Chauvet COLOR ADO 1-Quad TOUR User manual

Quick Reference Guide

COLORado™ 1 Quad Tour QRG
Page 2 of 12
About This
Guide
The COLORado™ 1 Quad Tour Quick Reference Guide (QRG)
contains
connection and mounting information,
as well as menu options and DMX
values.
Disclaimer
•Refer to the COLORado™ 1 Quad Tour User Manual for detailed
information and instructions. You can download the User Manual from
the CHAUVET® website: www.chauvetpro.com.
•Read ALL the disclaimers and Safety Notes in this document, as well as
those in the product’s User Manual before installing, operating, or
maintaining this product.
Safety Notes
•DO NOT open this product unless instructed to by CHAUVET®. It
contains no user-serviceable parts.
•DO NOT aim this product toward any surface closer than 16 feet (5 m).
You may damage or overheat the illuminated surface.
•DO NOT aim this product toward the Sun. The lenses could concentrate
the solar energy and cause internal overheating.
•DO NOT look at the light source when this product is on.
•DO NOT touch the product when it is operating because it may be hot.
•DO NOT install or operate this product
where there is less than 50 cm to
the nearest surface to allow adequate ventilation around it.
•DO NOT leave any flammable material within 50 cm from this product
while operating or connected to the power outlet to minimize the risk of
fire.
•DO NOT mount this product overhead without using a safety cable.
•DO NOT operate this product outdoors or in any location where dust,
excessive heat, water, or humidity may affect it.
•DO NOT operate this product if you see damage on the housing, lenses,
or cables. In any of these cases, have the damaged parts replaced by a
CHAUVET® authorized technician immediately.
•DO NOT connect this product to a dimmer or rheostat.
•ONLY connect this product to a grounded and protected circuit.
What Is
Included
•One COLORado™ 1 Quad Tour
•One NEUTRIK® PowerCON®
to Edison Plug Input Power Cord
•One Gel Frame
•One Gel Frame Holder
•One Warranty Card
•One Quick Reference Guide

COLORado™ 1 Quad Tour QRG
Page 3 of 12
Features
•3, 4, 5, 6, or 10 Quad Color LED wash light
•Operating modes
3-channel: RGB control
3-channel: HSV control
4-channel: RGB, dimmer
4-channel: RGBW
5-channel: RGBW, dimmer
6-channel: RGBW, dimmer, strobe
10-channel: RGBW, dimmer, strobe, macro, auto/custom, dimmer
curve, auto speed
•RGBW color mixing with or without DMX controller
•Built-in automated programs via Master/Slave, DMX
•Recall custom programs via Master/Slave or DMX
•Five distinct dimming curves
•RGBW Quad Color LEDs
•Electronic dimmer
•Color macros with speed adjustment included
•Electronic power supply
•Neutrik® powerCON® connectors
•Additional power output: max 11 units @ 120 V
•
3- and 5-pin DMX input and output connectors

COLORado™ 1 Quad Tour QRG
Page 4 of 12
Product
Description
The COLORado™ 1 Quad Tour is a high-
power quad color RGBW LED
wash light.
This product consists of a single module that houses the internal
power supply, the main control, the control panel, the LED drivers, the LED
boards, as well as the power and signal connectors. The COLORado™ 1
Quad Tour includes one double-bracketed yoke that can be either a
floor
mount and hanging support bracket.
Product Overview
Front View
Rear View
Side View
Quad
Color
LEDs
Power
In
Data
In
Power
Out
Data
Out
Control
Panel
Adjustment
Knob
Double-
bracketed
Yoke
Safety
Cable Loop

COLORado™ 1 Quad Tour QRG
Page 5 of 12
AC Power
The COLORado™ 1 Quad Tour has an auto-
ranging power supply that
works with an input voltage range of 100~240 VAC, 50/60 Hz.
Power Linking
You can link up to 11 COLORado™ 1 Quad Tour products at 120 VAC or
21 at 230 VAC. Make sure you never exceed the maximum number.
DMX Linking
The COLORado™ 1 Quad Tour will work with a DMX controller using a
regular DMX connection.
If you are not familiar with the DMX standard, download the DMX Primer
from www.chauvetpro.com.
DMX
Connection
The COLORado™ 1 Quad Tour uses a regular DMX data connection for
its DMX personalities: TOUR, ARC.1, AR1.D, ARC.2, AR2.D
,
AR2.S, and HSV.
Download the COLORado™ 1 Quad Tour User Manual.
Refer to Setup and Operation to learn how to connect and configure
this
product for DMX.
Master/Slave
Connection
The COLORado™ 1 Quad Tour uses the DMX data connection for its
Master/Slave mode.
Download the COLORado™ 1 Quad Tour User Manual.
Refer to Setup and Operation to learn how to connect and configure
for
Master/Slave operation.