Chauvet COLORrail IRC IP User manual

User Manual

Page 2 of 16 COLORrail™ IRC IP User Manual (Rev. 3)
TABLE OF CONTENTS
1. Before You Begin...........................................................................................................3
What Is Included........................................................................................................................3
Unpacking Instructions...............................................................................................................3
Claims ..............................................................................................................................................3
Text Conventions.......................................................................................................................3
Icons..........................................................................................................................................3
Disclaimer..................................................................................................................................3
Product at a Glance...................................................................................................................4
Safety Notes..............................................................................................................................4
2. Introduction....................................................................................................................5
Product Overview.......................................................................................................................5
Product Dimensions...................................................................................................................5
3. Setup...............................................................................................................................6
AC Power ..................................................................................................................................6
Power Linking ...................................................................................................................................6
Mounting....................................................................................................................................6
Orientation........................................................................................................................................6
Rigging.............................................................................................................................................6
4. Operation........................................................................................................................7
Control Panel Operation.............................................................................................................7
Configuration (DMX) ..................................................................................................................7
DMX Personalities and Starting Address...........................................................................................7
Menu Map..................................................................................................................................8
DMX Channel Assignments and Values .....................................................................................9
2-CH.................................................................................................................................................9
3-CH.................................................................................................................................................9
4-CH.................................................................................................................................................9
7-CH.................................................................................................................................................9
14-CH.............................................................................................................................................10
26-CH.............................................................................................................................................11
Configuration (Standalone).......................................................................................................12
Auto Run Mode...............................................................................................................................12
Auto Programs................................................................................................................................12
Master/Slave Mode .........................................................................................................................12
Infrared Control...............................................................................................................................12
IRC (Infrared Remote Control) Operation.........................................................................................13
5. Technical Information..................................................................................................14
Product Maintenance...............................................................................................................14
6. Technical Specifications..............................................................................................15
Contact Procedure...................................................................................................................16
Returning Products to CHAUVET® ..........................................................................................16
CHAUVET® Contact Information..............................................................................................16

COLORrail™ IRC IP User Manual (Rev. 3) Page 3 of 16
1.BEFORE YOU BEGIN
What Is
Included
•COLORrail™ IRC IP
•DMX In Adapter
•DMX Out Adapter
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Immediately upon receipt, carefully unpack the product and check the box to make sure
you have received all the parts indicated above in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, upon receipt notify the carrier immediately, not
CHAUVET®.
Failure to do so in a timely manner may invalidate your claim with the
carrier. In addition, keep the container and all the packing material for inspection.
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of receiving the
merchandise.
Text
Conventions
Convention Meaning
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Icons
Icon Meaning
Critical installation, configuration, or operation information. Failure
to comply with this information may render the product partially or
completely inoperative, cause damage to the product, or cause
harm to the user.
Important installation or configuration information. Failure to
comply with this information may prevent the product from
functioning correctly.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual.
CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author
Date
Editor
Date
A. Diaz 6/19/12 S. Diaz 12/17/12

Page 4 of 16 COLORrail™ IRC IP User Manual (Rev. 3)
Product at a
Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a GFI (ground fault interrupter) circuit to avoid the
risk of electrocution.
•Always disconnect the product from the power source before cleaning.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor or outdoor use (IP65). Do not submerge the product.
•Always install the product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
•Never connect the product to a dimmer.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Keep this User Manual for future consultation. If you sell the product to another
user, be sure that they also receive this document.

COLORrail™ IRC IP User Manual (Rev. 3) Page 5 of 16
2.INTRODUCTION
Product Overview
Product Dimensions
Power In
DMX In
Power Out
DMX Out
LED Display

Page 6 of 16 COLORrail™ IRC IP User Manual (Rev. 3)
3.SETUP
AC Power
The COLORrail™ IRC IP has an auto-
ranging power supply and it can work with an
input voltage range of 100–240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a GFI protected circuit
(circuit breaker or fuse).
Make sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Power Linking The product provides a power linking option via the
pigtails located on the back of the
unit.
You can daisy chain up to 15 units on 120 VAC or up to 28 units on 230 VAC.
If you choose not to use the power linking feature, be sure to use the included screw on
cap to prevent any water from getting into the power cords.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The COLORrail™ IRC IP
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight. Please see the Technical Specifications section of
this manual for weight information.
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13 mm hole, which is appropriate for
this purpose.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagram
L-Brackets

COLORrail™ IRC IP User Manual (Rev. 3) Page 7 of 16
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations
on the control
panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Configuration
(DMX) Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
DMX
Personalities
and Starting
Address
The COLORrail™ IRC IP has six DMX personalities, a 2-channel mode for basic control
and a 26-channel mode with more advanced control over the lights.
The COLORrail™ IRC IP uses up to 26 DMX channels in its 26-channel DMX mode,
which defines the highest configurable address to 487.
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you
could restrict the access to some of the product’s channels.
If you are not familiar with the DMX protocol, you may refer to the DMX Primer at
www.chauvetlighting.com.
To select the DMX personality, do the following:
1. Press <MENU> repeatedly until __c shows on the display.
2. Press <ENTER>.
3. Press <MENU> repeatedly until 2-c, 3-c, 4-c, 7-c, 14c or 26c shows on the display
4. Press <ENTER> to choose your DMX personality when it appears on the display.
To then choose your starting address:
1. Press <MENU> repeatedly until 001 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
5. Press <ENTER>.

Page 8 of 16 COLORrail™ IRC IP User Manual (Rev. 3)
Menu Map
Mode
Programming Steps
Description
Auto Run AUR
n__ 01-99, FL Number of loops
S.__ 01-99, FL Run speed (slow to fast)
F.__
00-99
Strobe speed (slow to fast)
DMX Channels
and
Personalities
001 001-512 Sets DMX address
__c
2-c
Sets DMX personality
3-c
4-c
7-c
14c
26c
Slave Mode SLA Sets Slave functionality
IR Controller
ir-
IRC functionality
Auto Programs P.__
P.01
1.-r Red
2.r9 Yellow
3.-9 Green
4.9b
Cyan
5.-b Blue
6.rb Magenta
7.FL White
8.OF Off
F.01-F.99 Strobe speed (slow to fast)
P.02-
P.20
S.01-
S.99,
S.FL Run speed (slow to fast)
F.00-F.99 Strobe speed (slow to fast)
P.21-
P.22
S.01-
S.99,
S.FL Run speed (slow to fast)
F.00-F.99 Strobe speed (slow to fast)
1.-r Red
Foreground Color
1.r9 Yellow
1.-9
Green
1.9b Cyan
1.-b
Blue
1.rb Magenta
1.FL White
1.FF Off
2.-r
Red
Background Color
2.r9 Yellow
2.-9 Green
2.9b Cyan
2.-b Blue
2.rb Magenta
2.FL White
2.FF
Off

COLORrail™ IRC IP User Manual (Rev. 3) Page 9 of 16
DMX Channel Assignments and Values
2-CH
Channel Function Value Setting
1 Color Macros
000 008
No function
009 017
Red
018 026
Yellow
027 035
Green
036 044
Cyan
045 053
Blue
054 062
Magenta
063 071
White
072 242
Auto Programs
243 255
Reserved
2
Auto Program Speed
000 255
Slow to fast (when Ch. 1 is 072–255)
3-CH
Channel Function Value Setting
1
Red
000 255
0–100%
2
Green
000

255
0–100%
3
Blue
000 255
0–100%
4-CH
Channel Function Value Setting
1
Master Dimmer
000

255
0–100%
2
Red
000 255
0–100%
3
Green
000 255
0–100%
4
Blue
000 255
0–100%
7-CH
Channel Function Value Setting
1
Master Dimmer
000 255
0–100%
2
Red
000 255
0–100%
3
Green
000 255
0–100%
4
Blue
000 255
0–100%
5 Color Macros
000 008
No function
009 017
Red
018 026
Yellow
027 035
Green
036 044
Cyan
045 053
Blue
054 062
Magenta
063 071
White
072 255
Auto Programs
6 Auto Program Speed 000 255
Program speed slow to fast (when Ch. 5 is
072–255)
7
Strobe
000 255
Slow to fast

Page 10 of 16 COLORrail™ IRC IP User Manual (Rev. 3)
14-CH
Channel
Function
Value
Setting
1
Master Dimmer
000 255
0–100%
2
Red
000 255
0–100%
Section 1
3
Green
000 255
0–100%
4
Blue
000 255
0–100%
5
Red
000 255
0–100%
Section 2
6
Green
000

255
0–100%
7
Blue
000 255
0–100%
8
Red
000 255
0–100%
Section 3
9
Green
000 255
0–100%
10
Blue
000 255
0–100%
11
Red
000

255
0–100%
Section 4
12
Green
000 255
0–100%
13
Blue
000 255
0–100%
14
Strobe
000 255
Slow to fast

COLORrail™ IRC IP User Manual (Rev. 3) Page 11 of 16
26-CH
Channel
Function
Value
Setting
1
Master Dimmer
000 255
0–100%
2
Red
000 255
0–100%
Section 1
3
Green
000 255
0–100%
4
Blue
000 255
0–100%
5
Red
000 255
0–100%
Section 2
6
Green
000

255
0–100%
7
Blue
000 255
0–100%
8
Red
000 255
0–100%
Section 3
9
Green
000 255
0–100%
10
Blue
000 255
0–100%
11
Red
000

255
0–100%
Section 4
12
Green
000 255
0–100%
13
Blue
000 255
0–100%
14
Red
000 255
0–100%
Section 5
15
Green
000 255
0–100%
16
Blue
000 255
0–100%
17
Red
000 255
0–100%
Section 6
18
Green
000 255
0–100%
19
Blue
000 255
0–100%
20
Red
000 255
0–100%
Section 7
21
Green
000

255
0–100%
22
Blue
000 255
0–100%
23
Red
000 255
0–100%
Section 8
24
Green
000 255
0–100%
25
Blue
000 255
0–100%
26
Strobe
000 255
Slow to fast

Page 12 of 16 COLORrail™ IRC IP User Manual (Rev. 3)
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product
that is operating in any standalone mode to a DMX string
connected to a DMX controller. Product
s in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Auto Run Mode
To enable the Automatic Mode, follow the instructions below:
1. Press <MENU> repeatedly until AUR shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose between programming levels.
a. To adjust the number of loops in the program, press <MENU> until n__ shows,
press <ENTER>, then <UP> or <DOWN> to adjust the loop numbers (01-99, FL).
b. To adjust the run speed in the program, press <MENU> until S.__ shows, press
<ENTER>, then <UP> or <DOWN> to adjust the run speed from slow to fast (01-
99, FL).
c. To adjust the strobe speed in the program, press <MENU> until F.__ shows, press
<ENTER>, then <UP> or <DOWN> to adjust the strobe speed from slow to fast
(01-99, FL).
Auto Programs
To enable the Automatic Mode, follow the instructions below:
1. Press <MENU>repeatedly until P.__ shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose between auto programs (P.01-P.22).
4. Press <ENTER>.
Master/Slave
Mode The Master/Slave mode allows a single COLORrail™ IRC IP unit (the “master”) to control
the actions of one or more COLORrail™ IRC IP
units (the “slaves”) without the need of a
DMX controller. The master unit will be set to operate in any standalone
mode, while the
slave units will be set to operate in Slave Mode. Once set and connected, the slave units will
operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU>repeatedly until SLA shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5.
Connect the DMX input of the subsequent slave units to the DMX output of the previous
slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in any standalone mode.
2. Make the master unit the first unit in the daisy chain.
•Configure all the slave units before connecting the master unit to the daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the master
unit.
•
Do not connect more than 31 slave units to the master unit.
Infrared Control The COLORrail™ IRC IP is fully compatible with the Infrared Remote Control from
CHAUVET® (sold separately). To enable the IRC, follow the instructions below:
1. Press <MENU> repeatedly until ir- shows on the display.
2. Press <ENTER>.

COLORrail™ IRC IP User Manual (Rev. 3) Page 13 of 16
IRC (Infrared Remote Control) Operation
Note: Make sure to point the IRC directly at the receiver on the product.
Automatic Mode
Automatic Mode will enable you to run the automatic programs on the
product.
To turn on Automatic Mode:
1. Press AUTO on the IRC.
2. Press + or – to choose between the different auto programs.
To adjust the speed of the automatic program:
1. Press SPEED on the IRC.
2. Press %.
3. Press + or – to either increase or decrease the speed of the program.
Sound Active Mode (if available)
Sound Active Mode will enable the product to respond to the music.
To turn on Sound Active mode:
1. Press SOUND on the IRC.
To adjust sound sensitivity in Sound Active mode:
1. Press SENSITIVITY on the IRC.
2. Press %.
3. Press + or – to either increase or decrease sound sensitivity.
Manual Color Control
To choose a specific color with the IRC:
1. Press MANUAL on the IRC.
2. Press any number between 0-9 to choose your color.
To manually control the RGB percentage:
1. Press MANUAL on the IRC.
2. Press R, G, or B to choose your color.
3. Press + or – to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press STROBE on the IRC.
2. Press + or – to increase or decrease the strobe rate.
3. Press STROBE again to turn off the strobe.
To change the switching effect of the program:
Press FADE/SNAP on the IRC.
Fade will slowly switch the effect. Snap will rapidly switch the effect.
To black out the lights:
Press BLACK OUT on the IRC.
This will turn off all the lights until the button is pressed again.
Note: The IRC will not respond to any inputs when Black Out is activated. If
the remote does not respond when a button is pressed, try pressing
BLACK OUT. You may have inadvertently activated BLACK OUT.

Page 14 of 16 COLORrail™ IRC IP User Manual (Rev. 3)
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life.
To maintain optimum performance and
minimize wear, you should clean your lighting products at least twice a month. However,
be aware that usage and environmental conditions could be contributing factors to
increase the cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is cold.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all external optics and glass/transparent surfaces with a mild soap solution,
ammonia-free glass cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
•Softly drag any dirt or grime to the outside of the external optics or glass/transparent
surface.
•Gently polish the external optics and glass/transparent surfaces until they are free of
haze and lint
Always dry the external optics and glass/transparent
surfaces carefully after
cleaning them.

COLORrail™ IRC IP User Manual (Rev. 3) Page 15 of 16
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
4.7 in (120 mm)
43.6 in (1109 mm)
5.1 in (130 mm)
12.4 lbs (5.6 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100–240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
60 W
65 W
Operating
0.5 A
0.3 A
Power linking current (units)
8 A (15 units)
8 A (28 units)
Fuse
Internal
Internal
Power I/O
US/Worldwide
UK/Europe
Power input connector
Proprietary
Proprietary
Power output connector
Proprietary
Proprietary
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Lifespan
LED
50,000 hours
Color
Quantity
Red
128
Green
96
Blue
96
Photo Optic
Parameter
Illuminance @ 2 m
418 lux
Beam angle
14º
Field angle
22°
Thermal
Maximum External Temp.
Minimum Startup Temp.
Cooling System
113° F (45° C)
-4° F (-20° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Proprietary
2, 3, 4, 7, 14, 26
Ordering
Product Name
Item Code
Item Number
COLORrail™ IRC IP
03030121
COLORRAILIRCIP

Page 16 of 16 COLORrail™ IRC IP User Manual (Rev. 3)
Contact
Procedure
In case you need to return a product or request support, follow the procedure below:
•If you live in the U.S., contact CHAUVET® World Headquarters (see below).
•If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. See www.chauvetlighting.com for distributors outside the U.S.,
United Kingdom, or Ireland.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® product
s to
them. Visit our website for contact details.
Returning
Products
to
CHAUVET®
Call the corresponding CHAUVET®
Tech Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product
. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid
, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write
the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. As a suggestion, proper UPS packing or double-
boxing is always a safe method to use.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).
CHAUVET®
Contact
Information
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk