Chauvet ART-575W User manual

CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A
[phone] –[phone]
FAX [phone]
www.chauvetlighting.com
2006-06-15/17:08
ART-575W
Spectrum™575W
USER MANUAL

ART-575W User Manual 2 2006-06-15/17:08
TABLE OF CONTENT
TABLE OF CONTENT....................................................................................................................................................... 2
BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED .......................................................................................................................................................................................................... 3
UNPACKING INSTRUCTIONS.............................................................................................................................................................................................. 3
AC POWER ..................................................................................................................................................................................................................... 3
SAFETY INSTRUCTIONS.................................................................................................................................................................................................... 3
INTRODUCTION............................................................................................................................................................... 4
TECHNICAL FEATURES..................................................................................................................................................................................................... 4
FEATURES....................................................................................................................................................................................................................... 4
DMX CHANNEL SUMMARY ............................................................................................................................................................................................... 4
PRODUCT OVERVIEW....................................................................................................................................................................................................... 5
SETUP .............................................................................................................................................................................. 6
LAMP............................................................................................................................................................................................................................... 6
Lamp installation................................................................................................................................................................................................. 6
Lamp Alignment How-To.................................................................................................................................................................................... 7
POWER ........................................................................................................................................................................................................................... 7
INSTALLATION.................................................................................................................................................................................................................. 8
Orientation.......................................................................................................................................................................................................... 8
Floor Mounting.................................................................................................................................................................................................... 8
Truss Mounting................................................................................................................................................................................................... 8
Power configuration ................................................................................................................................................................................................. 9
Wiring the connector................................................................................................................................................................................................ 9
Data Cables & Linking ............................................................................................................................................................................................. 9
OPERATING INSTRUCTIONS........................................................................................................................................ 10
OPERATING MODES....................................................................................................................................................................................................... 10
Master/Slave & Stand-Alone ............................................................................................................................................................................ 10
Accessing internal programs in Master mode.................................................................................................................................................. 11
Built-in Programs chart..................................................................................................................................................................................... 12
DMX Mode........................................................................................................................................................................................................ 13
Setting the starting address .............................................................................................................................................................................13
APPENDIX...................................................................................................................................................................... 16
DMX PRIMER ................................................................................................................................................................................................................ 16
Fixture Linking .................................................................................................................................................................................................. 16
DMX CHANNEL VALUES ................................................................................................................................................................................................ 17
PHOTO METRICS ........................................................................................................................................................................................................... 18
DIPSWITCH LOCATION.................................................................................................................................................................................................... 19
MAINTENANCE............................................................................................................................................................................................................... 20
RETURNS PROCEDURE .................................................................................................................................................................................................. 20
CLAIMS ......................................................................................................................................................................................................................... 20
GENERAL TROUBLESHOOTING ....................................................................................................................................................................................... 21
TECHNICAL SPECIFICATIONS .......................................................................................................................................................................................... 22
TECHNICAL SUPPORT .................................................................................................................................................................................................... 22

ART-575W User Manual 3 2006-06-15/17:08
BEFORE YOU BEGIN
What is included
ART-575W –Spectrum™575W
(1) HSR575 HID lamp Power cord attached with bare ends Warranty Card & Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the
source voltage matches the fixture’s requirement. Check the fixture or device carefully to make sure
that if a voltage selection switch exists that it is set to the correct line voltage you will use.
Warning! Verify that the internal multi-tap transformer is set to match the line voltage applied. All
fixtures must be connected to circuits with a suitable Earth Ground.
Safety Instructions
Please keep this User Guide for future consultation. If you
sell the unit to another user, be sure that they also receive
this instruction booklet.
Always make sure that you are connecting to the proper
voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.
To prevent risk of fire or shock make sure there are no
flammable materials close to the unit while operating.
The unit must be installed in a location with adequate
ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
Always disconnect from power source before servicing or
replacing lamp or fuse and be sure to replace with same
lamp source.
Secure fixture to fastening device using a safety chain.
Never carry the fixture solely by its head. Use its carrying
handles.
Maximum ambient temperature is Ta: 50°. Do not operate
fixture at temperatures higher than this.
In the event of serious operating problem, stop using the
unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the
same type spare parts.
Don’t connect the device to a dimmer pack.
Make sure power cord is never crimped or damaged.
Never disconnect power cord by pulling or tugging on the
cord.
Avoid direct eye exposure to lamp while it is on.
Check your power cables carefully to ensure that
there are no cuts or breach of integrity of the outer
shell at any point. Moisture could be drawn up inside
the cable due to a vacuum generated by heat inside
the fixture.
Protect connectors for both power and data lines in a
weatherproof housing or a weatherproof junction
box.
If you don’t hard wire the fixture to a weatherproof
junction box, make sure to use an IP55 or better rated
connector for both plugs and connectors.
Do not connect to a dimmer system.
For your protection, the fixture must be grounded and
the AC mains supply must be outfitted with a circuit
breaker and ground-fault protection.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
CHAUVET.
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance?

ART-575W User Manual 4 2006-06-15/17:08
INTRODUCTION
Technical Features
8-channel DMX-512 exterior color wash
CMY color mixing system
Vectored movement of all color blades for super smooth and slow transitions
11 instantly selectable preset color macros
Variable mechanical dimmer (0 ~ 100%)
Variable mechanical zoom (7°~40°)
32 built in color change programs at varying speeds
Features
Durable and weatherproof IP-54 rated housing
Very low noise operation (convection cooled) <- look for a fan??
No control necessary, Master/Slave operation
Frosted lens diffuser
Micro-stepping motors
Thermal switch protection
DMX Channel Summary
CHANNEL FUNCTION
1 Vector speed
2 Yellow
3 Magenta
4 Cyan
5 Color Macros
6 Dimmer
7 Zoom
8 Automatic

Introduction
ART-575W User Manual 5 2006-06-15/17:08
126
4
4
6
410
4
4
5
.
7
289.2
Front View
Side View
5
2
8
11.38in
17.6in
16.1in
17.5in
Top View
20.8in
4
2
8
2
8
9
.
2
326
396
80
150
344
254
100 100
Bottom View
16.9in
13.5in
12.8in
11.4in
5.9in
3.15in
10.0in
3.9in
15.6in
Projection angle
Carrying handles
Product Overview

ART-575W User Manual 6 2006-06-15/17:08
Followthisdirectionto open cover
Besuretodisconnectunitfrompowerbefore
Changinglampsoropeningtheunitcover.
Lampbecomeshotduringoperation.allowtime
(atleast 15mi nutes)to cool bef ore handing.donot
Lookdirectlyatlampwhenlit.
Warning!
INSIDE
POWER SWITCH
ON
OFF
AB
C
D E
RemovethelampcoverbyturningscrewsD& E
TurnscrewsA,B& Canti-clockwise to
reduce thediameterofthelightbeam.
TurnscrewsA,B & Cclockwiseto increase
the diameterofthelight beam.
Turn screw Ct oadjust vertical posi tion.
Turn screwsA& B toadjust horizontal posi tion.
A B
D E
C
Back cover plate
Lamp plate
AB
D E
C
Lamp plate
Remove these
screws to
install or
replace lamp
SETUP
Lamp You will need to install a lamp prior to the initial operation of the fixture.
Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit
to cool down! Always disconnect from main power prior to lamp replacement.
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
with alcohol and wipe it with a lint free cloth before installation.
LAMP INSTALLATION
1) Remove the back cover plate by removing all 8 screws on the rear of the fixture.
2) Remove the screws (D) and (E) on the lamp plate. Pull out the lamp cover plate.
3) With lamp socket plate out and the lamp accessible, if replacing the lamp, remove old lamp first.
4) Holding the new lamp by its base, align the small pin
on the lamp with the small hole in the socket and insert
the lamp squarely until the retaining clips on the lamp
socket secures the lamp tightly.
5) Clean the glass/envelope of the bulb with an alcohol
wipe or equivalent.
6) Holding the lamp plate, insert the tip of the lamp into
the fixture with extreme care. Navigate the lamp all the
way until it reaches the reflector and the lamp base
plate touches the bottom plate of the fixture.
7) Align the screw holes and fasten the screws back onto
the lamp plate.
8) Turn the fixture on and adjust the lamp alignment screws until the brightest most even area of the
beam is in the center of your spot. It may be necessary for you to use a controller in order to
command the fixture to display a white beam. Visit the “Lamp Alignement How-To”section in this
manual for further reading and tips on the subject.
9) Place the back cover plate back on the fixture and screw on securely.

Setup
ART-575W User Manual 7 2006-06-15/17:08
AB
D E
C
Lamp Alignment Screws, A, B & C
100V
100V
115V
115V
208V
208V
230V
230V
240V
240V
50Hz
50Hz60HzININ
60Hz
Select voltage
To Ballast 230V/50Hz
To Ballast 230V/60Hz
Lamp Control to PCB in
AC-100-230V
INPUT
To TRANSFORMER
LAMP ALIGNMENT HOW-TO
Often, after a new installation of a lamp, you will find that there is an uneven field of light or what is
referred to as a hot spot. This is due to the most intense point of the lamp source not being positioned
optimally within the reflector.
There are three lamp alignment screws provided at the base of the projector head, behind the back
cover plate. Turning these screws allow you to
optimize the projection quality of the spot as well
as the overall intensity of the beam.
1. Project a white flood against any flat surface.
Preferably the surface should be white or
pastel in color.
2. Turning the lamp alignment screws, try to
position the hot spot in the center of the beam
as best as possible. This could require many
attempts on your part.
3. Once the hot spot is in the center of the spot,
do your best to turn all screws equally as to
affect movement up or down within the reflector.
4. As you move in and out of optimum lamp focus, you will see the hot spot either gets wider or
narrower. The goal is to either totally diminish the hot spot by having it widen and spread across
the entire spot or moving the hot spot so that it covers as much of the beam spot area as possible.
Power
Warning! Verify that the internal multi-tap transformer is set to match the line voltage applied and
that the proper fuse is installed for the appropriate voltage setting. All fixtures must
be connected to circuits with a suitable Earth Ground.
To determine the power requirements for
a particular fixture, see the label affixed
to the back plate of the fixture or refer to
the fixture’s specifications chart.
A fixture’s listed current rating is its
average current draw under normal
conditions.
All fixtures must be powered directly off a
switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100%
switch.
Before applying power to a fixture, check
that the source voltage matches the
fixture’s requirement.
All fixtures must be connected to circuits with a suitable Earth Ground.
POWER CABLE PIN INTERNATIONAL
BROWN Live L
BLUE Neutral N
YELLOW/GREEN Earth EG (Ground)
OPERATING VOLTAGE MUST USE CORRECT FUSE
120V 15A
230V 10A
CAUTION!
This lighting
fixture comes
from the
factory with a
120V fuse pre-
installed. To
operate this
fixture in 230V,
please replace
the external
fuse with the
supplied 230V
fuse.
CAUTION!
Voltage selector switch is
accessible by removing the
front cover of the fixture.
Re-wiring of the transformer
should be conducted by a
certified electrician or
lighting professional.

Setup
ART-575W User Manual 8 2006-06-15/17:08
126
Floor mount
Clamp
Bas
e
Installation
ORIENTATION
This fixture is designed to achieve an Ingress Protection Rating of 54 only when the fixture’s base is
attached to a level horizontal surface. The ART-575W can be mounted both upright and on a truss
system.
Warning
It is important never to obstruct the fan or vents pathway.
When selecting installation location, take into consideration lamp replacement access and routine
maintenance.
Safety cables should always be used.
The fixture must have a minimum of 1 meter distance from combustible materials.
FLOOR MOUNTING
1) If connected, be sure to always disconnect from main power before installing fixture.
2) The ART-575W is constructed with mounting bracket/yoke.
3) Bolt fixture onto a leveled floor surface using floor mount holes and 3/8”diameter bolts.
TRUSS MOUNTING
The ART-575W includes 3 clamp
mounting brackets to which half-
coupler pipe clamps can be bolted.
1) Verify the structure can hold 10
times the weight of all fixtures to-be
installed.
2) Attach a minimum of two to three
clamps where illustrated.

Setup
ART-575W User Manual 9 2006-06-15/17:08
Power configuration
The factory power settings will be printed on the fixtures serial label. Make sure that your local AC
voltage matches that required by the fixture.
115V / 50Hz AC
230V / 60Hz AC
The ART-575W is equipped with a 3-conductor electrical cable for connecting to an AC power supply.
The cable enters the fixture through a cable gland that fits 5 to 10mm diameter cables. Because the
ART-575W fixture is built for permanent exterior installations please adhere to the following safety
and installation precautions.
SAFETY PRECAUTIONS!
Check your power cables carefully to ensure that there are no cuts or breach of integrity of the
outer shell at any point. Moisture could be drawn up inside the cable due to a vacuum generated
by heat inside the fixture.
Protect connectors for both power and data lines in a weatherproof housing or a weatherproof
junction box.
If you don’t hard wire the fixture to a weatherproof junction box, make sure to use an IP54 or better
rated connector for both plugs and connectors.
Do not connect to a dimmer system.
For your protection, the fixture must be grounded and the AC mains supply must be outfitted with a
circuit breaker and ground-fault protection.
Wiring the connector
Visible Markings (USA) Wires (EU) Wires Connector
Live “L”Black Brown Yellow or brass
Neutral “N”White Blue Silver
Ground “W”Green Yellow/Green Green
Consult an electrician if you have any doubts about the proper wiring connection during your
installation.
Data Cables & Linking
Data linking is required for synchronized operation as well as DMX controller operation. The ART-
575W fixture is equipped with two 24 AWG data cables that exit the fixture through a cable gland.
Both cables are equipped with XLR connectors. The locking 3-pin male is for data input and the 3-pin
female is for data output. The “DMX Primer”in the Appendix section details more information about
wiring. In short, a 3-pin connector is wired pin-1 to (ground), pin-2 to (signal) and pin-3 to (hot).
Use RS-485 data cables designed for outdoor use.
(24 AWG) for runs up to 1000 feet or 300 meters
(26 AWG) for runs up to 1640 feet (500 meters)
Currently, neither the data cables nor the power cable is weather rated. Consider changing these for
exterior weather rated equivalents. In addition, follow the same “Safety Precautions”as listed in the
section above “Power configuration”.
Tips!
oUse shielded twisted-pair cable designed for RS-485 devices.
oNever use a “Y”connector to split the link. To split the serial link into branches use an Opto-Isolated signal
splitter.
oLimit one universe of DMX-512 to no more than 32 devices.
oUse a terminator at the end of a run. A terminator can be made by soldering a 120ohm, 0.25 watt resistor
between pins 2 and 3 of a male XLR connector.

ART-575W User Manual 10 2006-06-15/17:08
Daisy Chain
Connection
also
applies to DMX-512 control.
ON
1
2 3
4
5 6 7 8 9 10 11
12
MASTER
SLAVE
ON
1
2 3
4
5 6 7 8 9 10 11
12
ON
1
2 3
4
5 6 7 8 9 10 11
12
Dip 11 = ON
Dip 12 = OFF
Dip 11 = OFF
Dip 12 = ON
Dip 11 = OFF
Dip 12 = ON
DMX Cable
OPERATING INSTRUCTIONS
Operating Modes
Stand-Alone mode will allow the independent execution of programs and a Master/Slave mode will
allow the command of up to as many units you want in a synchronized manner.
DMX control mode will provide the greatest flexibility and creativity. You can create an unlimited
range of chase patterns at any speeds
MASTER/SLAVE & STAND-ALONE
Stand-alone is an independent fixture operating state which basically means without the use of any
controlling device. The Spectrum™575 Exterior Wash fixtures have 42 internal programs that can be
manually selected using the fixture’s dipswitches. Once set, every time the fixture is powered, the
program selected will automatically execute. If you own multiple Spectrum™fixtures, you can link
them together so that they all follow one leader in synchrony called the (master). This operating state
is called Master/Slave mode.
The Master/Slave mode allows you to link multiple units in a daisy chain fashion. In this mode, the
first unit in the daisy chain will automatically command all other units following. Simply connect each
fixture in a daisy like fashion using qualified 3 pin DMX cables and address master and slave fixtures
as described below. The first unit in the chain will operate in a Stand-Alone mode and all units
following will synchronize to the first unit.
1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of
the first fixture.
2) Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector
to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to
connect from the output as stated above to the input of the following fixture and so on as illustrated
below in “Daisy Chain Connection”.