Cisco MX200 G2 User manual

Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 1
Manpower
Two people working together are required to mount
the system.
Room setup
Explore the Cisco Project Workplace website to
find inspiration and guidelines when preparing your
office or meeting room for video conferencing,
http://www.cisco.com/go/projectworkplace
Documentation
Cisco Spark: Visit the Cisco Spark help site to find
more information about Spark registered room
systems, http://help.ciscospark.com
Other services: Visit the Cisco web site to find user
guides and compliance and safety information for
the video system, http://www.cisco.com/go/mx-docs
This installation guide covers MX200 G2 with a wall-mount.
Dimensions
Height: 745 mm / 29.3in.
Width: 995 mm / 39.2in.
Depth: 150 mm / 5.8 in.
Weight total: 26kg / 57lb
Weight monitor: 24 kg / 53lb

Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 2
• Wall bracket
• Monitor bracket
• Bottom adapter
• Screwdriver
C
D
A
B
Monitor
Accessories:
• Microphone(s)
• Cables
• Screws for mounting
the bottom adapter
• Gloves
Touch controller

Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 3
1Mount the monitor bracket
Use gloves when
handling the monitor.
A B C
Fasten the bracket
with the four screws
that you just removed.
Unscrew these four
screws. You will
re-use them when
fastening the bracket.
Lay the monitor gently face
down on a steady, soft surface.
Take care not to subject the camera
for any stress.
1
2

Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 4
2Mount the bottom adapter
Remove the cable
channel lid for now.
You need it in step 4.
2 × M6x16
A C

Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 5
3Connect the cables
For maintenance only
Reset to factory
settings
Audio line output
Always use the provided
power cable.
The wall socket outlet must
be easily accessible after
installation.
Power switch Audio line input
LAN1
Video input2
(e.g. PC)
Video output2
(e.g. 2nd display)
Power
(100-240 VAC,
50/60 Hz)
Touch
controller1
USB, for future use
HDMI
DVI-I
Microphone3
2nd microphone2, 3
C D
1Use the cable that is labeled with
for the Touch controller; use the cable
that is labeled with for the LAN
2Optional
3Always use the provided Cisco
TelePresence Table Microphone 20

Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 6
4Snap on the cable channel lid
Snap on the cable
channel lid for strain relief.

Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 7
5Mount the monitor to the wall Due to the size and mass of this product, it is
important that the wall-mounted system is safely
installed according to these installation instructions.
The wall and mounting hardware must be able to
safely support the product.
The wall-mounted system must be installed by
qualified personnel, in accordance with state and
local building regulations.
26kg / 57lb
(including brackets)
Use gloves when
handling the monitor.
Fix the bracket to the wall
with four screws. Use screws
and anchors suiting your
type of wall (not provided).
Verify that the bracket is level
before securing it to the wall.
1.2 m
(47 in.)
Recommended distance
for regular meeting rooms:
A

Installing Cisco TelePresence MX200 G2 - Wall Mount
78-100249-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 8
EMC Class A declaration
WARNING: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
声明
此为
A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING: This is a class A product. In a domestic environment
this product may cause radio interference in which case the user
may be required to take adequate measures.
• Connect to power and LAN/Ethernet.
• Switch on the system.
The power switch is placed next to
the power connector at the rear side
of the system.
Wait while the unit starts up. Normally
this takes a few minutes. It may
include automatic software upgrade
and restart of the Touch controller.
• Follow the instructions on the Touch controller.
Cisco Spark: To find more information on how to get started with
Spark registered systems, visit http://help.ciscospark.com and look
for Getting Started articles for room systems.
Other services: For further information on set-up and configuration,
download the Getting Started Guide from the Cisco web site,
http://www.cisco.com/go/mx-docs
Never move the camera manually when power is switched on;
always use the camera control function on the Touch controller to
change the camera position.
6Start up the system
Power
switch
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or
its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to
this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the
property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1110R)
Cisco has more than 200 offices worldwide.
Find an overview of the offices on the Cisco web site at
http://www.cisco.com/go/offices