Chauvet SHOKER PANEL 180 USB User manual

User Manual

Page 2 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 3
What Is Included .............................................................................................................................3
Unpacking Instructions....................................................................................................................3
Claims..................................................................................................................................................... 3
Text Conventions ............................................................................................................................3
Symbols ..........................................................................................................................................3
Disclaimer .......................................................................................................................................3
Product at a Glance ........................................................................................................................4
Safety Notes....................................................................................................................................4
2. Introduction................................................................................................................... 5
Product Overview............................................................................................................................5
Product Dimensions........................................................................................................................6
3. Setup.............................................................................................................................. 7
AC Power........................................................................................................................................7
Fuse Replacement..........................................................................................................................7
Power Linking......................................................................................................................................... 7
Mounting .........................................................................................................................................8
Orientation.............................................................................................................................................. 8
Rigging ................................................................................................................................................... 8
4. Operation....................................................................................................................... 9
Control Panel Operation..................................................................................................................9
Menu Map .......................................................................................................................................9
DMX Linking..................................................................................................................................10
Configuration (DMX)............................................................................................................................. 10
D-Fi™ USB Connectivity...............................................................................................................10
Configuration (D-Fi™ USB).................................................................................................................. 10
DMX Personality and Starting Address................................................................................................. 11
DMX Channel Assignments and Values.......................................................................................11
8-CH..................................................................................................................................................... 11
5-CH..................................................................................................................................................... 12
2-CH..................................................................................................................................................... 12
Shocker™ Panel 180 Zones for DMX Control...................................................................................... 12
Configuration (Standalone)...........................................................................................................13
Automatic Programs............................................................................................................................. 13
Sound-Active Mode .............................................................................................................................. 13
Custom Mode ....................................................................................................................................... 13
Auto-Program Speed............................................................................................................................ 13
Sound Sensitivity.................................................................................................................................. 13
Temperature......................................................................................................................................... 13
IRC-6 Infrared Remote Control.....................................................................................................14
IRC-6 Operation.................................................................................................................................... 14
Master/Slave Mode (wired)...........................................................................................................15
Master/Slave Mode (D-Fi™ USB).................................................................................................15
5. Maintenance .................................................................................................................16
Product Maintenance....................................................................................................................16
6. Technical Specifications..............................................................................................17
Returns .............................................................................................................................18
Contact Us........................................................................................................................19

Shocker™ Panel 180 USB User Manual Rev. 1 Page 3 of 19
1.BEFORE YOU BEGIN
What Is
Included
•Shocker™ Panel 180 USB
•Power Cord •Warranty Card •Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure al
l the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure
to report damage to the carrier immediately may invalidate your claim. In addition, keep the
box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Electrical warning. Not following these instructions may cause
electrical damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. Chauvet assumes no responsibility or liability for any errors o
r omissions
that may appear in this manual. Chauvet
reserves the right to update the existing
document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2015 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Updated
R. Isenstadt 05/08/15 M. Trouard 07/09/15

Page 4 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•The product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to someone else, be
sure that they also receive this document.

Shocker™ Panel 180 USB User Manual Rev. 1 Page 5 of 19
2.INTRODUCTION
Product Overview
WARNING! DO NOT plug anything other than a D-Fi™ USB into the USB port. Doing
so may cause damage to the product.
Bracket Adjustment Knob
Mounting Brackets
LCD Display
Power In
Microphone
Power Out
Fuse holder
D-Fi™ USB
Port
DMX In
DMX Out
Menu Buttons
Safety Loop
IR Sensor
Front View
Back Panel View

Page 6 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
Product Dimensions
7.8 in
198 mm
2.25 in
57 mm
8.8 in
223 mm

Shocker™ Panel 180 USB User Manual Rev. 1 Page 7 of 19
3.SETUP
AC Power
The Shocker™ Panel 180 USB has an auto-ranging power supply and it can work with an
input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power
requirements (
circuit breaker, power outlet, and wiring), use the current value listed on the
label affixed to the product’s back panel, or refer to the product
’s specifications chart. The
listed current rating indicates the product’s average current draw under normal conditions.
•Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has an appropriate electrical
ground to avoid the risk of
electrocution or fire.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (
variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
2. Pry the fuse holder out of the housing.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
4. Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking The product provides power linking via the Edison outlet located in the back of the product.
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 13 Shocker™ Panel 180 USB product
s on 120 VAC or up
to 24 Shocker™ Panel 180 USB products on 230 VAC.
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product
in other markets, you must consult with the
local Chauvet distributor as power linking connectors and requirements may differ
in your country or region.
1st Product
2nd Product
3rd Product
Additional
Products
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in the
Safety Notes.
Orientation
The Shocker™ Panel 180 USB
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy access
to the product for maintenance and programming purposes.
•Make sure that the structure onto which you are mounting the product can support the
product’s weight. See the Technical Specifications for weight information.
•When mounting the product overhead, always use a safety cable. Mount the product
securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, use a mounting clamp
of appropriate weight
capacity.
•When power linking multiple products, mount the products close enough for power
linking cables to reach.
•The bracket adjustment
knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
Mounting Diagram
Mounting Clamp
(such as the CLP-15N
from Chauvet)
Hanging/Mounting
Bracket
(also used as floor
supports)
Safety Cable
(such as CH-05 from
Chauvet)
Bracket Adjustment
Knob x 2

Shocker™ Panel 180 USB User Manual Rev. 1 Page 9 of 19
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the display.
Please refer to the Product Overview to see the button locations on the control panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER>
Press to activate a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
2-CH
d 1–d512
2-channel DMX mode
5-CH
5-channel DMX mode
8-CH
8-channel DMX mode
P--
P 1–P 8
Auto program
S--
S 1–S100
Program speed
U--
d 0–d255
Custom mode, sets dimmer
S 0–S255
Custom mode, sets strobe, slow to fast
Snd
Snd1
Sound-Active mode
Snd2
SenS
u 0–u100
Sound Sensitivity Setting
SEr
ON
IR function on or off
OFF
teMP
XX
Displays the product temperature

Page 10 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
DMX Linking
The Shocker™ Panel 180 USB works with a DMX controller. Information about DMX is in
the CHAUVET® DMX Primer, which is available from the Chauvet website
http://www.chauvetlighting.com/.
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
D-Fi™ USB
Connectivity
The Shocker™ Panel 180 USB is able to become a D-Fi™ wireless receiver/transmitter with
the use of the D-Fi™ USB from Chauvet DJ. Simply set the product's DMX Personality and
DMX Address, set the DIP switch D-Fi™ receiving/transmitting channel, then plug it into the
D-Fi™ USB port.
WARNING! DO NOT plug anything other than a D-Fi™ USB into the USB port. Doing
so may cause damage to the product.
Once plugged in, the D-Fi™ USB will take over the product. Wired DMX, manual
display control / menu buttons and IRC will be unavailable until you unplug the D-
Fi™ USB. The priority levels are:
1. D-Fi™ USB
2. Wired DMX
3. IRC-6 Remote Control
4. Manual Digital Display/Menu Buttons
Configuration
(D-Fi™ USB)
1. Set the DMX Personality and DMX address on your product.
2. Use the Chart provided to set BOTH:
•the Channel, and then
•the Receiving or Transmitting option.
NOTE: DIP Switch 5 is for Transmitting OR Receiving, please choose carefully.
D-Fi™ USB DIP Switch
Channels
RECEIVING
TRANSMITTING

Shocker™ Panel 180 USB User Manual Rev. 1 Page 11 of 19
DMX Personality
and
Starting
Address
When selecting a starting DMX address, always consider the number of DMX channels the
selected DMX mode uses. If you choose a starting address
that is too high, you could
restrict the access to some of the product’s channels.
The Shocker™ Panel 180 USB uses up to 8 DMX channels in a 8-CH DMX mode
, which
defines the highest configurable address to 505.
If you are not familiar with the DMX protocol
, download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 2-CH, 5-CH, or 8-CH shows on the display.
2. Press <ENTER> and d1–d512 will show on the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
DMX Channel Assignments and Values
8-CH
Channel
Function
Value
Percent/Setting
1 Zone 1
000
ó
005
No function
006
ó
249
Strobe rate (slow to fast)
250
ó
255
Continuous on (blinder effect)
2 Zone 2
000
ó
005
No function
006ó249 Strobe rate (slow to fast)
250
ó
255
Continuous on (blinder effect)
3 Zone 3
000
ó
005
No function
006
ó
249
Strobe rate (slow to fast)
250
ó
255
Continuous on (blinder effect)
4 Zone 4
000ó005 No function
006
ó
249
Strobe rate (slow to fast)
250
ó
255
Continuous on (blinder effect)
5 Auto/Sound-Active
Programs
000
ó
020
No function
021
ó
040
Auto program 1
041ó060 Auto program 2
061
ó
080
Auto program 3
081
ó
100
Auto program 4
101
ó
120
Auto program 5
121
ó
140
Auto program 6
141ó160 Auto program 7
161
ó
180
Auto program 8 (Auto programs 1–7)
181
ó
225
Sound-active mode 1
226
ó
255
Sound-active mode 2
6
Auto Speed
(when Channel 5 is set
at 021–180)
000ó255 Auto program speed (slow to fast)
Sound Sensitivity
(when Channel 5 is set
at 181–255)
000
ó
010
No function
011ó255 Sound sensitivity
7
Dimmer
000ó255 0–100%
8
Strobe All Zones
(when Channel 1-4 set
at 006–255)
000ó005 No function
006ó255 Strobe rate (slow to fast)

Page 12 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
5-CH
Channel
Function
Value
Percent/Setting
1 Dimmer
000
ó
005
No function
006
ó
255
0–100%
2 Strobe Speed
000
ó
005
No function
006
ó
255
Strobe speed (slow to fast)
3
Shutter
(When Channel 2 is set
at
006
–
255
)
000
ó
005
Open
006ó255 Pulse speed (slow to fast)
4 Strobe Effects
(When Channel 2 is set
at 006–255)
000
ó
005
No function
006
ó
042
Ramp up
043ó085 Ramp down
086
ó
128
Ramp up – ramp down
129
ó
171
Random
172
ó
214
Lightning
215
ó
255
Spikes
5 Zone Strobe Macros
000
ó
005
No function
006
ó
042
Macro 1(slow to fast)
043
ó
085
Macro 2 (slow to fast)
086
ó
128
Macro 3(slow to fast)
129
ó
171
Macro 4 (slow to fast)
172
ó
214
Macro 5 (slow to fast)
215
ó
255
Macro 6 (slow to fast)
2-CH
Channel
Function
Value
Percent/Setting
1 Strobe Speed
000ó001 No function
002
ó
249
Strobe speed (slow to fast)
250
ó
255
Continuous on (blinder effect)
2
Dimmer
000ó255 0–100%
Shocker™ Panel 180 Zones for DMX Control
0
0 0 0
1 2 3
4

Shocker™ Panel 180 USB User Manual Rev. 1 Page 13 of 19
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode
to a DMX string
connected to a DMX controller. Product
s in standalone mode may transmit DMX
signals that could interfere with the DMX signals from the controller.
Automatic
Programs
To run the Shocker™ Panel 180 USB in automatic mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> and <DOWN> to select an auto program P1–P 8.
4. Press
<ENTER>
.
Sound-Active
Mode To run the Shocker™ Panel 180 USB in sound-active mode, do the following:
1. Press <MENU> repeatedly until SNd shows on the display.
2. Press <ENTER>.
3. Use <UP> and <DOWN> to select a sound-active program Snd1 or Snd2.
4. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Custom Mode
To custom mix a static color, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and dxxx will show on the display:
3. Use <UP> and <DOWN> to increase or decrease the dimmer value.
4. Press <ENTER> and Sxxx will show on the display.
5. Use <UP> and <DOWN> to increase or decrease the strobe speed.
Auto-Program
Speed
To change the auto-program speed on the Shocker™ Panel 180 USB, do the following:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> and <DOWN> to increase or decrease the program speed (S1–S100).
3. Press <ENTER>. The product will return to the last selected mode.
Sound Sensitivity
To change the sound sensitivity on the Shocker™ Panel 180 USB, follow the instructions
below:
1. Press <MENU> repeatedly until SenS shows on the display.
2. Use <UP> and <DOWN> to increase or decrease the sound sensitivity (u 0–u100).
3. Press <ENTER>. The product will return to the last selected mode.
Temperature
To view the current temperature of the Shocker™ Panel 180, follow the instructions below:
1. Press <MENU> repeatedly until teMP shows on the display.
2. Press <ENTER>.

Page 14 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
IRC-6 Infrared
Remote
Control
The Shocker™ Panel 180 USB is compatible with the IRC-6 infrared remote control from
Chauvet. To activate IR mode, follow the instructions below:
1. Press <MENU> repeatedly until SErshows on the display.
2. Press <ENTER> to accept.
3. Press <UP> or <DOWN> to select ON or OFF.
4. Press <ENTER>.
IRC-6 Operation
Automatic Mode
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:
1. Press <AUTO> on the IRC.
2. Press <+> or <–> to choose between the different auto programs.
To adjust the speed of the automatic program:
1. Press <SPEED> on the IRC.
2. Press <+> or <–> to either increase or decrease the speed of the program.
Sound-Active Mode
Sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:
1. Press <SOUND> on the IRC.
2. Press <+> or <–> toselect Snd1 or Snd2.
To adjust sound sensitivity in Sound-Active mode:
1. Press <SENSITIVITY> on the IRC.
2. Press <+> or <–> to either increase or decrease sound sensitivity.
Manual Strobe Control
To adjust the dimmer level:
1. Press <MANUAL> on the IRC.
2. Press <+> or <–> to increase or decrease the dimmer level.
To adjust the strobe rate:
1. Press <STROBE> on the IRC.
2. Press <+> or <–> to increase or decrease the strobe rate.
Black Out
To black out the lights:
Press <BLACK OUT> on the IRC.
This will turn off all the lights until the button is pressed again.
NOTE: The IRC will not respond to any inputs when Black Out is activated. If the remote
does not respond when a button is pressed, try pressing <BLACK OUT>. You may
have inadvertently activated Black Out.

Shocker™ Panel 180 USB User Manual Rev. 1 Page 15 of 19
Master/Slave
Mode
(wired)
The Master/Slave mode allows a single Shocker™ Panel 180 USB product (the “master”)
to control the actions of one or more Shocker™ Panel 180 USB product
s (the “slaves”)
without the need of a DMX controller. The master product
will be set to operate in either
Automatic or Sound-Active mode, while the slave products will be set to operat
e in Slave
mode. Once set and connected, the slave product
s will operate in unison with the master
product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 2-CH, 5-CH, or 8-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Connect the DMX input of the first slave product to the DMX output of the master
product.
5. Connect the DMX input of the subsequent slave products to the DMX output of the
previous slave product.
6. Finish setting and connecting all the slave products.
Master product:
1. Set the master product to operate in either Automatic or Sound mode.
2. Make the master product the first product in the DMX daisy chain.
•Configure all the slave products before connecting the master to the daisy
chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the master.
•Do not connect more than 31 slaves to the master.
Master/Slave
Mode
(D-Fi™ USB)
The D-Fi™ USB allows a single Shocker™ Panel 180 USB product
(the “master”) to
control the actions of one or more Shocker™ Panel 180 USB product
s (the “slaves”)
without the need of a DMX controller or DMX cables. The master (transmitter) product will
be set to operate in either Automatic or Sound-Active mode, while the slave (receiver)
products will be set to operate in Slave mode. Once set and connected, the slave products
will operate in unison with the master product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until 2-CH, 5-CH, or 8-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Set the D-Fi™ USB to receive on a specific channel, 1–16.
5. Plug in the D-Fi™ USB.
6. Finish setting and connecting all the slave products.
Master product:
1. Press <MENU> repeatedly until the DMX personality the slaves are set to shows on
the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d 1.
4. Set the master product to operate in either Automatic or Sound mode.
5. Set the D-Fi™ USB to transmit on the D-Fi™ channel the slaves are receiving on.
6. Plug in the D-Fi™ USB.
•All products must be set to the same DMX personality, DMX address, and D-Fi™
channel.
•Configure all the slave products before configuring the master to transmit.
•Never connect a DMX controller to a D-Fi™ channel
configured for Master/Slave
operation because the controller may interfere with the signals from the master.

Page 16 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
5.MAINTENANCE
Product
Maintenance
Dust build-up reduces light output perform
ance and can cause overheating. This can lead
to reduction of the light source’s life and/or
mechanical wear. To maintain optimum
performance and minimize wear, clean your lighting product
s at least twice a month.
However, be aware that usage and environme
ntal conditions could be contributing factors
to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust
collected on the external surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning
tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.

Shocker™ Panel 180 USB User Manual Rev. 1 Page 17 of 19
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
2.25 in (57 mm)
8.8 in (223 mm)
7.8 in (798 mm)
3.4 lb (1.6 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
41 W
40 W
Operating Current
0.6 A
0.3 A
Power linking current
(products)
8 A (13 products) 8 A (24 products)
Fuse
T 3.15 A, 250 V
T 3.15 A, 250 V
Power I/O
U.S./Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
SMD LED
0.5 W
50,000 hours
Color
Quantity
Current
Cool white
180
644 mA
Photometrics
Parameter
Strobe Rate
0 to 29 Hz
Beam Angle
65°
Field Angle
107°
Illuminance @ 2 m
257 lux
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
DMX
I/O Connectors
Channel Range
3-pin XLR
2, 5 or 8
Ordering
Product Name
Item Code
UPC Number
Shocker™ Panel 180 USB
03031062
781462214104

Page 18 of 19 Shocker™ Panel 180 USB User Manual Rev. 1
R
ETURNS
In case you need to get support or return a product:
•If you are located in the U.S., contact Chauvet World Headquarters.
•If you are located in the UK or Ireland, contact Chauvet Europe Ltd.
•If you are located in Mexico, contact Chauvet Mexico.
•If you are located in Benelux, contact Chauvet Europe BVBA.
•If you are located in any other country, DO NOT contact Chauvet. Instead, contact
your local distributor. See www.chauvetlighting.com for distributors outside the U.S.,
UK, Ireland, Mexico, or Benelux.
If you are located outside the U.S., UK, Ireland, Mexico, or Benelux, contact your
distributor of record and follow their instructions on how to return Chauvet
products to them. Visit our website www.chauvetlighting.com for contact details.
Call the corresponding Chauvet Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
Send the merchandise prepaid, in its original box, and with its original packing and
accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are
recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).

Shocker™ Panel 180 USB User Manual Rev. 1 Page 19 of 19
C
ONTACT
U
S
WORLD HEADQUARTERS - Chauvet
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: tec[email protected]
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - Chauvet Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: ukt[email protected]om
World Wide Web www.chauvetlighting.co.uk
MEXICO - Chauvet Mexico
General Information
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Technical Support
Email: servic[email protected]
World Wide Web www.chauvet.com.mx
CHAUVET EUROPE - Chauvet Europe BVBA
General Information
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.eu
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux
contact your dealer. Follow their
instructions to request support or to return a product. Visit our website for contact details.