Chauvet COLORado Panel User manual

Quick Reference Guide

Colorado™ Zoom Tour WW QRG
Page 2 of 8
About This
Guide
The Colorado™ Zoom Tour WW Quick Reference Guide (QRG) only
contains the product’s connection and mounting information,
as well as the
menu options and the DMX values.
Disclaimer
•This Quick Reference Guide does not replace the product’s User
Manual, available at www.chauvetpro.com.
•You must read ALL the disclaimers and safety notes in this document,
as well as those in the product’s User Manual before installing,
operating, or maintaining this product.
Safety
Notes
•DO NOT open this product unless instructed. It contains no
user-serviceable parts.
•DO NOT aim this product toward the Sun. The lenses could
concentrate the solar energy and cause internal overheating.
•DO NOT look at the light source when this product is on.
•DO NOT touch the product when it is operating because it may be
very hot.
•DO NOT install or operate this product where there is less than 50 cm
to the nearest surface to allow adequate ventilation around it.
•DO NOT leave any flammable material within 50 cm from this
product while operating or connected to the power outlet to minimize
the risk of fire.
•DO NOT mount this product overhead without using a safety cable.
•This product is for indoor use only! To prevent risk of fire or shock,
do not expose this product to rain or moisture.
•DO NOT operate this product if you see damage on the housing,
lenses, or cables. Have the damaged parts replaced by an authorized
technician immediately.
•DO NOT connect this product to a dimmer or rheostat.
•ONLY connect this product to a grounded and protected circuit.
What Is
Included
•One Colorado™ Zoom Tour WW
•One Neutrik® powerCON® to
Edison Plug Input Power Cord
•One Gel Frame
•One Accessory Holder
•One Warranty Card
•One Quick Reference Guide
•One Safety Cable

Colorado™ Zoom Tour WW QRG
Page 3 of 8
Features
•1, 4, or 5-channel DMX control
•Operating modes:
1-channel: Dimmer
4-channel: Dimmer, macro, zoom, zoom reset
5-channel: WW, CW, dimmer, zoom, zoom reset
•Color temperature control with or without DMX control
•8~27.5° zoom control with or without DMX control
•Five distinct dimming curves
•Cool and warm white LEDs
•Electronic dimmer
•Electronic power supply
•Neutrik® powerCON® connectors
•3- and 5-pin DMX input and output connectors
•Additional power output: max 7 units @ 120 V
•LED display with password protection
•Gel frame holder (4 mm max. thickness)
•Double-bracketed yoke doubles as floor stand
•Color calibration
•Flicker-free operation for HD Video

Colorado™ Zoom Tour WW QRG
Page 4 of 8
Product
Description
The Colorado™ Zoom Tour WW is a Warm White LED wash light. A
single module houses the internal power supply, the main control, the
control panel, the LED drivers, the LED boards, and motorized moving
lenses, as well as the power and signal connectors. The Colorado™
Zoom Tour WW features a variable zoom enabling you to change the
beam angle via DMX or control panel. One mounting bracket
doubles as
a floor mount or hanging support.
Front View
Bottom View
Power In/Out
DMX In
DMX Out
Double-
bracketed
Yoke

Colorado™ Zoom Tour WW QRG
Page 5 of 8
AC Power
This product has an auto-ranging power supply that works with an
input voltage range of 100~240 VAC, 50/60 Hz.
Power
Linking
You can link up to 7 Colorado™ Zoom Tour WW units at 120
VAC, 12 at 208 VAC, or 14 at 230 VAC.
DMX
Linking
The Colorado™ Zoom Tour WW can work with a DMX controller
when linked using a regular DMX serial connection.
If you are not familiar with the DMX standard, please download the
DMX Primer document from www.chauvetpro.com.
DMX
Connection
The Colorado™ Zoom Tour WW uses a regular DMX data
connection for its 3 DMX personalities, UNO, STD.P, and STD.W.
Download the Colorado™ Zoom Tour WW User Manual. Refer to
the Setup chapter to learn how to connect this product for DMX
operation. To learn how to configure this product for DMX
operation, refer to the Operation chapter.
Master/Slave
Connection
The Colorado™ Zoom Tour WW uses the DMX data connection for
its Master/Slave mode.
Download the Colorado™ Zoom Tour WW User Manual.Refer to
the Setup chapter to learn how to connect this product for
Master/Slave operation. To learn how to configure this product for
Master/Slave operation, refer to the Operation chapter.
Start Address
To ensure full access to all channels in each DMX mode, the highest
recommended DMX addresses are as follows:
Mode
Address
UNO 512
STD.P 509
STD.W 508

Colorado™ Zoom Tour WW QRG
Page 6 of 8
Mounting
Before mounting this product, read the Safety Notes in this guide and
in the product’s User Manual. Then, follow the mounting procedure
indicated in the Setup chapter of the User Manual.
Product
Mounting
Diagram
Floor Mounting
Overhead Mounting

Colorado™ Zoom Tour WW QRG
Page 7 of 8
Programming
For details on how to program this product, please refer to the
product’s User Manual.
Control Panel
Description
Button Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the
currently selected value into the selected function
<UP>
Navigates upwards through the menu list and increases
the numeric value when in a function
<DOWN>
Navigates downwards through the menu list and
decreases the numeric value when in a function
Password
After being prompted to enter the password, press:
<UP>, <DOWN>, <UP>, <DOWN>, <ENTER>.
Menu Options
Main Level
Programming Levels
Description
STAT
W.
000~255 Combines Warm White and Cool White to
generate a custom color (0~100%)
C.
Z.
Sets 8~27.5° zoom
DMX
001~512
Sets the DMX starting address
RUN
DMX
Receives signals from DMX controller
SLAV
Receives signals from Master unit
PERS
STD.W
5-channel: WW, CW, D, Z, ZR
STD.P
4-channel: D, Macro, Z, ZR
UNO
1 channel: D
SET
REST
Enter password
Defaults product
DIM
OFF
No dimmer
DIM1~4
Dimmer curve
DERR
BLAK
All LEDs turn off when DMX signal is lost
SAVE
All LEDs stay on the last command used
when the DMX signal is lost
CALE
YES
Allows calibration setting to be changed
NO
Locks out changes to calibration
ZOOM
BASE
Sets default zoom position (full movement)
POS.1
Sets position 1 setting for zoom limit
POS.2
Sets position 2 setting for zoom limit
CALIB1 WH 01~05
W
000~255
White calibration
C.
KEY
ON/OFF
Turns the password on or off
ZOOM
POS.1
000~255
Sets the value limit of the zoom preset
POS.2
000~255

Colorado™ Zoom Tour WW QRG
Page 8 of 8
DMX Values
UNO
Channel
Function
Value
Percent/Setting
1
Master Dimmer
000 255
0~100%
STD.P
Channel
Function
Value
Percent/Setting
1
Master Dimmer
000 255
0~100%
2 Macro
000 010
011 050
051 080
081 110
111 140
141 255
No Function
White 1
White 2
White 3
White 4
White 5
3
Zoom
000 255
0~100%
4 Zoom Reset
000

200
201 220
221 255
No Function
Zoom Reset
No Function
STD.W
Channel
Function
Value
Percent/Setting
1
Master Dimmer
000 255
0~100%
2
Warm White
000

255
0~100%
3
Cool White
000 255
0~100%
4
Zoom
000 255
0~100%
5 Zoom Reset
000 200
201 220
221 255
No Function
Zoom Reset
No Function
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom and Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [email protected]
World Wide Web
www.chauvetpro.com
World Wide Web
www.chauvetlighting.co.uk
Colorado™ Zoom Tour WW QRG – Rev. 09
© Copyright 2012 CHAUVET®
All rights reserved.
Printed in the P. R. C.