Chef-Master GH Series User manual

Chefmaster Crepe Maker
Instruction Manual
Models
HEF572 –Crepe Maker 400MM Dia.

2
Thank you for purchasing your Chefmaster Crepe Maker. To make full
use of the product please read this manual carefully before using the
product and keep it safe for future reference.
Safety Tips
•If you find any damage when the product is unpacked, contact your
Chefmaster supplier within 24 hours of receipt of goods
•Always position on a flat stable surface
•Repairs should always be carried out by a qualified technician
•Do not use this product outside
•Do not carry when hot
•Always switch off and unplug the unit before cleaning
•Move by holding the product by the base
•Always store flat and do no store products on top of it
•If the power cord becomes damaged it must be replaced by a qualified
technician
•This product is not designed to be used by persons with reduced
physical or mental capabilities, lack of experience or knowledge, unless
they are given suitable supervision, this includes children.
Pack Contents
•1 x Chefmaster Crepe Maker
•1 x Wooden Spreader
Before Use
•Remove all packaging including all protective plastic, from your
Chefmaster Crepe Maker
•Clean the unit with soft damp cloth
•Position on a flat surface
•Plug your Chefmaster Crepe Maker into the mains
•The unit is now ready to turn on
Operation
•Ensure the Crepe Maker is plugged in and the power is on
•Select the temperature you require, the heating indicator light will be on
•The power will cut off automatically when the set temperature has
reached. The heating light will cycle on and off during use
•Switch off the unit & unplug after use

3
Cleaning & Maintenance
•Before cleaning disconnect the unit from the electricity supply.
•Clean the unit with soft damp cloth
•DO NOT submerge the unit in water or use water sprays to clean it
•Always clean your Chefmaster Crepe Maker daily, this will stop grease
building up and becoming difficult to clean.
•Take care using metal utensils as they can damage the cooking surface
Troubleshooting
Fault
Possible Cause
Solution
The plates are not heating
when the power and
heating indicator are both
on
Temperature controller
may be broken
At least one of heating
wires may have burnt
out
Contact your Chefmaster
distributor
Contact your Chefmaster
distributor
When the power is on and
temperature controller is
switched and heating
indicator is on and
temperature cannot be
controlled
The thermostat may
need to be replaced
Contact your Chefmaster
distributor
Indicator is not on when
the power is on and the
unit is heating
Power indicator light
may need to be replaced
Contact your Chefmaster
distributor
The power is switched on
but the unit is not heating
The fuse may need to be
replaced
Change the fuse
Transportation and Storage
Please handle your Crepe Maker with care to prevent any damage to the unit
and internal parts. The Crepe Maker should be stored somewhere which is
ventilation and non-corrosive gas.
Do not store any flammable objects near the equipment.
Technical Information
HEF572 –Crepe Maker
Voltage 220-240v 50/60Hz
Power 3.0kW
Weight 23 kg
Dimensions 450 x 510 x 240 mm

4
•Chefmaster Crepe Maker are supplied with a 3 pin plug and lead with a
13 amp fuse
•Appliance must be earthed
•If in doubt contact a qualified electrician or your Chefmaster distributor
Disposal
Under WEEE regulations this product must not be disposed of as household
waste. To prevent damage to the environment and humans this product must
be disposed of in an approved and environmentally friendly recycling process.
For more information on how to dispose of this correctly please contact your
Chefmaster distributor or local authority responsible for waste disposal.
Compliance
All Chefmaster parts and products have under gone a stringent testing process
to ensure that comply with all European standards and specifications.
All Chefmaster products carry the CE approval symbol.