOWN> to select the desired color value (0~100).
NOTE: Selecting 0will turn the color off.
5. Press <ENTER> to select color value and continue to the next color.
6. Repeat steps 3 to 5 until you create your desired color.

SlimPAR™ QUAD 12 IRC User Manual (Rev. 1) Page 13 of 17
Master/Slave
Mode
The Master/Slave mode allows a single SlimPAR™ QUAD 12 IRC
unit (the “master”) to
control the actions of one or more SlimPAR™ QUAD 12 IRC
units (the “slaves”) without
the need of a DMX controller. The master unit will be set to operate in either Automatic
or Sound-Active mode, while the slave units will be set to operate in Slave m
ode. Once
set and connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU>repeatedly until 4-CH or 8-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Sound mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure all the slave units before connecting the master unit to the DMX
daisy chain.
•Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.
Infrared Remote
Control
The SlimPAR™ QUAD 12 IRC is fully compatible with the Infrared Remote Control (IRC)
from CHAUVET®. To enable usage with the IRC, do the following:
1. Press <MENU> repeatedly until SETshows on the display.
2. Press <ENTER> to accept.
3. Press <UP> or <DOWN> to select ON or OFF.
4. Press <ENTER>.

Page 14 of 17 SlimPAR™ QUAD 12 IRC User Manual (Rev. 1)
IRC (Infrared Remote
Control) Operation
Automatic Mode
Automatic mode will enable you to run the automatic programs on the
product.
To turn on Automatic mode:
1. Press <AUTO> on the IRC.
2. Press <+> or <–> to choose between the different auto programs.
To adjust the speed of the automatic program:
1. Press <SPEED> on the IRC.
2. Press <%>.
3. Press <+> or <–> to either increase or decrease the speed of the
program.
Sound-Active Mode
Sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:
1. Press <SOUND> on the IRC.
To adjust sound sensitivity in Sound-Active mode:
1. Press <SENSITIVITY> on the IRC.
2. Press <%>.
3. Press <+> or <–> to either increase or decrease sound sensitivity.
Manual Color Control
To choose a specific color with the IRC:
1. Press <MANUAL> on the IRC.
2. Press any number between 0~9to choose your color.
To manually control the RGB percentage:
1. Press <MANUAL> on the IRC.
2. Press <R> (red), <G> (green), or <B> (blue) to choose your color.
3. Press <+> or <–> to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press <STROBE> on the IRC.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
To change the switching effect of the program:
1. Press <FADE/SNAP> on the IRC.
Fade will slowly switch the effect. Snap will rapidly switch the effect.
To black out the lights:
1. Press <BLACK OUT> on the IRC.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC will not respond to any inputs when Black Out is activated. If
the remote does not respond when a button is pressed, try pressing
<BLACK OUT>. You may have inadvertently activated Black Out.

SlimPAR™ QUAD 12 IRC User Manual (Rev. 1) Page 15 of 17
5. TECHNICAL INFORMATION
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
performance and minimize wear, clean the product at least twice a month. However,
usage and environmental conditions contribute to increased cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is at room temperature.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface and vents.
•Clean the LED transparent cover with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly wipe any dirt or grime to the outside edges of the LED transparent cover.
•Gently polish the transparent LED cover until it is free of haze and lint.
Always dry the transparent LED cover carefully after cleaning.

Page 16 of 17 SlimPAR™ QUAD 12 IRC User Manual (Rev. 1)
6. TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
10.6 in (270 mm)
4.2 in (107 mm)
10.6 in (272 mm)
5.6 lbs (2.4 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
123 W
132 W
Operating current
1.0 A
0.6 A
Power linking current (units)
13.6 A (13 units)
13.6 A (24 units)
Fuse
T 2 A, 250 V
T 2 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
4 W
50,000 hours
Color
Quantity
Current
Red
12
450 mA
Green
12
450 mA
Blue
12
450 mA
Amber
12
450 mA
Photo Optic
Parameter
Illuminance @ 2 m
4,500 lx
Beam angle
20º
Field angle
34º
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
XLR
4, 8
Ordering
Product Name
Item Code
UPC Number
SlimPAR™ QUAD 12 IRC
03030601
781462209490

SlimPAR™ QUAD 12 IRC User Manual (Rev. 1) Page 17 of 17
To return a product or request support:
•In the U.S., contact CHAUVET® World Headquarters.
•In the UK or Ireland, contact CHAUVET® Europe Ltd.
•In any other country, DO NOT contact CHAUVET®. Contact your distributor. See
www.chauvetlighting.com for distributors outside the U.S., United Kingdom, or
Ireland.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® products to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET® Technical
Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product
. Be prepared to
provide the model number, serial number, and a brief description of the
cause for the
return.
You must send the merchandise prepaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write
the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are
recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk