Chauvet SlimPAR PRO VW User manual

User Manual

Page 2 of 18 SlimPAR™ Pro VW User Manual Rev. 6
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 3
What is Included...............................................................................................................................3
Unpacking Instructions.....................................................................................................................3
Claims ....................................................................................................................................................... 3
Text Conventions .............................................................................................................................3
Symbols............................................................................................................................................3
Disclaimer.........................................................................................................................................3
Product at a Glance..........................................................................................................................4
Safety Notes.....................................................................................................................................4
2. Introduction................................................................................................................... 5
Overview...........................................................................................................................................5
Dimensions.......................................................................................................................................6
3. Setup.............................................................................................................................. 7
AC Power .........................................................................................................................................7
Fuse Replacement .................................................................................................................................... 7
Power Linking............................................................................................................................................ 8
Mounting...........................................................................................................................................9
Orientation................................................................................................................................................. 9
Rigging...................................................................................................................................................... 9
Lens Assembly Replacement.........................................................................................................10
4. Operation......................................................................................................................11
Control Panel Operation.................................................................................................................11
Menu Map.......................................................................................................................................11
Configuration (DMX).......................................................................................................................12
Starting Address...................................................................................................................................... 12
DMX Channel Modes, Assignments, and Values ..........................................................................13
7-Channel................................................................................................................................................ 13
3-Channel................................................................................................................................................ 13
2-Channel................................................................................................................................................ 13
Configuration (Standalone) ............................................................................................................14
Automatic Mode....................................................................................................................................... 14
Color Temperature Preset....................................................................................................................... 14
Custom Static Color................................................................................................................................. 14
Dimming Curve........................................................................................................................................ 14
Master/Slave Mode.................................................................................................................................. 15
5. Technical Information..................................................................................................16
Product Maintenance .....................................................................................................................16
6. Technical Specifications..............................................................................................17
Returns...........................................................................................................................................18
Contact Us......................................................................................................................................18

SlimPAR™ Pro VW User Manual Rev. 6 Page 3 of 18
1.BEFORE YOU BEGIN
What is
Included
•SlimPAR™ Pro VW
•Power Cord
•Hanging Bracket with Mounting
Hardware
•Gel Frame Holder
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately
and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as
missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Convention Meaning
1 to 512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual
are subject to change
without notice. CHAUVET® assumes no responsibility or liabil
ity for any errors or
omissions,
and reserves the right to revise or recreate this manual at any time.
Download the latest version from www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Printed in P.R.C.
Electronically published by CHAUVET® in the United States of America.
Author
Date
Editor
Date
A. Leon 11/08/13 D. Couppe 11/08/13

Page 4 of 18 SlimPAR™ Pro VW User Manual Rev. 6
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
x
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
These notes include important information about the mounting, usage, and maintenance
of this product; read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer or rheostat.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•
This product is not intended for permanent installation.
•Keep this User Manual for future use. If you sell the product to another user, be
sure to give this document to the next owner.

SlimPAR™ Pro VW User Manual Rev. 6 Page 5 of 18
2.INTRODUCTION
Overview
Back Panel View
Menu Buttons
Power In
Fuse Holder
DMX Out
DMX In
Power Out
Display
Passageway for
Safety Cable

Page 6 of 18 SlimPAR™ Pro VW User Manual Rev. 6
Dimensions
285 mm
11.2 in

SlimPAR™ Pro VW User Manual Rev. 6 Page 7 of 18
3.SETUP
AC Power
The SlimPAR™ Pro VW has an auto-
ranging power supply and it can work with an input
voltage range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (
circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product
’s back panel, or
refer to the product
’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
A spare fuse is not included; however, the safety cap has room for a spare.
Always replace a blown fuse with another of the same type and rating.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 18 SlimPAR™ Pro VW User Manual Rev. 6
Power Linking
The product provides power linking via the Edison/IEC outlet located in the back of the
unit.
Power Linking
Diagram
You can power link up to 11 SlimPAR™ Pro VW unit
s on 120 V or up to
18 SlimPAR™ Pro VW units on 230 V.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1st Product
2
nd
Product
3rd Product
Additional Products

SlimPAR™ Pro VW User Manual Rev. 6 Page 9 of 18
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The SlimPAR™ Pro VW
may be mounted in any position; however, make sure adequate
ventilation is provided around the product
Rigging
•Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, such as an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has 13-mm holes, which are
appropriate
for this purpose.
•When power linking multiple products, you must
always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The bracket adjustment
knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
•The double-bracketed yoke also allows for surface mounting. When mounting the
product on the floor, make sure that the product and cables are a
way from people
and vehicles.
Mounting Diagram
Bracket
Adjustment
Knob (x2)
Hanging/Mounting
Bracket
Mounting Clamp
Safety Cable

Page 10 of 18 SlimPAR™ Pro VW User Manual Rev. 6
Lens Assembly
Replacement
The SlimPAR™ Pro VW comes with a factory-installed wide-
angle lens assembly. A
narrow lens (17°) assembly is available as an optional accessory (SPPVWLENS17).
This narrow lens assembly will alter the beam and field angles of the fixture.
To replace the lens assembly, follow the instructions below.
1. Remove the four Allen screws from the front trim ring with a #3 metric Allen wrench.
2. Remove the front cover (with glass still attached to the ring).
3. You now have access to the lens assembly. Use a Philips-head screwdriver to
remove the five screws that hold it in place.
4. Carefully remove the lens assembly. The LEDs and circuit board will now be
exposed. Use caution to prevent damaging them.
5. Place the new lens assembly in the fixture and reinstall the five Philips screws.
Tighten screws as simultaneously as possible to the same tension. Do not over-
tighten the screws as this could cause damage.
6. Put the front cover in place and reinstall the five Allen screws.
Allen Screw
Allen Screw
Allen Screw
Allen Screw
Lens
Assembly
Front Cover

SlimPAR™ Pro VW User Manual Rev. 6 Page 11 of 18
4.OPERATION
Control Panel
Operation
To
access the control panel functions, use the four buttons located underneath the
display.
Button Function
<MENU> Selects an operation mode or backs out of the current menu option
<UP>
Scrolls up the list of options or selects a higher value
<DOWN> Scrolls down the list of options or selects a lower value
<ENTER> Activates a menu option or a selected value
Menu Map
Mode
Programming Steps
Description
DMX Address Addr d001–d512 Selects the DMX starting address
Personality PERS
7CH 7-channel operating mode
3CH 3-channel operating mode: warm/cool white
color temperature mixing with dimmer
2CH 2-channel operating mode: warm/cool white
color temperature mixing
Dimming Curve dIM
OFF Dimming curve: off
dIM1 Dimming curve: dim 1
dIM2 Dimming curve: dim 2
dIM3
Dimming curve: dim 3
Color
Temperature
Preset C--
C-01 White 1, 2800 K
C-02 White 2, 3000 K
C-03 White 3, 3300 K
C-04 White 4, 3600 K
C-05 White 5, 4000 K
C-06 White 6, 4500 K
C-07
White 7, 5600 K
C-08 White 8, 6000 K
C-09 White 9, 6300 K
Custom Static
Color U--
A000–A255
Combine warm and cool white to create a
custom, static color temperature mix
W000–W255
S000–S020 Strobe speed (0–20 Hz)
Auto Program P--
P--1–P--5
Program selection
S000–S100 Run speed
There is no strobing in the following modes: C--and P--. For full function control,
use 7-Channel DMX mode.

Page 12 of 18 SlimPAR™ Pro VW User Manual Rev. 6
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to power.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The SlimPAR™ Pro VW uses up to 7 DMX channels in 7-channel
DMX mode, which
defines the highest configurable address to 506.
If unfamiliar with DMX or DIP switches,
download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>repeatedly until PERS shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the desired personality: 7-CH (7-channel),
3CH (3-channel), or 2CH (2-channel).
4. Press <ENTER>.
5. Press <MENU> repeatedly until Addr shows on the dispay.
6. Press <ENTER>.
7. Use <UP> or <DOWN> to select the desired DMX starting address, d001–d512.
8. Press <ENTER>.

SlimPAR™ Pro VW User Manual Rev. 6 Page 13 of 18
DMX Channel Modes, Assignments, and Values
7-Channel
Channel Function Value Setting
1
Dimmer
000 ó255
0–100%
2
Warm White
000 ó255
0–100%
3
Cool White
000
ó
255
0–100%
4 Strobe
000 ó009
010 ó255
No function
0–20 Hz, slow to fast
5 Auto Program
000 ó051
052 ó101
102 ó152
153 ó203
204 ó254
255
No function
Auto program 1
Auto program 2
Auto program 3
Auto program 4
Auto program 5
6 Auto Program Speed 000 ó255
0–100%, slow to fast
(only when CH. 7 is between 052–255)
7 Dimmer Speed
000 ó051
052 ó101
102 ó152
153 ó203
204 ó255
Default dimmer speed
Linear dimmer
Non-linear dimmer 1
Non-linear dimmer 2
Non-linear dimmer 3
3-Channel
Channel Function Value Setting
1
Dimmer
000 ó255
0–100%
2
Warm White
000 ó255
0–100%
3
Cool White
000 ó255
0–100%
2-Channel
Channel Function Value Setting
1
Warm White
000 ó255
0–100%
2
Cool White
000 ó255
0–100%

Page 14 of 18 SlimPAR™ Pro VW User Manual Rev. 6
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
•Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode (Static or
Automatic) to a DMX string connected to a DMX controller. Product
s in standalone
mode may transmit DMX signals
that could interfere with the DMX signals from
the controller.
Automatic Mode
To enable the Automatic mode, follow the instructions below:
1. Press <MENU>repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the desired auto program, P--1–P--5.
4. Press <ENTER> and S00–S100 shows on the display.
5. Use <UP> or <DOWN> to select the auto program speed
S000–S100 (fast to slow).
6. Press <ENTER>.
Color
Temperature
Preset
Preprogrammed, static color temperature presets may be triggered without a controller,
as follows.
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the desired color temperature:
•C-01 - White 1, 2800 K
•C-02 - White 2, 3000 K
•C-03 - White 3, 3300 K
•C-04 - White 4, 3600 K
•C-05 - White 5, 4000 K
•C-06 - White 6, 4500 K
•C-07 - White 7, 5600 K
•C-08 - White 8, 6000 K
•C-09 - White 9, 6300 K
4. Press <ENTER>.
Custom Static
Color
To combine warm and cool white to create a custom, static color temperature mix
, follow
the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and AXXX (warm white), WXXX (cool white), or SXXX (strobe)
show on the display.
3. Use <UP> or <DOWN> to select the desired option and press <ENTER>.
•Use <UP> or <DOWN> to select the desired warm white color,
A000–A255 (0–100%).
•Use <UP> or <DOWN> to select the desired cool white color
W000–W255 (0–100%).
•Use <UP> or <DOWN> to select the desired strobe speed
S000–S020 (0–20 Hz).
4. Press <ENTER> to set selection and to go to the next option.
Dimming Curve
To combine warm and cool white to create a custom, static color temperature mix
, follow
the instructions below:
1. Press <MENU> repeatedly until dIM shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN>to select dIM1–dIM3 (small to large) or OFF(linear output).
4. Press <ENTER>.

SlimPAR™ Pro VW User Manual Rev. 6 Page 15 of 18
Master/Slave
Mode
The Master/Slave mode allows a single SlimPAR™ Pro VW
(the “master”) to control the
actions of one or more SlimPAR™ Pro VW
units (the “slaves”) without the need of a
DMX controller. The master will be set to operate in either an auto program or static
color, while the slaves will be set to operate in Slave mode. On
ce set and connected, the
slaves will operate in unison with the master.
Configure the units as indicated below.
The slaves:
1. Set the DMX starting address to 001.
2. Connect the DMX input of the first slave to the DMX output of the master.
3. Connect the DMX input of the subsequent slaves to the DMX output of the previous
slave.
4. Finish setting and connecting all the slaves.
The master:
1. Set the master unit to operate in either an auto program or static color.
2. Make the master unit the first product in the DMX daisy chain.
•Configure all the slaves before connecting the master to the DMX daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master.
•Do not connect more than 31 slaves to the master.

Page 16 of 18 SlimPAR™ Pro VW User Manual Rev. 6
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear.
To maintain optimum
performance and minimize wear, clean the product at least twice a month. However,
usage and environmental conditions contribute to increased cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is at room temperature.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all external optics and glass/transparent surfaces with a mild soap solution,
ammonia-free glass cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly wipe any dirt or grime to the outside edges of the external optics or
glass/transparent surface.
•Gently polish the external optics and glass/transparent surfaces until they are free of
haze and lint.
Always dry the external optics and glass/transparent
surfaces carefully after
cleaning them.

SlimPAR™ Pro VW User Manual Rev. 6 Page 17 of 18
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
3.4 in (87 mm)
10.1 in (256 mm)
11.2 in (285 mm)
6.3 lb (2.8 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
83 W
83 W
Operating current
0.6 A
0.4 A
Power linking current (units)
8 A (11 units)
8 A (18 units)
Fuse
F 2 A, 250 V
F 2 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
1 W
50,000 hours
Color
Quantity
Current
Cool white
18
350 mA
Warm white
18
350 mA
Photo Optic
Parameter
Illuminance @ 2 m
2,930 lx
Beam angle
21°
Field angle
42°
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
2, 3 or 7
Ordering
Product Name
Item Code
UPC Number
SlimPAR™ Pro VW
03030274
781462206222

Page 18 of 18 SlimPAR™ Pro VW User Manual Rev. 6
To return a product or request support:
•In the U.S., contact CHAUVET® World Headquarters (see below).
•In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•In any other country, DO NOT contact CHAUVET®. Contact your distributor. See
www.chauvetlighting.com for distributors outside the U.S., United Kingdom, Ireland,
or Mexico.
If you live outside the U.S., United Kingdom, Ireland, or Mexico
contact your
distributor of record and follow their
instructions on how to return CHAUVET®
products to them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET® Technical
Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product
. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid, in
its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write
the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are
recommended.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).
Contact Us
WORLD HEADQUARTERS - CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: t[email protected]om
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.co.uk
MEXICO - CHAUVET® Mexico
General Information/Información General
Address/ Av. Santa Ana 30
Dirección: Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice/Tel: [phone]
Technical Support/Servicio Técnico
Email: inf[email protected]om.mx
World Wide Web www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, or Mexico, contact your dealer. Follow their instructions
to request support or to return a product. Visit our website for contact details.