Chauvet Scorpion 3D RGB User manual

User Manual
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS IIIa LASER PRODUCT
CLASSIFIED PER 21 CFR 1040.10 & .11
Complies with U.S. FDA CDRH laser safety
standards 21 CFR 1040.10 & 1040.11.

Page 2 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
TABLE OF CONTENTS
1. Before You Begin ...........................................................................................................5
What Is Included ........................................................................................................................5
Claims .......................................................................................................................................5
Text Conventions.......................................................................................................................5
Symbols.....................................................................................................................................5
Disclaimer..................................................................................................................................5
Safety Notes ..............................................................................................................................6
Non-Interlocked Housing Warning ........................................................................................................7
Laser Safety Notes...............................................................................................................................7
Laser Safety Label Reproduction ...............................................................................................8
Laser Exposure Warning......................................................................................................................9
Laser Emission Data .................................................................................................................9
2. Introduction ..................................................................................................................10
Overview..................................................................................................................................10
Dimensions..............................................................................................................................11
3. Setup.............................................................................................................................12
AC Power ................................................................................................................................12
Fuse Replacement...................................................................................................................12
Power Linking....................................................................................................................................13
Mounting..................................................................................................................................14
Orientation.........................................................................................................................................14
Rigging..............................................................................................................................................14
Proper Usage.....................................................................................................................................15
4. Operation ......................................................................................................................16
Control Panel Operation...........................................................................................................16
Changing Options Within the Same Function ......................................................................................16
Changing Options for a Different Function...........................................................................................16
Menu Map................................................................................................................................16
Configuration (DMX) ................................................................................................................16
Starting Address ................................................................................................................................16
DMX Channels.........................................................................................................................17
Configuration (Standalone).......................................................................................................18
Sound-Active Mode............................................................................................................................18
Automatic Mode.................................................................................................................................18
Master/Slave Mode ............................................................................................................................18
Remote Control........................................................................................................................19
5. Technical Information ..................................................................................................20
Product Maintenance ...............................................................................................................20
6. Technical Specifications..............................................................................................21
1. Antes de Empezar ........................................................................................................22
Qué va Incluido........................................................................................................................22
Reclamaciones .........................................................................................................................22
Convenciones de Texto............................................................................................................22
Símbolos..................................................................................................................................22
Exención de Responsabilidad ...................................................................................................22
Notas de Seguridad .................................................................................................................23
Advertencia Sobre Carcasa no Cerrada..............................................................................................24
Notas de Seguridad Sobre Láser........................................................................................................24
Reproducción de la Etiqueta de Seguridad del Láser................................................................26
Advertencia Sobre Exposición al Láser...............................................................................................27

Scorpion™ 3D RGB User Manual (Rev. 3) Page 3 of 60
Datos de Emisión Láser ...........................................................................................................27
2. Introducción .................................................................................................................28
Vista General ...........................................................................................................................28
Dimensiones............................................................................................................................29
3. Instalación ....................................................................................................................30
Corriente Alterna......................................................................................................................30
Sustitución del Fusible .............................................................................................................30
Alimentación en Cadena ....................................................................................................................31
Montaje....................................................................................................................................32
Orientación........................................................................................................................................32
Colocación.........................................................................................................................................32
Uso Adecuado ...................................................................................................................................33
4. Funcionamiento............................................................................................................34
Funcionamiento del Panel de Control .........................................................................................34
Cambiar Opciones Dentro de la Misma Función..................................................................................34
Cambiar Opciones para una Función Diferente ...................................................................................34
Mapa de Menú.........................................................................................................................34
Configuración (DMX)................................................................................................................35
Dirección de Inicio..............................................................................................................................35
Canales DMX...........................................................................................................................36
Configuración (Independiente) .................................................................................................37
Modo Activo por Sonido .....................................................................................................................37
Modo Automático...............................................................................................................................37
Modo Maestro/Esclavo.......................................................................................................................37
Control Remoto........................................................................................................................38
5. Información Técnica ....................................................................................................39
Mantenimiento del Producto.....................................................................................................39
6. Especificaciones Técnicas..........................................................................................40
Devoluciones ...........................................................................................................................41
Contacto ..................................................................................................................................41
1. Avant de Commencer...................................................................................................42
Ce qui est Compris...................................................................................................................42
Réclamations ...........................................................................................................................42
Conventions de Texte ..............................................................................................................42
Symboles.................................................................................................................................42
Clause de non Responsabilité..................................................................................................42
Consignes de Sécurité .............................................................................................................43
Avertissement: Boîtier non Verrouillable.............................................................................................. 44
Consignes de Sécurité Relatives au Laser..........................................................................................44
Avertissement d'Exposition au Laser...................................................................................................47
Données d'Emission Laser.....................................................................................................47
2. Introduction ..................................................................................................................48
Aperçu.....................................................................................................................................48
Dimensions..............................................................................................................................49
3. Configuration................................................................................................................50
Alimentation CA .......................................................................................................................50
Remplacement du Fusible........................................................................................................50
Connexion Electrique.........................................................................................................................51
Installation ...............................................................................................................................51
Orientation.........................................................................................................................................51
Suspension........................................................................................................................................51
Utilisation Adéquate ...........................................................................................................................52

Page 4 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
4. Fonctionnement ...........................................................................................................53
Fonctionnement du Panneau de Commande ..............................................................................53
Changer d'Options au Sein d'une Même Fonction ...............................................................................53
Changer d'Options au Sein d'une Fonction Différente..........................................................................53
Tableau du Menu.....................................................................................................................53
Configuration (DMX) ................................................................................................................54
Adresse de Départ .............................................................................................................................54
Canaux DMX ...........................................................................................................................55
Configuration (Autonome) ........................................................................................................56
Mode Musical.....................................................................................................................................56
Mode Automatique.............................................................................................................................56
Mode Maître/Esclave.......................................................................................................................... 56
Télécommande ........................................................................................................................57
5. Informations Techniques.............................................................................................58
Entretien de l'Appareil ..............................................................................................................58
6. Spécificités Techniques...............................................................................................59
Returns....................................................................................................................................60
Contact Us...............................................................................................................................60

Scorpion™ 3D RGB User Manual (Rev. 3) Page 5 of 60
1. BEFORE YOU BEGIN
What Is
Included
•Scorpion™ 3D RGB
•Power Cord
•Infrared Remote Control (IRC)
•Warranty Card
•Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make sure all the parts
are in the package and are in good condition.
If the box or the contents (the product and
included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as
missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Convention
Meaning
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol
Meaning
Critical installation, configuration, or operation information.
Ignoring this information can cause the product to not work,
damage it, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual
are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual, and reserves the right to revise or recreate
this manual at any time. Download the latest version from www.chauvetlighting.com.
© Copyright 2012 CHAUVET®. All rights reserved.
Printed in P.R.C.
Electronically published by CHAUVET® in the United States of America.
Author
Date
S. Diaz 10/29/12

Page 6 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
Safety Notes
The Safety Notes include
important laser system safety information. Read and
understand all instructions before powering on the laser for the first time.
Knowing these safety instructions is crucial to avoiding
laser eye injury and
breaking the law. Keep this user manual in a safe place for future reference.
STOP AND READ ALL LASER SAFETY DATA
•CAUTION! Viewing laser light directly (intra-beam viewing) through optical
instruments, such as cameras and binoculars, may increase risks to the eyes.
•Lasers can be hazardous and have unique safety considerations. Permanent
eye injury and blindness is possible if lasers are used incorrectly. Pay close
attention to each safety REMARK and WARNING statement in this User
Manual. Read all instructions carefully BEFORE operating this device.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from power before cleaning it or replacing the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a safety
cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•This product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Always use the mounting bracket to carry the product.
•Do not switch the product on/off in short intervals. This will reduce the laser diode life.
•Do not shake this product. Avoid brute force when mounting or operating this product.
•ALWAYS use a safety cable when mounting the product overhead.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•Avoid direct eye contact with laser light. Never intentionally expose your eyes or
others to direct laser light.
•This laser product can potentially cause instant eye injury or blindness if laser light
directly strikes the eyes.
•It is illegal and dangerous to shine this laser into audience areas, where the
audience or other personnel could get direct laser beams or bright reflections into
their eyes.
•It is a U.S. federal offense to shine any laser at aircraft.
•Use of controls, adjustments, or procedures other than those specified herein may
result in hazardous radiation exposure.
•DO NOT attempt any repairs. Repairs and servicing must be carried out by a
certified technician. Unauthorized modifications are forbidden for safety
reasons!
•Keep this User Manual for future consultation. If transferring ownership of the
product to another user, be sure this document is kept with the laser.

Scorpion™ 3D RGB User Manual (Rev. 3) Page 7 of 60
Non-Interlocked
Housing Warning
•This unit contains high power laser devices internally.
•Do not open the laser housing, due to potential exposure to unsafe levels of laser
radiation.
•
The laser power levels, accessible if the unit is opened, can cause instant blindness,
skin burns, and fires.
Laser Safety
Notes
STOP AND READ ALL THE LASER SAFETY NOTES BELOW
Laser light is different from any other light sources. The light from this product can
potentially cause eye injury if the product is
not set up and used properly. Laser light is
thousands of times more concentrated than light from any other kind of light source. This
concentration of light can cause instant eye injuries, primarily b
y burning the retina (the
light-sensitive portion at the back of the eye). Even if you cannot feel “heat” from a laser
beam, it can still potentially injure
or blind you or your audience. Even very small
amounts of laser light are potentially hazardous—
even at long distances. Laser eye
injuries can happen faster than you can blink.
DO NOT assume that because some laser entertainment products split the laser into
hundreds of beams and/or that the laser beam is scanned out in high speed, that any
individual laser beam is safe for eye exposure. This type of laser product may use
dozens of milliwatts of laser power(Class 3B levels) internally or before it splits into
multiple beams (Class IIIa levels). Many of the individual beams are potentially
hazardous to the eyes.
DO NOT assume that because the laser light is moving, it is safe. Laser light is never without
risk, nor do the
laser beams always move. Since eye injuries can occur instantly, it is critical
to prevent the possibility of ANY direct eye exposure. According to laser safety regulations
, it
is not legal to aim Class IIIa lasers in areas where people can get exposed. This is true even
if the laser is aimed below people’s faces, such as on a dance floor.
•Do not operate the laser without first reading and understanding all safety and
technical data in this manual.
•ALWAYS set up and install all laser effects so that all laser light is at least 3 meters
(9.8 feet) above the floor on which people can stand.
•After set up, and prior to public use, test laser to ensure proper function. Do not use
if any defect is detected.
•DO NOT use laser if the laser lens is damaged or missing, as this could indicate
damage to the diffraction grating optic, and could allow emission of laser levels
higher than Class IIIa.
•DO NOT point lasers at people or animals.
•NEVER look into the laser aperture or laser beams.
•DO NOT point lasers in areas in which people can potentially get exposed, such as
uncontrolled balconies, etc.
•DO NOT point lasers at highly reflective surfaces, such as windows, mirrors, and
shiny metal. Even laser reflections can be hazardous.
•NEVER point a laser at aircraft; this is a U.S. federal offense.
•NEVER point un-terminated laser beams into the sky.
•Do not expose the output optic (aperture) to cleaning chemicals.
•Do not use the laser if the housing is damaged, open, or if the optics appear
damaged in any way.
•NEVER open the laser housing. The high laser power levels inside of the protective
housing can start fires or burn skin, and will cause instant eye injury.
•Never leave this product running unattended.
•The operation of a Class IIIa laser show is only allowed if the show is controlled by a
skilled and well-trained operator, familiar with the data included in this manual.
•The legal requirements for using laser entertainment products vary from country to
country. The user is responsible for the legal requirements in the location/country of
use.
CAUTION! DO NOT operate this device in ways not specified in this User Manual. Failure to follow
the instructions will void the warranty, may damage the product, or injure the user or the audience.
CAUTION! This product cannot be discarded with household waste. Contact your local waste
management service for electronic disposal regulations in your area.

Page 8 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
Laser Safety Label Reproduction
EXPLANATORY,
MANUFACTURER’S ID &
CERTIFICATION LABEL
LASER HAZARD
WARNING LABEL
LASER APERTURE
NOTIFICATION LABEL
NON-INTERLOCKED HOUSING
WARNING LABEL

Scorpion™ 3D RGB User Manual (Rev. 3) Page 9 of 60
Laser
Exposure
Warning
LASER LIGHT! AVOID DIRECT EYE EXPOSURE
Further guidelines and safety programs for safe use of lasers can be found in the ANSI
Z136.1 Standard “For Safe Use of Lasers”, available from the Laser Institute of America:
www.laserinstitute.org. Many local governments, corporations, agencies, military, and
others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display
guidance can be obtained via the International Laser Display Association:
www.laserist.org.
Laser
Emission
Data
Laser
Compliance
Statement
This laser product complies with U.S. FDA CDRH laser safety standards 21
CFR 1040.10 & 1040.11. This laser device is classified Class IIIa. No
maintenance is required to keep this product in compliance with laser
performance standards.
Laser Classification
Class IIIa
Red Laser Diode
LD GaAIAs 650 nm, typical
Green Laser Diode
DPSS Nd:YVO4, 532 nm
Blue Laser Diode
LD GaN 450 nm, typical
Beam Diameter
<5 mm at aperture
Pulse Data
100 msec to CW (continuous)
Divergence (each)
<2 mrad
Scan Angle
<160 degrees
Peak Power for
Classification
<5 mW

Page 10 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
2. INTRODUCTION
Overview
Cooling Fan
Display Panel
Safety Loop
Power In/Out
DMX In/Out
Fuse Holder
Power Switch
Bracket Adjustment Knob
Mounting Bracket
Laser Aperture

Scorpion™ 3D RGB User Manual (Rev. 3) Page 11 of 60
Dimensions

Page 12 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
3. SETUP
AC Power
The Scorpion™ 3D RGB has an auto-
ranging power supply and it can work with an input
voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker,
power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse).
Make sure the product has
an appropriate electrical ground to avoid the
risk of electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer
circuit, even if the rheostat or dimmer channel serves only as a 0~
100%
switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
Always replace a blown fuse with a fuse of the same type and rating.
1. Unplug the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
The product does not ship with a spare fuse; however, the safety cap has
room for a spare.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Scorpion™ 3D RGB User Manual (Rev. 3) Page 13 of 60
Power Linking
The product provides power linking via the
IEC outlet located in the back of the unit.
Please see the diagram below.
Power Linking
Diagram
You can power link up to 31 Scorpion™ 3D RGB unit
s on 120 VAC or up to
52 Scorpion™ 3D RGB units on 230 VAC.
The power linking diagram shown above corresponds to the North
American version of the product ONLY! If using the product
in other
markets, consult with the local CHAUVET® distributor as power linking
connectors and requirements may differ in your country or region.
1st Product
2nd Product
3rd Product
Other
products

Page 14 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Scorpion™ 3D RGB must be mounted in a position
that includes planning for safe
laser usage; in addition, make sure adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access
to the product for maintenance and programming.
•Make sure that the structure or surface onto which you are mounting the product can
support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable. Mount the product
securely to a rigging point, such as an elevated platform or a truss.
•When rigging the product onto a truss, use a mounting clamp
of appropriate weight
capacity.
•When power linking multiple product
s, always consider the length of the power
linking cable and mount the products close enough for the cable to reach.
•The bracket adjustment
knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs by hand.
Using tools could damage the knobs.
Clamp
Mounting Bracket
Bracket
Adjustment Knob
Safety Cable/Safety Loop

Scorpion™ 3D RGB User Manual (Rev. 3) Page 15 of 60
Proper Usage
This product is for overhead mounting only. For safety purposes, CHAUVET®
recommends mounting lighting effect products on steady elevated platforms or sturdy
overhead supports using suitable hanging clamps. In all cases, use safety cables.
Obtain appropriate mounting hardware from your lighting vendor.
International laser safety regulations require that laser products must be operated
in the fashion illustrated below, with a minimum of 3 meters (9.8 ft) of vertical
separation between the floor and the lowest laser light vertically. Additionally, 2.5
meters of horizontal separation is required between laser light and audience or
other public spaces.
CAUTION! USE OF CONTROLS, ADJUSTMENTS, OR PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.

Page 16 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
4. OPERATION

This product is not designed for continual use. Make sure there are
regular breaks during operation to maximize the life of your laser.
Always disconnect the Scorpion™ 3D RGB from power when not in use.
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. When the product is on, the display
on the rear panel will show the current
operating mode (standalone or DMX). The product will retain the last saved settings when
powered off.
Button
Function
<MENU> Selects an operation mode or backs out of the current menu option
<UP>
Scrolls up the list of options or selects a higher value
<DOWN>
Scrolls down the list of options or selects a lower value
<ENTER> Activates a menu option or a selected value
Changing
Options Within
the Same
Function
To change an option, do the following:
1. Press <MENU> once (the LED display will blink).
2. Press <UP> or <DOWN> until the desired menu option shows on the LED display.
3. Press <ENT> to accept the new option (the new option will show solid on the LED
display).
Changing
Options for a
Different
Function
To change an option for a different function:
1. Press <MENU> once (the LED display will blink).
2. Press <MENU> repeatedly until seeing the active option of the desired menu branch.
3. Press <UP> or <DOWN> until the desired menu option within the new menu branch
shows on the LED display.
4. Press <ENT> to accept the new option (the new option will show solid on the LED
display).
Menu Map
Mode or
Starting Value
Program or
Channel Range
Options Description
Standalone
Aut
Pre-programmed effects that cannot be customized
Aut
N/A
Automatic (Random)
Sound-Active
Sensitivity
The product responds to the beat of the music
Sou
S 0~S 9
0 = least sensitive, 9 = most sensitive
DMX
000~495
N/A
DMX mode, sets starting address
SLA
For Master/Slave operation
S = ˧
Image orientation
rEn
Remote control operation
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
on the Scorpion™ 3D RGB.
Starting Address
When selecting a DMX
starting address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting
address that is too high, you could
restrict the access to some of the product’s channels.
The Scorpion™ 3D RGB uses up to 18 DMX channels in its
DMX mode, which defines
the highest configurable address to 495. If you are not familiar with DMX, download the
DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>repeatedly until a three-digit value appears on the display.
2. Use <UP> or <DOWN> to select the starting address.
3. Press <ENTER>.

Scorpion™ 3D RGB User Manual (Rev. 3) Page 17 of 60
DMX Channels
Channel Value Function
1 Mode
000~085
DMX mode
086~170
Mixed effects auto show
171~255
Sound-Active mode
2 Group
000~051
1 Group Patterns
052~103
2 Group Patterns
104~155
3 Group Patterns
156~207
4 Group Patterns
208~255
5 Group Patterns
3 Pattern
000~255
Every 16 for 1 Group, total 16 patterns
4 Color
000
Blackout
001~007
Original
008~015
Red
016~023
Green
024~031
Yellow
032~039
Blue
040~047
Purple
048~055
Light Blue
056~063
White
064~111
Color Rolling
112~159
Color Jumping
160~127
Color Moving
208~255
Strobing Slow to Fast
5 Clipping
000
Full Pattern without clipping
001~127
0~99% Fixed Pattern clipped
128~255
Clipping speed
6 Zoom
000~127
100%~5% Fixed Pattern zoomed
128~169
Zoom IN
170~209
Zoom OUT
210~255
Alternately Zooming
7 Zoom Speed
000~255
Fast to Slow Zoom Speed
8 Y-Axis Rotation
000~127
0~359° fixed Y-Axis rotation
128~91
Clockwise rotation
192~255
Counterclockwise rotation
9 Y-Axis Speed
000~255
Fast to Slow Y-Axis rotation Speed
10 X-Axis Rotation
000~127
0~359° Fixed X-Axis rotation
128~191
Clockwise rotation
192~255
Counterclockwise rotation
11 X-Axis Speed
0~255
Fast to Slow Roll Speed
12 Z-Axis Rotation
000~127
0~359° Fixed Z-Axis rotation
128~191
Clockwise rotation
192~255
Counterclockwise rotation
13 Z-Axis Speed
000~255
Fast to Slow Z-Axis Rotation Speed
14 X-Axis Pan
000~127
128 Different fixed positions on the X-Axis
128~191
Clockwise panning
192~255
Counterclockwise panning
15 X-Axis Speed
000~255
Fast to Slow X-Axis Moving
16 Y-Axis Tilt
000~127
128 Different fixed positions on the Y-Axis
128~191
Clockwise tilting
192~255
Counterclockwise tilting
17 Y-Axis Speed
000~255
Fast to Slow Y-Axis tilting
18 Pattern Rotation
000~004
No pattern rotating
005~127
Clockwise pattern rotating
128~133
No pattern rotating
134~255
Pattern rotating

Page 18 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either
Static, Automatic, or Sound)
to a DMX string connected to a DMX
controller. Product
s in standalone mode may transmit DMX signals that
could interfere with the DMX signals from the controller.
Sound-Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU repeatedly until Sou or Aut shows on the display.
2. Press <UP> or <DOWN> until Sou shows on the display.
3. Press <ENTER>.
4. Turn the music on and press <MENU> until S 0(~9) shows on the display.
5. Use <UP> or <DOWN> to set the sound sensitivity from level S 1~S 9, with S 9
being the most sensitive.
6. Press <ENTER>.
The product will only respond to low frequencies of
music (bass and
drums).
The laser will BLACKOUT when in Sound-Active mode after 3 seconds of
silence or noise below the sensitivity setting.
Individual products have different sound sensitivities, even when set to
same number. For the best results, use Master/Slave mode to make all
products operate in unision to the beat of the music.
Automatic Mode
To enable the Automatic mode, follow the instructions below:
1. Press <MENU repeatedly until Sou or Aut shows on the display.
2. Press <UP>or <DOWN> until Aut shows on the display.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select the desired effect for an automatic program.
5. Press <ENTER>.
Master/Slave
Mode
The Master/Slave mode allows a single Scorpion™ 3D RGB product (the “master”) to
control the actions of one or more Scorpion™ 3D RGB products (the “slaves”) without
the need of a DMX controller. The master will be set to operate in either Automatic or
Sound Active mode, while the slaves will be set to operate in Slave mode. Once set and
connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU>repeatedly until SLA shows on the display.
2. Press <ENTER> to accept.
3. Connect the DMX input of the first slave unit to the DMX output of the master unit.
4. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
5. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Sound-Active mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure all the slave units before connecting the master unit to the
DMX daisy chain.
•
Never connect a DMX controller to a DMX string configured for
Master/Slave operation because the controller
may interfere with the
signals from the master unit.
•
Do not connect more than 31 slave units to the master unit.

Scorpion™ 3D RGB User Manual (Rev. 3) Page 19 of 60
Remote Control
Button Function Description
ON/OFF Holding for 3 seconds will activate or deactivate remote mode, so
that the laser can be powered on or off with the remote
AUTO MODE Laser runs on built-in automated programs
SOUND-ACTIVE
MODE
The music LED indicator is flashing when sound signal is detected
SOUND
SENSITIVITY
In Sound-Active Mode, press MUSIC + B + “1~9” to adjust sensitivity
setting, “9” is the most sensitive
COLOR
CHANGING Selects laser color: Red>Green>Blue>R&G>G&B>B&R>RGB
PATTERN
CHANGING Press A/C and then a number (0~9) to select the desired pattern
PATTERN SPEED No function
PATTERN SWAP Pattern effect that swaps between the last two patterns selected
Turn the
Laser On/Off
Pattern Swap
Sound Sensitivity
Effect Pause
Color Changing
Auto Mode
Sound-Active Mode
Fixed Pattern
(From 1 to 24)
Changing Pattern

Page 20 of 60 Scorpion™ 3D RGB User Manual (Rev. 3)
5. TECHNICAL INFORMATION
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. To maintain
optimum
performance, clean the product at least twice a month. Note: Use and
environmental conditions may contribute to increasing the cleaning frequency.
To clean the product:
•Unplug the product from power.
•Wait until the product is room temperature.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean the glass surfaces with a mild soap solution, ammonia-free glass cleaner, or
isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly wipe any dirt or grime to the outside edges of the glass surface.
•Gently polish the glass surfaces until they are free of haze and lint.
Always dry transparent surfaces carefully after cleaning them.
Do not spin the cooling fan using compressed air
because you could
damage it.