Childcare Montana DL User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
Montana DL
Change Centre “Origami Bunny”
Model # 057626-331

2
This product has been manufactured for a child with a maximum age of 12 months or a maximum weight
of 11kgs.
DO NOT place more than 1kgs of goods in the mesh bag.
Be aware of the risk of open res and other sources of heat,such as electric bar res,gas res,etc.in the near
vicinity of the changing unit.
Use original accessories and manufacturer approved parts only.
DO NOT use this change pad if any part is torn,broken or missing.
ENSURE that the change centre is completely assembled and check that all parts are securely tightened
before use.
Regularly check all parts for tightness - tighten or replace if required.
Promptly replace worn or broken parts.
Read all instructions before assembly and use of the change centre.
Keep instructions for future use.
FOLLOWTHE MANUFACTURER’S INSTRUCTIONS.
DO NOT LEAVEYOUR CHILD UNATTENDED.
CHILDREN HAVE DROWNED WHILE USING BATH AIDS.
THIS IS NOT A SAFETY DEVICE.
ALWAYS KEEPYOUR BABY WITHIN ARM’S REACH.
NEVER LEAVEYOUR BABY INTHE CARE OF CHILDREN.
ALL BRAKES ON CASTORS / WHEELS MUST BE APPLIED BEFORE PLACING YOUR CHILD
ONTHE CHANGE PAD OR IN THE BATH.
DO NOT ALLOW OLDER CHILDRENTO CLIMB OR PLAY ONTHE CHANGE CENTRE.
SAFETY PRECAUTIONS
WARNING

3
Due to variations in the style and design of our products, the photographs and illustrations shown in this
instruction manual are generic,therefore product fabrics,colour and design may vary from images shown.
CNP Brands reserves the right to alter product specications without notice as a result of our ongoing
policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Montana DL Change Centre
Congratulations on your purchase of the Montana DL
Change Centre “Origami Bunny”.
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to read
this manual carefully before using this product and keep it in a
safe place for future reference.
CONGRATULATIONS

4
ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
End panel
Storage
containers
Front tray with
towel rail (L+R)
Mesh bag
x 2
x 3
x 1
x 1
x 1
x 1
x 1
x 1
Rear frame
without plastic
brackets
Front frame with
plastic brackets
Change pad
Bathtub

5
Supplied loose in box continued:
Plastic assembly
tool
Bath frame
support legs with
oor protectors
Support tubes
Bath plug
x 1
x 2
x 2
x 1
x 1
x 12
x 4
x 1
Drain tube
Assembly bolt
44mm bolt for
front frame bath
support
Pre assembled
change pad
frame
Castors x 4
x 1Bottom shelf
ASSEMBLY CONTENTS

6
ASSEMBLY / OPERATING INSTRUCTIONS
To attach pre-assembled Change Pad Frame...
To attach Front and Rear Frames...
1
1
2
3
Attach all four castors by pushing onto bottom of end
panels.
Insert front frame with plastic clips as per image
shown.
Insert two assembly bolts.
Secure using plastic assembly tool.
Repeat for opposite end.
Insert pre-assembled change pad frame into one side
of an end panel.
Insert two assembly bolts and secure using plastic
assembly tool.
Repeat for other end.
1a.
1a.
1b.
1c.
1d.
2a.
3a.
3b.
PLEASE NOTE: You may need the help of another adult for assembly.
PLEASE NOTE: Do not tighten completely.
PLEASE NOTE: Do not tighten completely.

7
ASSEMBLY / OPERATING INSTRUCTIONS
2Insert rear frame into both end panels.
Using the same method as used for front frame
assembly.
2a.
2b.
To assemble Bath Support Frame...
1
2
3
Insert bath frame support leg onto bath frame tube.
Ensure pop pins lock into hole.
Secure top support tubes as shown in image using 2 x
44mm bolts either end.
Repeat for bottom support tube using the remaining 2
x 44mm bolts.
Use a Phillips head screwdriver (not supplied) to secure
all 4 bolts.
1a.
2a.
3a.
3b.
3c.
To attach Front and Rear Frames continued...

8
1
1
2
2
Place bottom shelf in position as shown.
Ensure the cut-outs in the shelf align with the plastic
clips on the frame.
Place change pad into position,and clip to one side
of top frame.
Fold up sides and attach end aps around vertical
bars of side panels,using press studs to secure as
shown.
Lower down and clip other side of change pad
to top frame.
Attach drain hose to outlet on bathtub.
1a.
1b.
1a.
2a.
2a.
2b.
ASSEMBLY / OPERATING INSTRUCTIONS
To attach Bottom Shelf...
To attach change pad...

9
ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Plastic Components...
1
2
3
4
Place the three storage containers into position on the
upper rails of the front and rear frames,creating a shelf
in the centre of the unit.
Place the left component of the front tray into position,
then place the right component ensuring it clips into
the left component as shown.
Ensure the front tray rests against the bar on the top
frame.
Place bathtub into position as shown.
Loosen top bolts on one end panel and place elastic
loops of mesh bag around bolts.
Re-tighten bolts.
1a.
2a.
2b.
3a.
4a.
4b.

10
ASSEMBLY / OPERATING INSTRUCTIONS
To access Bath...
1
2
To access bath,slide bath outwards.
When nished,slide bath back inwards, ensuring the
bottom of the slide out frame clips into the plastic clips
as shown.
1a.
2a.