Chicco KeyFit 30 Zip User manual

WARNING: Avoid serious injury or death to your child. Never use
your KeyFit car seat without seat padding in place. You must read and
understand the KeyFit 30 Zip Features andSoftgoods Removal instructions
AND the instructions in the User Guide. Keep these instructions. Fold
instructions and store with the booklet in the KeyFit Base. If you do not
understand these instructions, DO NOT attempt to remove theSoftgoods,
STOP and call Chicco at 1-877-424-4226.
INSTRUCTIONS:KeyFit® 30 Zip Features and Softgoods Removal
IMPORTANT: Please also refer to the instructions that came with your product.
Turn Carrier over (upside down).
12 Remove Right and Left Harness Straps from the
Splitter plate.
13
4 1
SS0018E_01
Turn Carrier back over and pull the
Harness Straps from the Carrier.
14 Remove both Shoulder Pads from Harness
Straps. Refer to Adjusting Harness Height in the User
Guide to ensure proper reassembly of Harness Straps.
15
CAUTION
These instructions are in addition to the instructions in the User Guide. Only the differences in the canopy,
seat pad, and boot are outlined. To avoid serious injury or death to your child, you must read and
understand these instructions and the User Guide.
OPENING BOOT:
EXTENDING CANOPY:
SHOULDER PAD REMOVAL:
To extend the Canopy unzip the zipper located at
the back of the Canopy (as shown).
1Once unzipped,pull the Canopy forward.
This will extend the mesh section of the Canopy
and shield more of the child in the KeyFit.
2
Once the Boot is secured, you can still access the
baby through the front zippered flap.
3
WARNING: Avoid serious injury or death to your child. You must make sure that all harness components have
been replaced correctly, so the seat can provide maximum crash protection. Pull on adjuster strap and the shoulder straps of the
harness and operate the harness after this replacement is complete. Make sure all straps are properly routed and secured. Make
sure Chest Clip, and BuckleTongues are oriented and installed correctly. If you have a problem, retry these instructions provided
AND review your User Guide. If you still have problems, STOP, Do Not use the Car Seat, and call Chicco at 1-877-424-4226.

Pull Seat Pad away from the Adjuster Cover as
shown.
Hint: To help remove the Seat Pad, pinch the fabric
above the Adjuster Cover and pull forward.
9Pull the side of the Seat Pad up and slide the
Harness Strap behind the Seat Pad at the shoulder and
the waist, repeat for the other Harness Strap.
10
Make sure the Harness Straps are completely tucked
behind the back of the Seat Pad and remove the Seat Pad.
Make sure back piece of the Seat Pad is properly
tucked into the softgoods when re-attaching the
Seat Pad.
11
BOOT: To remove, undo the snap button
located on the side of Boot. Repeat for other side.
4Remove the boot. Guide the section from under
the front edge of the seat and lift up and remove the
boot.
5
2 3
Unhook the elastic band attached around handle
pivot, repeat for the other side.
8a Pull out plastic tabs located on both sides of the
seat pad.
8b
SOFTGOODS REMOVAL:
PARTS LIST:
A. Newborn Positioner
B. Headrest Insert
C. Shoulder Pads
D. Crotch Strap Pad
E. Boot
AB
C D E
TO REMOVE THE SEAT PAD:
Completely loosen the harness straps. Remove the Boot (See Steps 4-5). Remove the Crotch Strap Pad
(See Step 6). Refer to User Guide to remove the Canopy, Headrest Insert and Newborn Positioner (See Step 7).
Remove the Seat Pad (See Steps 8-11).
CROTCH STRAP PAD: Unbuckle the Harness
and remove Crotch Strap Pad by locating the Tab and
pushing it through the Harness Buckle. Pull the Tab out
through the front of the Harness Buckle and remove.
6
IMPORTANT! If the Crotch Strap Pad prevents the harness from properly
fitting a small Infant, remove immediately and store for future use.
Refer to user guide to remove the
Canopy, Headrest Insert and Newborn
Positioner.
7
Fabrics may be spot-cleaned with mild soap and
water, or machine washed in cold water on delicate
cycle using mild detergent. Hang to dry. DO NOT
BLEACH.
Please consult your product manual for instructions
on additional care and maintenance instructions.
CLEANING
INSTRUCTIONS:
To reinstall softgoods, follow steps 4-11 in reverse.
IMPORTANT! Make sure all softgoods are properly
installed before use.
12