Clarion VRX928RVD User manual

- 1 - VRX928RVD
Published by Service Dept.
Printed in Japan
Clarion Co., Ltd.
5-35-2, Hakusan, Bunkyouku, Tokyo, 112-8608 Japan
Service Dept.- 50 kamitoda,Toda-shi,Saitama,335-8511 Japan Tel: [phone] FAX:[phone]
298-5999-00 Sep.2002 P
Service Manual
Model
Radio/DVD Multimedia Center with
CeNET Control

(QC-6810E)
(Region No.2)
SPECIFICATIONS
FM tuner section
Frequency range: 87.5MHz to 108.0MHz(0.05MHz
steps)
AM tuner section
Frequency range: MW:531kHz to 1602kHz(9kHz
steps)
LW:153kHz to 279kHz(3kHz steps)
DVD player section
System: Digital versatile disc system with
CDDA capable
Usable discs: DVD video disc,Compact disc
Frequency response: 20Hz to 22kHz(48kHz)(+1/-1dB)
Signal to noise ratio: 100dB(1kHz)IHF-A
Dynamic range: 100dB(1kHz)
Distortion: 0.01%
Audio amplifier section
Rated power output: 18W x 4(20Hz to 20kHz,1%,4 ohm)
Maximum power output:
200W(50W x 4 JEITA)
Speaker impedance: 4 ohm(4 to 8 ohm)
Input section
Video input: 1.0V+0.2/-0.2Vp-p
(input impedance 75 ohm)
Audio input: 130mV+60/-60mVrms(High)
600mV+80/-80mVrms(Mid)
840mV+100/-100mVrms(Low)
(input impedance 10k ohm or
greater)
RGB input section
Video: 0.7V+0.2/-0.2Vp-p(input impedance
75 ohm)
Synchronize: 0.3V+0.9/-0.1Vp-p(input impedance
75 ohm)
Video output section
Video output: 1.0V+0.2/-0.2Vp-p(output imped-
ance 75 ohm)
LCD monitor section
Screen size: 7-inch wide type
(152mm Width x 85mm Height)
Display method: Transmission type TN Liquid
Crystal Display
Drive method: TFT(thin-film transistor) active
matrix driving
Pixels: 336,960(1440x234)
General
Power source voltage: 14.4V DC
(10.8 to 15.6V allowable)
Ground: Negative
Current consumption: 4.0A(1W)
Auto antenna rated current:
500mA less
Dimensions(mm): Main unit
178(W)x50(H)x165(D)
Tuner amp unit
178(W)x37.5(H)x209.5(D)
Remote control unit
54(W)x28.8(H)x155(D)
Weight: Main unit 2.3kg
Tuner amp unit 1.1kg
Remote control unit 70g
(including battery)
* Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of Dolby
Laboratories.
* "DTS" is a registered trademarks of Digital Theater
Systems,Inc.
* Specifications and design are subject to change without
notice for further improvement.

- 2 -VRX928RVD
To engineers in charge of repair or
inspection of our products.
Before repair or inspection, make sure to follow the
instructions so that customers and Engineers in
charge of repair or inspection can avoid suffering
any risk or injury.
1. Use specified parts.
The system uses parts with special safety features against
fire and voltage. Use only parts with equivalent character-
istics when replacing them.
The use of unspecified parts shall be regarded as remod-
eling for which we shall not be liable. The onus of product
liability (PL) shall not be our responsibility in cases where
an accident or failure is as a result of unspecified parts
being used.
2. Place the parts and wiring back in their original positions
after replacement or re-wiring.
For proper circuit construction, use of insulation tubes,
bonding, gaps to PWB, etc, is involved. The wiring connec-
tion and routing to the PWB are specially planned using
clamps to keep away from heated and high voltage parts.
Ensure that they are placed back in their original positions
after repair or inspection.
If extended damage is caused due to negligence during
repair, the legal responsibility shall be with the repairing
company.
3. Check for safety after repair.
Check that the screws, parts and wires are put back se-
curely in their original position after repair. Ensure for safety
reasons there is no possibility of secondary ploblems
around the repaired spots.
If extended damage is caused due to negligence of repair,
the legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the
parts for the automobile.
Disconnect the battery terminal after turning the ignition
key off. If wrong wiring connections are made with the bat-
tery connected, a short circuit and/or fire may occur. If ex-
tensive damage is caused due to negligence of repair, the
legal responsibility shall be with the repairing company.
5. Cautions regarding chips.
Do not reuse removed chips even when no abnormality is
observed in their appearance. Always replace them with
new ones. (The chip parts include resistors, capacitors,
NOTES
* Use a CeNET extension cable that is less than 20m in
length.(including the Y-adapter CCA-519)
* We cannot supply PWB with component parts in prin-
ciple. When a circuit on PWB has failure , please repair
it by component parts base. Parts which are not men-
tioned in service manual are not supplied.
* This DVD player ca play the following discs.
DVD video discs,Video CDs,CD text,Audio CDs.
* This DVD video player cannot playback DVD-R,DVD-
RAM,DVD-ROM,CD-ROM,CD-RW,Photo CDs.
* This DVD player plays NTSC discs and PAL discs only
and cannot be used for playback of SECAM discs.
* Some CDs recorded in CD-R or CD-RW mode may not
be usable.
* This slide mechanism is used the special adjustment jig
for repair.
COMPONENTS
QC-6810E-A
Main unit ----------- 1
Remote control unit RCB-161-200 1
Battery(SUM-3) ----------- 2
Universal mounting bracket 300-9035-01 1
DCP case 335-6707-00 1
Antenna jumper 093-1465-02 1
Power supply lead(18P) 854-6401-00 1
Power supply lead(2P) 854-6393-51 1
Extension lead(20P to 20P) 855-0553-10 1
Extension LEAD(RGB) 855-2480-00 1
Outer escutcheon 940-7715-05 1
Parts bag -----------
Electro tap 060-0018-00 1
Machine screw(M4×3) 714-4003-87 4
Machine screw(M5×8) 714-5008-41 4
Sems hex. bolt(M5×8) 716-0496-01 5
Parts bag -----------
Hook plate 330-8216-01 2
Cord clamp 335-0833-01 1
Spacer 345-3653-01 1
Screw 716-0726-01 1
Parts bag -----------
Mounting bracket 300-7362-00 2
Canoe clip 335-2515-00 4
Machine screw(M4×8) 714-4008-80 4
Parts bag -----------
DCP lock spacer 345-5174-00 1
CAUTIONS
This appliance contains a laser system and is classified as
a "CLASS 1 LASER PRODUCT".To use this model
properly,read this owner's manual carefully and keep this
manual for your future reference.In case of any trouble with
this player,please contact your nearest "AUTHORIZED ser-
vice station".To prevent direct exposure to the laser beam,do
not try to open the enclosure.
Use of controls,adjustment or performance of procedures
other than those specified herein,may result in hazardous
radiation exposure.
The COMPACT DISC player and MINI DISC player should
not be adjusted or repaired by anyone except properly quali-
fied service personnel.

- 3 - VRX928RVD
diodes, transistors, etc). The negative pole of tantalum
capacitors is highly susceptible to heat, so use special care
when replacing them and check the operation afterwards.
6. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the
iron tip temperature is around 270 . Take care not to ap-
ply the iron tip repeatedly(more than three times)to the
same patterns. Also take care not to apply the tip with force.
7. Turn the unit OFF during disassembly and parts replace-
ment. Recheck all work before you apply power to the unit.
8. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through
the lens of the optical pickup. When checking that the la-
ser optical diode lights up, keep your eyes more than 30cms
away from the lens. Prolonged viewing of the laser within
30cms may damage your eyesight.
9. Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by
electrostatic charge caused by your clothes and body.
Make sure to avoid electrostatic charges on your clothes
or body, or discharge static electricity before handling the
optical pickup.
9-1. Laser diode
The laser diode terminals are shorted for transporta-
tion in order to prevent electrostatic damage. After
replacement, open the shorted circuit. When remov-
ing the pickup from the mechanism, short the termi-
nals by soldering them to prevent this damage.
9-2. Actuator
The actuator has a powerful magnetic circuit. If a
magnetic material is put close to it. Its characteris-
tics will change. Ensure that no foreign substances
enter through the ventilation slots in the cover.
9-3. Cleaning the lens
Dust on the optical lens affects performance. To
clean the lens, apply a small amount of isopropyl
alcohol to lens paper and wipe the lens gently.
SYSTEM CHECK
* The confirmation of connected equipment must be per-
formed for this unit only when the wiring connection is
complete and power is turned on to the unit first.When
the power is supplied,"PUSH PWR" appear in the
display.Press the FUNC button,the system check starts
inside the unit.When "COMPLETE" and "PUSH PWR"
appear alternately, press once again the FUNC button.
ERROR DISPLAYS
If an error occurs,one of the following displays is displayed.Take the measures described below to eliminate the problem.
DVD
player
CD
changer
MD
changer
Error display
ERROR 2
ERROR 3
ERROR 6
ERROR 2
ERROR 3
ERROR 6
ERROR H
EEROR 2
ERROR 3
ERROR 6
Cause
A DVD is caught inside the DVD deck and is not ejected.
A DVD cannot be played due to scratches,etc.
A DVD is loaded upside-down inside the DVD deck and
does not play.
A CD inside the CD changer is not loaded.
A CD inside the CD changer cannot be played due to
scratches,etc.
A CD inside the CD changer cannot be played because
it is loaded upside-down.
Displayed when the temperature in the MD changer is
too high and playback has been stopped automatically.
An MD inside the MD changer is not loaded.
An MD inside the MD changer cannot be played due to
scratches,etc.
An MD inside the MD changer cannot be played because
it is loaded upside-down.
Displayed when a non-recorded MD is loaded in the MD
changer.
Measure
This is a failure of DVD deck's mechanism.
Replace with a non-scratched,non-warped disc.
Eject the disc then reload it properly.
This is a failure of CD changer's mechanism.
Replace with a non-scratched,non-warped disc.
Eject the disc then reload it properly.
Lower the surrounding temperature and wait for a
while to cool off MD changer.
This is a failure of MD changer's mechanism.
Replace with a non-scratched,non-warped disc.
Eject the disc then reload it properly.
Load a pre-recorded MD in the MD changer.
Note:If an error display other than the ones described above appears, press the reset button.
* When the reset button is pressed,frequencies of TV/radio stations,titles,etc. stored in memory are cleared.
TROUBLESHOOTING
Problem
Nothing happens when
buttons are pressd.
Display is not accurate.
Cause
The microprocessor has malfunction
due to noise,etc.
Measure
Turn off the power,then press the
RELEASE lever and remove the
DCP.Press the Reset button both
of tuner amp unit and main unit for
about 2 seconds with a thin
rod.When the reset button is
pressed,turn off the ACC power.

- 4 -VRX928RVD
NOTES OF ISO CONNECTOR
1. For VW and Audi vehicles,change the position of fuse
installation as shown on the diagram.(Figure 1)
For models 1992 and later For models up to 1991
Figure 1
2. When the car stereo is installed in 1998 and later
Volkswagen models,make sure to cut the car lead wire
connected the A-5 terminal.(a breakdown could occur if
the lead wire is not cut.)After cutting the lead wire,insulate
the front end of the lead wire with insulation tape to pre-
vent the risk of short-circuits.(Figure 2)
Note: Before cutting the lead wire,disconnect the car
battery - (negative)cable.
Figure 2
3. When Main unit is also connected to an external
amplifier,connect REMOTE on the external amplifier to
the previously cut lead wire on the side of the connector
4. When an extension lead is required in the extension cable
type wiring procedure,disconnect the auto antenna
leads(BLU/WHT).Be sure to insulate both the ISO con-
nector side terminal and the main unit side terminal with
insulation tape,respectively.(Figure 3)
Figure 3
BLOCK DIAGRAM
DVD mechanism section
15A
FUSE
YEL
BLU/WHT
RED
Initial setting of extension lead
YEL
RED
RED
YEL
YEL
RED
RED
YEL
YEL
Insulation tape
Insulate the terminal
Never let the terminals make contact
with the metal plate parts of the car.
*
BLU/WHT BLU/WHT
BLU/WHT

- 5 - VRX928RVD
Tuner amp unit section
4.332MHz
FM DX/LO
AM DX/LO
NAVI
SEL3

- 6 -VRX928RVD
Main unit section
SLIDE MECHANISM
SUB LCD PWB
PANEL SWITCH PWB
LCD PWB
INNER SWITCH PWB
H-DVD MECHANISM
MAIN PWB-A
MAIN PWB-B
MAIN PWB-C
8P

- 7 - VRX928RVD
ADJUSTMENTS
Main unit section
DC-DC converter output voltage / PLL output voltage adjust-
ment
Condition:
Function : VISUAL mode
Tuner amp unit : Input NTSC color bar video signal
1. Adjust VR150 so that the voltage of TP152 is
5.35V(+0.02V/-0.02V).
2. Adjust VR101 so that the voltage of TP105 is 1.8V(+0.3V/
-0.3V).
LCD PWB section
Power supply voltage confirmation
1. Make sure the voltage has become the following value
at each test point.
TP708 : 5.3V(+0.5V/-0.5V)
TP709 : 7.5V(+0.5V/-0.5V)
TP710 : 13.0V(+0.5V/-0.5V)
TP707 : -16.0V(+0.5V/-0.5V)
PLL adjustment
1. TP717 connect to GND. Confirm that the TP716 voltage
is 2.65V(+0.1V/-0.1V).
2. Adjust VR707 so that the frequency of TP718 is
15.734kHz(+50Hz/-50Hz).
Screen position adjustment
1. Adjust VR708 so that the pulse width of TP718 is 4.6u
sec(+0.1u sec./-0.1u sec.).
Voltage confirmation of J702 connector
VGH(pin32) : 13.0V(+0.5V/-0.5V)
VCC(pin24) : -11.0V(+0.5V/-0.5V)
VGL(pin18) : -8.4V(+0.5V/-0.5V)
VSH(pin1,pin3) : 5.3V(+0.5V/-0.5V)
VIDEO signal adjustment
(step 1 to 7 :NTSC, step 8 :PAL)
Input the visual signal(10step wave,monochrome,APL=50%,
1.0Vp-p)to the VIDEO input.
1. BRIGHT voltage confirmation
Make sure the voltage of TP701 is 2.00V(+0.1V/-0.1V).
2. GAMMA 0 voltage confirmation
Make sure the voltage of TP705 is 1.95V(+0.1V/-0.1V).
3. GAMMA 2 voltage confirmation
Make sure the voltage of TP706 is 2.15V(+0.1V/-0.1V).
4. RGB-AMP/CONT-G adjustment
Adjust VR705(RGB AMP) so that VBB voltage of TP712
is 4.0V(+0.05V/-0.05V).
Adjust VR701(CONT) so that VBW voltage of TP712 is
3.8V(+0.05V/-0.05V).
5. BRT-R Adjustment
Adjust VR703(BRT-R) so that VBB voltage of TP713 is
4.0V(+0.05V/-0.05V).
6. BRT-B Adjustment
Adjust VR704(BRT-B) so that VBB voltage of TP711 is
4.0V(+0.05V/-0.05V).
7. COM-AMP adjustment
Adjust VR702(COM-AMP) so that the amplitude of TP714
is 8.0V(+0.1V/-0.1V p-p).
8. Burst cleaning adjustment
Input a color bar signal.(PAL)
Adjust L702 so that the wave form of TP711 is in focus.
VCOM DC bias adjustment
1. Adjust VR706(VCOM DC) to obtain the optimum
contrast(CINEMA MODE).
Voltage/frequency confirmation of inverter section
TP901 : 5.0V(+0.5V/-0.5V)
TP902 : 53kHz(+5kHz/-5kHz)
Tuner amp unit section
S-meter adjustment
1. Input the 98.1MHz/30dBu(400Hz 90% + pilot 10%
MOD)signal.
2. To make a test mode,Press the preset button 6 more
than 1 second while holding the MUTE button.
3. Adjust VR501 so that the reading of the display is 24dB+1/
-1dB(LCD display "24****++").
EXPLANATION OF IC
051-6441-00 ES4408 DVD Processor
1.Terminal Description
pin 1: VCC : - : Positive supply voltage.
pin 2: LA 4 : O : Device address output.
pin 3: LA 5 : O : Device address output.
pin 4: LA 6 : O : Device address output.
pin 5: LA 7 : O : Device address output.
pin 6: LA 8 : O : Device address output.
pin 7: LA 9 : O : Device address output.
pin 8: VSS : - : Negative supply voltage.
pin 9: VCC : - : Positive supply voltage.
pin 10: LA 10 : O : Device address output.
pin 11: LA 11 : O : Device address output.
pin 12: LA 12 : O : Device address output.
pin 13: LA 13 : O : Device address output.
pin 14: LA 14 : O : Device address output.
pin 15: LA 15 : O : Device address output.
pin 16: LA 16 : O : Device address output.
pin 17: VSS : - : Negative supply voltage.
pin 18: VCC : - : Positive supply voltage.
pin 19: LA 17 : O : Device address output.
pin 20: LA 18 : O : Device address output.
pin 21: LA 19 : O : Device address output.
pin 22: LA 20 : O : Device address output.
pin 23: LA 21 : O : Device address output.
pin 24: RESET : IN : Reset signal input.
pin 25: TDM DX/RSEL :I/O: TDM transmit data output. ROM select
input.
pin 26: VSS : - : Negative supply voltage.
pin 27: VCC : - : Positive supply voltage.
pin 28: TDM DR : IN : TDM receive data input.
pin 29: TDM CLK :IN : TDM clock pulse input.
pin 30: TDM FS : IN : TDM frame cynch.
pin 31: TDM TSC : O : TDM output enable.
pin 32: TWS/SEL PLL1 :I/O: Audio transmit frame synchronous pulse
output. Select PLL input.
pin 33: TSD0/SEL PLL0:I/O: Audio transmit serial data output. Select
PLL input.
pin 34: VSS : - : Negative supply voltage.
pin 35: VCC : - : Positive supply voltage.
pin 36: TSD1/SEL PLL1:I/O: Audio transmit serial data output. Select
PLL input.
pin 37: TSD 2 : O : Audio transmit serial data output.
pin 38: TSD 3 : O : Audio transmit serial data output.
pin 39: M CLK : O : The clock puse output to the CD IC.
pin 40: TB CK :I/O: Audio transmit bit clock.
pin 41: SPDIF DOBM : O : S/PDIF format output.
pin 42: NU : - : Not in use.

- 8 -VRX928RVD
pin 43: VSS : - : Negative supply voltage.
pin 44: VCC : - : Positive supply voltage.
pin 45: RSD : IN : Audio receive serial data.
pin 46: RWS : IN : Audio receive frame synch.
pin 47: RBCK : IN : Audio receive bit clock.
pin 48: A PLL CAP : IN: Analog PLL capacitor.
pin 49: X IN : IN : Crystal connection.
pin 50: X OUT : O : Crystal connection.
pin 51: VCC : - : Positive supply voltage.
pin 52: VSS : - : Negative supply voltage.
pin 53: DMA 0 : O : DRAM address output.
pin 54: DMA 1 : O : DRAM address output.
pin 55: DMA 2 : O : DRAM address output.
pin 56: DMA 3 : O : DRAM address output.
pin 57: DMA 4 : O : DRAM address output.
pin 58: DMA 5 : O : DRAM address output.
pin 59: VCC : - : Positive supply voltage.
pin 60: VSS : - : Negative supply voltage.
pin 61: DMA 6 : O : DRAM address output.
pin 62: DMA 7 : O : DRAM address output.
pin 63: DMA 8 : O : DRAM address output.
pin 64: DMA 9 : O : DRAM address output.
pin 65: DMA 10 : O : DRAM address output.
pin 66: DMA 11 : O : DRAM address output.
pin 67: VSS : - : Negative supply voltage.
pin 68: VCC : - : Positive supply voltage.
pin 69: DCAS : O : Column address strobe.
pin 70: DOE/DSCK EN :I/O: Output enable out. Clock enable in.
pin 71: DWE : O : DRAM write enable output.
pin 72: DRAS 0 : O : Raw address strobe output.
pin 73: DRAS 1 : O : Raw address strobe output.
pin 74: DRAS 2 : O : Raw address strobe output.
pin 75: VCC : - : Positive supply voltage.
pin 76: VSS : - : Negative supply voltage.
pin 77: DB 0 :I/O: DRAM data input/output.
pin 78: DB 1 :I/O: DRAM data input/output.
pin 79: DB 2 :I/O: DRAM data input/output.
pin 80: DB 3 :I/O: DRAM data input/output.
pin 81: DB 4 :I/O: Test mode LCD driver control DB.
pin 82: DB 5 :I/O: Test mode LCD driver control DB.
pin 83: VCC : - : Positive supply voltage.
pin 84: VSS : - : Negative supply voltage.
pin 85: DB 6 :I/O: Test mode LCD driver control DB.
pin 86: DB 7 :I/O: Test mode LCD driver control DB.
pin 87: DB 8 :I/O: DRAM data input/output.
pin 88: DB 9 :I/O: DRAM data input/output.
pin 89: DB 10 :I/O: DRAM data input/output.
pin 90: DB 11 :I/O: DRAM data input/output.
pin 91: VSS : - : Negative supply voltage.
pin 92: VCC : - : Positive supply voltage.
pin 93: DB 12 :I/O: DRAM data input/output.
pin 94: DB 13 :I/O: DRAM data input/output.
pin 95: DB 14 :I/O: DRAM data input/output.
pin 96: DB 15 :I/O: DRAM data input/output.
pin 97: DCS 1 : O : SDRAM chip select output.
pin 98: VSS : - : Negative supply voltage.
pin 99: VCC : - : Positive supply voltage.
pin100: DCS 0 : O : SDRAM chip select output.
pin101: DQM : O : Data input/output mask.
pin102: DSCK : O : Clock to SDRAM.
pin103: VSS : - : Negative supply voltage.
pin104: VCC : - : Positive supply voltage.
pin105: D Clock : O : BRI,COL,HUE setting signal output for the
LCD.
pin106: YUV 0 : O : 8-bit YUV output.
pin107: YUV 1 : O : 8-bit YUV output.
pin108: YUV 2 : O : 8-bit YUV output.
pin109: YUV 3 : O : 8-bit YUV output.
pin110: YUV 4 : O : 8-bit YUV output.
pin111: VCC : - : Positive supply voltage.
pin112: VSS : - : Negative supply voltage.
pin113: YUV 5 : O : 8-bit YUV output.
pin114: YUV 6 : O : 8-bit YUV output.
pin115: YUV 7 : O : 8-bit YUV output.
pin116: P CLK 2X SCN :I/O: 2x pixel clock.
pin117: P CLK Q SCN :I/O: Pixel clock.
pin118: VSYNCH :I/O: Vertical synch for screen video interface,
programmable for rising or falling edge.
pin119: HSYNCH :I/O: Horizontal synch for screen video inter-
face, programmable for rising or falling
edge.
pin120: VSS : - : Negative supply voltage.
pin121: VCC : - : Positive supply voltage.
pin122: HD 0/DCI 0 :I/O: Host data & DCI data input/output.
pin123: HD 1/DCI 1 :I/O: Host data & DCI data input/output.
pin124: HD 2/DCI 2 :I/O: Host data & DCI data input/output.
pin125: HD 3/DCI 3 :I/O: Host data & DCI data input/output.
pin126: HD 4/DCI 4 :I/O: Host data & DCI data input/output.
pin127: HD 5/DCI 5 :I/O: Host data & DCI data input/output.
pin128: HD 6/DCI 6 :I/O: Host data & DCI data input/output.
pin129: VSS : - : Negative supply voltage.
pin130: VCC : - : Positive supply voltage.
pin131: HD 7/DCI 7 :I/O: Host data & DCI data input/output.
pin132: HD 8/DCI FDS :I/O: Host data input/output & DCI FDS.
pin133: HD 9 :I/O: Host data input/output.
pin134: HD 10 :I/O: Host data input/output.
pin135: HD 11 :I/O: Host data input/output.
pin136: HD 12 :I/O: Host data input/output.
pin137: HD 13 :I/O: Host data input/output.
pin138: VSS : - : Negative supply voltage.
pin139: VCC : - : Positive supply voltage.
pin140: HD 14 :I/O: Host data input/output.
pin141: HD 15 :I/O: Host data input/output.
pin142: HWRQ : O : Host write request.
pin143: HRDQ : O : Host read request.
pin144: HIRQ/DCI ERR :I/O: Host interrupt.
pin145: HRST : O : Host reset.
pin146: HIORDI : I : Host I/O ready.
pin147: VSS : - : Negative supply voltage.
pin148: VCC : - : Positive supply voltage.
pin149: HWR :I/O: Host write signal input / DCI interface
acknowledge signal output.
pin150: HRD : O : Host read signal output / DCI interface
clock output.
pin151: HIOCS16 : IN : Device 16-bit data transfer.
pin152: HCS1FX : O : Host select 1.
pin153: HCS3FX : O : Host select 3.
pin154: HA 0 :I/O: Host address bus.
pin155: HA 1 :I/O: Host address bus.
pin156: VSS : - : Negative supply voltage.
pin157: VCC : - : Positive supply voltage.
pin158: HA 2 :I/O: Host address bus.
pin159: VPP : - : Connect to ground.
pin160: AUX 0 :I/O: Auxiliary input/output.
pin161: AUX 1 :I/O: Auxiliary input/output.
pin162: AUX 2 :I/O: Auxiliary input/output.
pin163: VSS : - : Negative supply voltage.
pin164: VCC : - : Positive supply voltage.
pin165: AUX 3 :I/O: Auxiliary input/output.
pin166: AUX 4 :I/O: Auxiliary input/output.
pin167: AUX 5 :I/O: Auxiliary input/output.
pin168: AUX 6 :I/O: Auxiliary input/output.
pin169: AUX 7 :I/O: Auxiliary input/output.
pin170: LOE : O : Device output enable.
pin171: VSS : - : Negative supply voltage.
pin172: VCC : - : Positive supply voltage.
pin173: LCS 0 : O : Chip select output.
pin174: LCS 1 : O : Chip select output.
pin175: LCS 2 : O : Chip select output.
pin176: LCS 3 : O : Chip select output.
pin177: VSS : - : Negative supply voltage.
pin178: LD 0 :I/O: Device data input/output.
pin179: LD 1 :I/O: Device data input/output.
pin180: LD 2 :I/O: Device data input/output.
pin181: LD 3 :I/O: Device data input/output.
pin182: LD 4 :I/O: Device data input/output.
pin183: VCC : - : Positive supply voltage.
pin184: VSS : - : Negative supply voltage.
pin185: LD 5 :I/O: Device data input/output.
pin186: LD 6 :I/O: Device data input/output.
pin187: LD 7 :I/O: Device data input/output.
pin188: LD 8 :I/O: Device data input/output.
pin189: LD 9 :I/O: Device data input/output.

- 9 - VRX928RVD
pin190: LD 10 :I/O: Device data input/output.
pin191: LD 11 :I/O: Device data input/output.
pin192: VSS : - : Negative supply voltage.
pin193: VCC : - : Positive supply voltage.
pin194: LD 12 :I/O: Device data input/output.
pin195: LD 13 :I/O: Device data input/output.
pin196: LD 14 :I/O: Device data input/output.
pin197: LD 15 :I/O: Device data input/output.
pin198: LWRLL : O : Device write enable.
pin199: LWRHL : O : Device write enable.
pin200: VSS : - : Negative supply voltage.
pin201: VCC : - : Positive supply voltage.
pin202: NU : - : Not in use.
pin203: NU : - : Not in use.
pin204: LA 0 : O : Device address output.
pin205: LA 1 : O : Device address output.
pin206: LA 2 : O : Device address output.
pin207: LA 3 : O : Device address output.
pin208: VSS : - : Negative supply voltage.
052-5041-51 TMP95CW64F-3UR6(Z)DVD Mechanism Control-
ler
1.Terminal Description
pin 1: A Vref : IN : Reference voltage for the internal ADC.
pin 2: A VSS : - : Analog ground.
pin 3: A VCC : - : Positive supply voltage for the internal
analog section.
pin 4: NU : - : Not in use.
pin 5: NU : - : Not in use.
pin 6: Connect 7 :IN : Connect to pin7.
pin 7: EJECT SW :IN : Eject switch signal input.
pin 8: A MUTE : O : The audio mute signal output.
pin 9: SYS P 1 : O : System power 1 control signal output.
pin 10: NU : - : Not in use.
pin 11: RESET : O : Reset signal output.
pin 12: TEST 0 : O : For the test.
pin 13: TEST 1 : O : For the test.
pin 14: TEST 2 : O : For the test.
pin 15: TEST 3 : O : For the test.
pin 16: MCW : O : Loading motor control output.
pin 17: MCCW : O : Loading motor control output.
pin 18: TX D2 : O : The serial data output.
pin 19: RX D2 : IN : The serial data input.
pin 20: DVD R DE CS : O : The chip select signal output to the DVD
ROM decoder.
pin 21: DVD PRO CS : O : The chip enable signal output to DVD
processor.
pin 22: NU : - : Not in use.
pin 23: SPNDL CNT : O : Spindle control output.
pin 24: NU : - : Not in use.
pin 25: VCC : - : Positive supply voltage.
pin 26: GND : - : Ground.
pin 27: X 1 : - : Crystal connection.
pin 28: X 2 : - : Crystal connection.
pin 29: CNNCT VCC : IN : Connect to VCC.
pin 30: RESET : IN : Reset signal input.
pin 31: ACC CNT :IN : ACC ON signal input.
pin 32: NU : - : Not in use.
pin 33: LE TIME : O : For loading/eject time.
pin 34: FG PULSE :IN : FG pulse input.
pin 35: DISC MT SHRT : IN : Disc motor short brake.
pin 36: DATA REQ : O : The data request.
pin 37: D PRO INT :IN: The interrupt signal input from DVD pro-
cessor.
pin 38: CMMD DT REQ : O : The command data request output.
pin 39: REM 5V : O : Power ON signal output to the 5V supply
circuit.
pin 40: ID CONTINUE : O : ID check.
pin 41: DVD R DE INT :IN : The interrupt signal input from the DVD
ROM decoder.
pin 42: NU : - : Not in use.
pin 43: DVD R DE RST: O : The reset signal output to the DVD ROM
decoder.
pin 44: VCC : - : Positive supply voltage.
pin 45: D 0 :I/O: Data input/output.
pin 46: D 1 :I/O: Data input/output.
pin 47: D 2 :I/O: Data input/output.
pin 48: D 3 :I/O: Data input/output.
pin 49: D 4 :I/O: Data input/output.
pin 50: D 5 :I/O: Data input/output.
pin 51: D 6 :I/O: Data input/output.
pin 52: D 7 :I/O: Data input/output.
pin 53: TEST 4 : O : For the test.
pin 54: TEST 5 : O : For the test.
pin 55: TEST 6 : O : For the test.
pin 56: TEST 7 : O : For the test.
pin 57: TEST 8 :I/O: For the test.
pin 58: TEST 9 :I/O: For the test.
pin 59: TEST 10 :I/O: For the test.
pin 60: TEST 11 :I/O: For the test.
pin 61: CNNCT VCC :IN : Connect to VCC.
pin 62: GND : - : Ground.
pin 63: VCC : - : Positive supply voltage.
pin 64: BUSY OUT : O : Busy flag output.
pin 65: DISC : O : Disc distinction signal output.
pin 66: LAYER : O : Layer distinction signal output.
pin 67: NU : - : Not in use.
pin 68: CHUKING : IN : The chucking switch signal input.
pin 69: DVD MCH S 1 : IN : The sensor signal input from DVD mech-
anism.
pin 70: DVD MCH S 2 : IN : The sensor signal input from DVD mech-
anism.
pin 71: DVD MCH S 3 : IN : The sensor signal input from DVD mech-
anism.
pin 72: NU : - : Not in use.
pin 73: NU : - : Not in use.
pin 74: NU : - : Not in use.
pin 75: NU : - : Not in use.
pin 76: MA : O : MA.
pin 77: NU : - : Not in use.
pin 78: NU : - : Not in use.
pin 79: NU : - : Not in use.
pin 80: AD 7 : O : Address output.
pin 81: AD 6 : O : Address output.
pin 82: AD 5 : O : Address output.
pin 83: AD 4 : O : Address output.
pin 84: AD 3 : O : Address output.
pin 85: AD 2 : O : Address output.
pin 86: AD 1 : O : Address output.
pin 87: AD 0 : O : Address output.
pin 88: RD STRB : O : The read strobe output.
pin 89: WR STRB : O : The write strobe output.
pin 90: NU : - : Not in use.
pin 91: GND : - : Ground.
pin 92: TEST 12 : IN: For the test.
pin 93: TEST 13 : IN: For the test.
pin 94: TEST 14 : IN: For the test.
pin 95: TEST 15 : IN: For the test.
pin 96: TEST 16 : IN: For the test.
pin 97: TEST 17 : IN: For the test.
pin 98: LIMIT SNC : IN : The inside limit signal input from the
mechanism.
pin 99: NU : - : Not in use.
pin100: Vref H : - : Reference voltage.
052-6056-10 M30620MCA-F92GP Master System controller
1.Terminal Description
pin 1: SPEED PULSE : IN : The speed pulse input.
pin 2: TIME BASE :IN : Time base pulse input.
pin 3: SPEED SEL 1 : O : The time constant select signal output for
the speed pulse counter.
pin 4: SPEED SEL 2 : O : The time constant select signal output for
the speed pulse counter.
pin 5: RDS CLK : IN : RDS clock pulse input.
pin 6: BYTE : IN : Connect to the ground.
pin 7: CN VSS :IN : Connect to VSS.
pin 8: SYS ACC : O : ACC detect signal output.
pin 9: NU : - : Not in use.
pin 10: RESET : IN : Reset signal input.
pin 11: X OUT : O : Crystal connection.
pin 12: VSS : - : Negative supply voltage.

- 10 -VRX928RVD
pin 13: X IN : IN : Crystal connection.
pin 14: VCC : - : Positive supply voltage.
pin 15: NMI : IN : Connect to VCC.
pin 16: ACC DET : IN: ACC detection signal input.
pin 17: BU DET :IN : Backup detection signal input.
pin 18: MST REQ : IN: The master request signal input.
pin 19: 27pin connect : IN : Connect to 27pin.
pin 20: AMP REM DT : IN: Remote controller wire short detection.
pin 21: EX AMP REM : O : The external amplifier control signal out-
put.
pin 22: NU : - : Not in use.
pin 23: SLAVE ON : O : Slave ON signal output.
pin 24: BUS IN/OUT : O : The audio signal control for Ce-NET.
pin 25: NU : - : Not in use.
pin 26: IR OUT : O : The remote-control signal input for the
navigation.
pin 27: IE BUS RX : IN : IE Bus serial data input.
pin 28: IE BUS TX : O : IE Bus serial data output.
pin 29: NU : - : Not in use.
pin 30: NU : - : Not in use.
pin 31: NU : - : Not in use.
pin 32: PLL CE : O : The chip enable signal output to the PLL
IC.
pin 33: PLL DO : O : Serial data output to the PLL IC.
pin 34: PLL DI : IN : Serial data input from the PLL IC.
pin 35: PLL SCLK : O : The clock pulse output for PLL.
pin 36: NU : - : Not in use.
pin 37: NU : - : Not in use.
pin 38: NU : - : Not in use.
pin 39: NU : - : Not in use.
pin 40: NU : - : Not in use.
pin 41: FLASH WR : IN : The writing flag input for the flash mem-
ory.
pin 42: VOL CLK : O : The clock pulse output to the volume IC.
pin 43: VOL DO : O : Serial data output to the volume IC.
pin 44: AREA 1 : IN : The destination setting input.
pin 45: AREA 2 : IN : The destination setting input.
pin 46: NU : - : Not in use.
pin 47: NU : - : Not in use.
pin 48: VIDE1/2ASEL : O : The audio signal select pulse output.
pin 49: SEL 2 : IN : The selection signal input.
pin 50: SEL 3 : IN : The selection signal input.
pin 51: V2 SEL 2 : IN: The selection signal input.
pin 52: V2 SEL 3 : IN: The selection signal input.
pin 53: FRNT IMAG 1 : O : The front image signal select pulse out-
put.
pin 54: FRNT IMAG 2 : O : The front image signal select pulse out-
put.
pin 55: FRNT IMAG 3 : O : The front image signal select pulse out-
put.
pin 56: REAR IMAG 1 : O : The rear image signal select pulse output.
pin 57: REAR IMAG 2 : O : The rear image signal select pulse output.
pin 58: REAR IMAG 3 : O : The rear image signal select pulse output.
pin 59: REAR IMAG 4 : O : The rear image signal select pulse output.
pin 60: VCC : - : Positive supply voltage.
pin 61: NU : - : Not in use.
pin 62: VSS : - : Negative supply voltage.
pin 63: NU : - : Not in use.
pin 64: REAR IMAG 5 : O : The rear image signal select pulse output.
pin 65: FM ST/SD : IN : At receiving the FM station, this port de-
tects the stereo signal. And at seeking or
scanning, this port detects the station
detection signal.
pin 66: NOISE DISCH : O : The noise discharge command output for
RDS.
pin 67: MUTE SPD UP : O : Station detection speed up command out-
put for RDS.
pin 68: RDS TEST : O : The diagnosis terminal.
pin 69: RDS MUTE : O : RDS mute signal output.
pin 70: RDS DATA : IN : RDS serial data input.
pin 71: NU : - : Not in use.
pin 72: SYS MUTE : O : System muting signal output.
pin 73: 5V ON : O : The ON command output to the power
supply section.
pin 74: AV ON : O : The ON command output to the power
supply section.
pin 75: DVD 8V : O : The ON signal output to the 8V power
supply section for DVD.
pin 76: A ANT REM : O : The automatic antenna control signal out-
put.
pin 77: LINE MUTE : O : The line mute signal output.
pin 78: NU : - : Not in use.
pin 79: AMP MUTE : O : Muting signal output to the Audio Power
Amplifier.
pin 80: AMP REM : O : The control signal output to internal au-
dio power amplifier.
pin 81: PHONE INT : IN : The telephone interrupt signal input.
pin 82: ILL DET :IN : Illumination ON signal input.
pin 83: PKB : IN: The parking brake signal input.
pin 84: NU : - : Not in use.
pin 85: NU : - : Not in use.
pin 86: NU : - : Not in use.
pin 87: NU : - : Not in use.
pin 88: NU : - : Not in use.
pin 89: S METER : IN : The input terminal of internal A/D convert-
er to monitor the radio field strength.
pin 90: NOISE : IN : The noise level for RDS.
pin 91: SPAN DATA : IN : The serial data input from the spectrum
analyzer.
pin 92: NU : - : Not in use.
pin 93: NU : - : Not in use.
pin 94: A VSS : - : Analog ground.
pin 95: NU : - : Not in use.
pin 96: A Vref : IN : Reference voltage for the internal ADC.
pin 97: A VCC : - : Positive supply voltage for the internal
analog section.
pin 98: SPAN A : O : Spectrum analyzer band selection.
pin 99: SPAN B : O : Spectrum analyzer band selection.
pin100: SPAN C : O : Spectrum analyzer band selection.
052-6058-00 MR27V802D-37TPZA00 8M bit One Time PROM
1.Terminal Description
pin 1: NU : - : Not in use.
pin 2: A 18 : IN : The address input.
pin 3: A 17 : IN : The address input.
pin 4: A 7 : IN : The address input.
pin 5: A 6 : IN : The address input.
pin 6: A 5 : IN : The address input.
pin 7: A 4 : IN : The address input.
pin 8: A 3 : IN : The address input.
pin 9: A 2 : IN : The address input.
pin 10: A 1 : IN : The address input.
pin 11: A 0 : IN : The address input.
pin 12: Chip enable : IN : Chip enable signal input.
pin 13: VSS : - : Ground.
pin 14: Output enable : IN : Output enable signal input.
pin 15: D 0 : O : The data output.
pin 16: D 8 : O : The data output.
pin 17: D 1 : O : The data output.
pin 18: D 9 : O : The data output.
pin 19: D 2 : O : The data output.
pin 20: D 10 : O : The data output.
pin 21: D 3 : O : The data output.
pin 22: D 11 : O : The data output.
pin 23: VCC : - : Positive supply voltage.
pin 24: D 4 : O : The data output.
pin 25: D 12 : O : The data output.
pin 26: D 5 : O : The data output.
pin 27: D 13 : O : The data output.
pin 28: D 6 : O : The data output.
pin 29: D 14 : O : The data output.
pin 30: D 7 : O : The data output.
pin 31: D 15 / A -1 :I/O: The data output. / The address input.
pin 32: VSS : - : Ground.
pin 33: BYTE : IN : 8bit/16bit selection.
pin 34: A 16 : IN : The address input.
pin 35: A 15 : IN : The address input.
pin 36: A 14 : IN : The address input.
pin 37: A 13 : IN : The address input.
pin 38: A 12 : IN : The address input.
pin 39: A 11 : IN : The address input.
pin 40: A 10 : IN : The address input.
pin 41: A 9 : IN : The address input.
pin 42: A 8 : IN : The address input.
pin 43: NU : - : Not in use.
pin 44: NU : - : Not in use.

- 11 - VRX928RVD
052-7055-20 NZX0100-1801L Touch-panel & Sub-LCD Con-
troller
1.Terminal Description
pin 1: C 1 : - : Not in use.
pin 2: VL 1 : IN : Positive voltage input for the LCD.
pin 3: LCD ON : O : LCD back light ON signal output.
pin 4: GREEN 1 : O : The LED drive output.
pin 5: AMBER 1 : O : The LED drive output.
pin 6: AUT DIMM : IN : The automatic dimmer signal input.
pin 7: Y R IN : IN : The input terminal of the internal ADC.
pin 8: X R IN : IN : The input terminal of the internal ADC.
pin 9: Y G IN : IN : The input terminal of the internal ADC.
pin 10: X G IN : IN : The input terminal of the internal ADC.
pin 11: KS OUT 2 : O : Key scan output.
pin 12: KS OUT 1 : O : Key scan output.
pin 13: KS OUT 0 : O : Key scan output.
pin 14: DIMMER : O : PWM output.
pin 15: KS IN 3 : IN : Key scan input.
pin 16: KS IN 2 : IN : Key scan input.
pin 17: KS IN 1 : IN : Key scan input.
pin 18: KS IN 0 : IN : Key scan input.
pin 19: GREEN 2 : O : The LED drive output.
pin 20: AMBER 2 : O : The LED drive output.
pin 21: TXD : O : The serial data output.
pin 22: RXD : IN : The serial data input.
pin 23: ST0 :IN : Connect to the ground.
pin 24: TPW : IN : The touch panel control input.
pin 25: PA :I/O: The touch panel control input/output.
pin 26: CHK : O : The touch panel control output.
pin 27: Y- : O : The touch panel control output.
pin 28: X- : O : The touch panel control output.
pin 29: Y+ : O : The touch panel control output.
pin 30: X+ : O : The touch panel control output.
pin 31: REQ O : O : Transmit request signal output.
pin 32: BUSY : IN : The busy flag input.
pin 33: KS OUT 3 : O : Key scan output.
pin 34: NU : - : Not in use.
pin 35: RESET : IN : Reset signal input.
pin 36: BLUE OUT : O : The LED drive output.
pin 37: P 7 : O : FL ON
pin 38: X IN : IN : Crystal connection.
pin 39: X OUT : O : Crystal connection.
pin 40: VSS : - : Negative supply voltage.
pin 41: P 5 : O : VIDEO / RGB
pin 42: P 1 : O : MODE S
pin 43: DATA : O : DATA
pin 44: LOAD : O : LOAD
pin 45: CLOCK : O : The clock pulse output.
pin 46: P 4 : O : CLAMP
pin 47: P 6 : O : VIDEO / MUTE
pin 48: P 0 : O : NTSC / PAL
pin 49: P 3 : O : MODE N
pin 50: P 2 : O : MODE W
pin 51: SEG 39 : O : The segment output.
pin 52: SEG 38 : O : The segment output.
pin 53: SEG 37 : O : The segment output.
pin 54: SEG 36 : O : The segment output.
pin 55: SEG 35 : O : The segment output.
pin 56: SEG 34 : O : The segment output.
pin 57: SEG 33 : O : The segment output.
pin 58: SEG 32 : O : The segment output.
pin 59: SEG 31 : O : The segment output.
pin 60: SEG 30 : O : The segment output.
pin 61: SEG 29 : O : The segment output.
pin 62: SEG 28 : O : The segment output.
pin 63: SEG 27 : O : The segment output.
pin 64: SEG 26 : O : The segment output.
pin 65: SEG 25 : O : The segment output.
pin 66: SEG 24 : O : The segment output.
pin 67: SEG 23 : O : The segment output.
pin 68: SEG 22 : O : The segment output.
pin 69: SEG 21 : O : The segment output.
pin 70: SEG 20 : O : The segment output.
pin 71: SEG 19 : O : The segment output.
pin 72: SEG 18 : O : The segment output.
pin 73: SEG 17 : O : The segment output.
pin 74: SEG 16 : O : The segment output.
pin 75: SEG 15 : O : The segment output.
pin 76: SEG 14 : O : The segment output.
pin 77: SEG 13 : O : The segment output.
pin 78: SEG 12 : O : The segment output.
pin 79: SEG 11 : O : The segment output.
pin 80: SEG 10 : O : The segment output.
pin 81: SEG 9 : O : The segment output.
pin 82: SEG 8 : O : The segment output.
pin 83: SEG 7 : O : The segment output.
pin 84: SEG 6 : O : The segment output.
pin 85: SEG 5 : O : The segment output.
pin 86: SEG 4 : O : The segment output.
pin 87: SEG 3 : O : The segment output.
pin 88: SEG 2 : O : The segment output.
pin 89: SEG 1 : O : The segment output.
pin 90: SEG 0 : O : The segment output.
pin 91: VCC : - : Positive supply voltage.
pin 92: Vref : - : Reference voltage.
pin 93: A Vss : - : Analog ground.
pin 94: COMMON 3 : O : The common signal output.
pin 95: COMMON 2 : O : The common signal output.
pin 96: COMMON 1 : O : The common signal output.
pin 97: COMMON 0 : O : The common signal output.
pin 98: VL 3 : IN: Positive supply voltage for LCD.
pin 99: VL 2 : IN: Positive supply voltage for LCD.
pin100: C 2 : - : Not in use.
052-7062-10 uPD703037AGF-A11-3BA Main Display Control
1.Terminal Description
pin 1: NU : - : Not in use.
pin 2: ESS CK : IN: The clock pulse input from DVD Signal
Processor.
pin 3: ESS RST : O : The reset pulse output to DVD Signal
Processor.
pin 4: DVD ACC ON : O : DVD ACC ON.
pin 5: DVD EJECT : O : DVD EJECT.
pin 6: TP RX : IN : The serial data input from the touch pan-
el.
pin 7: TP TX : O : The serial data output to the touch pan-
el.
pin 8: TP REQ :IN : The request signal from the touch panel.
pin 9: VDD : - : Positive supply voltage.
pin 10: VSS : - : Negative supply voltage.
pin 11: TP RST : O : The reset pulse output to the touch pan-
el.
pin 12: BEEP : O : Beep out.
pin 13: DVD 8V DET :IN : DVD 8V detection.
pin 14: KS IN 0 : IN : Key scan input.
pin 15: KS IN 1 : IN : Key scan input.
pin 16: IRI : IN : The remote control signal input.
pin 17: KS IN 2 : IN : Key scan input.
pin 18: KS IN 3 : IN : Key scan input.
pin 19: KS OUT 0 : O : Key scan output.
pin 20: KS OUT 1 : O : Key scan output.
pin 21: FLASH PRG : IN: The flash memory program command in-
put.
pin 22: KS OUT 2 : O : Key scan output.
pin 23: GREEN : O : Signal output for the LED.
pin 24: AMBER : O : Signal output for the LED.
pin 25: BLINK LED : O : Signal output for the LED.
pin 26: IE RX : IN : IE-Bus serial data intput.
pin 27: IE TX : O : IE-Bus serial data output.
pin 28: EEP DI : IN : The serial data input from EEP-ROM.
pin 29: EEP DO : O : The serial data output to EEP-ROM.
pin 30: EEP CLK : O : The clock pulse output to EEP-ROM.
pin 31: EEP CEO : O : The chip enable signal output to EEP-
ROM.
pin 32: V SEL : O : The video select output.
pin 33: FLASH WR : IN: The write flag input from the flash ROM.
pin 34: RESET : IN : Reset signal input.
pin 35: PLL DOWN : IN : Not in use.
pin 36: NU : - : Not in use.

- 12 -VRX928RVD
pin 37: REG CAPA : - : The capacitor connection.
pin 38: X OUT : O : Crystal connection.
pin 39: X IN : IN : Crystal connection.
pin 40: GND : - : Ground.
pin 41: VDD : - : Positive supply voltage.
pin 42: NU : - : Not in use.
pin 43: NAVI ON : O : NAVI ON signal output.
pin 44: BLK : O : The blanking signal output.
pin 45: RGB ON : O : RGB ON signal output.
pin 46: UP/DWN MF : O : Up/Down motor control.
pin 47: UP/DWN MR : O : Up/Down motor control.
pin 48: OPN CLS MF : O : Open/Close motor control.
pin 49: OPN CLS MR : O : Open/Close motor control.
pin 50: OSD CD 7 :I/O: The parallel data input/output for the on
screen display.
pin 51: OSD CD 6 :I/O: The parallel data input/output for the on
screen display.
pin 52: OSD CD 5 :I/O: The parallel data input/output for the on
screen display.
pin 53: OSD CD 4 :I/O: The parallel data input/output for the on
screen display.
pin 54: OSD CD 3 :I/O: The parallel data input/output for the on
screen display.
pin 55: OSD CD 2 :I/O: The parallel data input/output for the on
screen display.
pin 56: OSD CD 1 :I/O: The parallel data input/output for the on
screen display.
pin 57: OSD CD 0 :I/O: The parallel data input/output for the on
screen display.
pin 58: VDD : - : Positive supply voltage.
pin 59: GND : - : Ground.
pin 60: OSD RD : O : The read command output for the on
screen display.
pin 61: OSD WR : O : The write command output for the on
screen display.
pin 62: OSD CS : O : The chip select signal output to on screen
display.
pin 63: OSD PS2 : O : On screen display port select.
pin 64: OSD PS1 : O : On screen display port select.
pin 65: OSD PS0 : O : On screen display port select.
pin 66: OSD RST : O : The reset pulse output for the on screen
display.
pin 67: ROM EN : O : ROM enable signal output.
pin 68: PNL ON : O : The panel ON signal output.
pin 69: MTR PWR SEL : O : The voltage select signal output for the
motors.
pin 70: MTR ON : O : The motor ON signal output.
pin 71: DVD ON 2 : O : DVD ON signal output.
pin 72: DVD ON 1 : O : DVD ON signal output.
pin 73: AV ON : O : The ON command output to the power
supply section.
pin 74: A VDD : - : Positive supply voltage for the Analog
section.
pin 75: A VSS : - : Analog ground.
pin 76: A Vref : IN : Reference voltage for the internal ADC.
pin 77: OSD WAIT : IN : The wait signal input for the on screen
display.
pin 78: INIT 1 : IN : The initial setting input.
pin 79: INIT 2 : IN : The initial setting input.
pin 80: INIT 3 : IN : The initial setting input.
pin 81: INIT 4 : IN : The initial setting input.
pin 82: INIT 5 : IN : The initial setting input.
pin 83: SYS PWR 1 :IN: System power ON signal input.
pin 84: PWR SW :IN: Power switch signal input.
pin 85: EJECT SW : IN: Eject switch signal input.
pin 86: OPEN SW : IN : Open switch signal input.
pin 87: TILT AD : IN : The input terminal of the internal ADC to
sense the tilt.
pin 88: OPEN AD : IN : The input terminal of the internal ADC to
detect the mechanism state.
pin 89: BU DET :IN : Backup detection signal input.
pin 90: SLAVE ON : IN : Slave ON signal input.
pin 91: DCP DET : IN: DCP detection siganl input.
pin 92: SW INT : IN : The switch signal input.
pin 93: ILL DET : IN: Illumination ON signal input.
pin 94: OSD INT : IN : The interrupt signal input for the on
screen display.
pin 95: MST REQ : O : The master request signal output.
pin 96: ESS RESET : IN : The reset signal input from DVD Signal
Processor.
pin 97: F END RST : O : The front end reset.
pin 98: ESS DO : O : The serial data output to DVD Signal Pro-
cessor.
pin 99: ESS CK : O : The clock pulse output to DVD Signal
Processor.
pin100: ESS DI : IN : The serial data input from DVD Signal
Processor.
052-7063-10 MR27V1602F-OHDTP 16M bit One Time PROM
1.Terminal Description
pin 1: NU : - : Not in use.
pin 2: A 18 : IN : The address input.
pin 3: A 17 : IN : The address input.
pin 4: A 7 : IN : The address input.
pin 5: A 6 : IN : The address input.
pin 6: A 5 : IN : The address input.
pin 7: A 4 : IN : The address input.
pin 8: A 3 : IN : The address input.
pin 9: A 2 : IN : The address input.
pin 10: A 1 : IN : The address input.
pin 11: A 0 : IN : The address input.
pin 12: Chip enable : IN : Chip enable signal input.
pin 13: VSS : - : Ground.
pin 14: Output enable : IN : Output enable signal input.
pin 15: D 0 : O : The data output.
pin 16: D 8 : O : The data output.
pin 17: D 1 : O : The data output.
pin 18: D 9 : O : The data output.
pin 19: D 2 : O : The data output.
pin 20: D 10 : O : The data output.
pin 21: D 3 : O : The data output.
pin 22: D 11 : O : The data output.
pin 23: VCC : - : Positive supply voltage.
pin 24: D 4 : O : The data output.
pin 25: D 12 : O : The data output.
pin 26: D 5 : O : The data output.
pin 27: D 13 : O : The data output.
pin 28: D 6 : O : The data output.
pin 29: D 14 : O : The data output.
pin 30: D 7 : O : The data output.
pin 31: D 15 / A -1 :I/O: The data output. / The address input.
pin 32: VSS : - : Ground.
pin 33: BYTE : IN : 8bit/16bit selection.
pin 34: A 16 : IN : The address input.
pin 35: A 15 : IN : The address input.
pin 36: A 14 : IN : The address input.
pin 37: A 13 : IN : The address input.
pin 38: A 12 : IN : The address input.
pin 39: A 11 : IN : The address input.
pin 40: A 10 : IN : The address input.
pin 41: A 9 : IN : The address input.
pin 42: A 8 : IN : The address input.
pin 43: A 19 : IN : The address input.
pin 44: NU : - : Not in use.

- 13 - VRX928RVD
EXPLODED VIEW : PARTS LIST
Main unit 1/2 section
1 370-9613-00 ESCUTCHEON 1
2 345-5186-00 SLIDER 2
3 382-6463-00 BUTTON EJECT 1
4 347-6795-00 SPACER 1
5 335-6729-00 BUTTON PLATE 1
6 039-2137-00 INNER SWITCH PWB 1
(WITHOUT COMPONENT)
7 346-0151-00 LEATHER SHEET 1
8 335-6730-00 DICS GUIDE 1
9 335-6728-00 RELEASE LEVER 1
10 750-6729-00 SPRING 1
11 331-3391-00 DCP HOLDER 1
1
2
2
3
4
56
7
8
9
10
11
12
13
14
15
15
15
16
17
18
19
19
20
21
22
23
24
25
26
27
28
29
29
29
29
30
31
32
33
34
35
36
37
38
39
40
41
41
41
41
42
44
45
46
28
28
47
48
49
49
50
51
52 53
56
55
54
54
55
57
58 59
60
61
62
63
43
20
65
64
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY
12 331-3392-00 DCP PLATE 1
13 750-6728-00 SPRING RELEASE 1
14 743-1500-20 E-RING 1
15 716-0872-02 PAD SCREW 10
16 335-6836-00 IR PLATE 1
17 DCP-419-300 DCP ASSY 1
18 746-0931-00 WASHER 1
19 746-0761-00 WASHER 2
20 781-2650-00 SCREW 2
21 331-3389-01 BRACKET A 1
22 331-3390-00 BRACKET B 1

- 14 -VRX928RVD
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY
23 313-1841-00 HEAT SINK 1
24 816-2584-00 FLAT WIRE(45P) 1
25 816-2585-00 FLAT WIRE(50P) 1
26 854-4547-50 EXTENSION LEAD 1
27 714-2610-81 MACHINE SCREW 2
28 039-2225-00 MAIN PWB 1
(WITHOUT COMPONENT)
29 716-0878-00 IT-SCREW 5
30 929-2125-01 DVD MECHANISM MODULE 1
31 311-1853-00 LOWER CASE 1
32 331-3387-00 MECHANISM BRKT 1
33 331-3388-00 EARTH PLATE 1
34 286-6104-00 SETPLATE 1
35 816-2582-00 FLAT WIRE(18P) 1
36 816-2583-00 FLAT WIRE(18P) 1
37 039-2147-00 FLEXIBLE PWB(DVD 50P) 1
38 855-0552-01 MULTI POLE CORD 1
39 020-3045-00 FAN(DC-MOTOR) 1
40 780-2014-00 SCREW 2
41 714-2603-81 MACHINE SCREW 4
42 347-6794-00 SHIELD FILM 1
43 714-2604-81 MACHINE SCREW 2
44 345-5175-00 SPACER 1
45 345-5176-00 SPACER 1
46 290-8183-00 DTS LABEL 1
47 060-4008-00 IR-RECEIVER 1
48 013-7411-50 DETECTOR SWITCH 1
49 013-6507-50 LUMI SWITCH 3
50 013-6519-50 LUMI SWITCH 12
51 074-1287-70 OUTLET SOCKET(20P) 1
52 074-1125-02 OUTLET SOCKET(2P) 1
53 075-0385-00 JACK(OPTICAL) 1
54 074-1189-95 OUTLET SOCKET(45P) 2
55 074-1189-00 OUTLET SOCKET(50P) 2
56 074-1205-00 OUTLET SOCKET(50P) 2
57 074-1287-70 OUTLET SOCKET(20P) 1
58 076-0576-15 PLUG(15P) 1
59 076-0276-05 PLUG(5P) 1
60 060-0100-01 BUZZER 1
61 347-6796-00 PROTECT FILM 1
62 076-0488-02 PLUG(2P) 1
63 074-1100-68 OUTLET SOCKET(18P) 1
64 714-3004-81 MACHINE SCREW(M3x4) 1
65 074-1231-08 OUTLET SOCKET(RGB8P) 1
Main unit 2/2 section
1 039-2138-00 LCD PWB 1
(WITHOUT COMPONENT)
2 039-2140-00 SUB LCD PWB 1
(WITHOUT COMPONENT)
3 347-6783-00 REFLECTOR 1
4 335-6734-00 ILLUMI PLATE 1
5 347-6782-00 FILM 1
6 379-1237-41 INDICATOR(SUB LCD) 1
7 347-6805-00 SHADE 1
8 331-3408-00 S-LCD HOLDER 1
9 345-8739-01 SPACER 2
10 335-6731-00 S-LCD COVER 1
11 382-6465-00 BUTTON(DISP/OPN) 1
12 382-6464-00 BUTTON(+/-) 1
13 373-0983-02 DIAL COVER 1
14 378-0537-00 BADGE 1
15 716-3483-00 SCREW 2
16 716-1845-01 SCREW 2
17 781-2040-01 P-SCREW 4
18 370-9614-02 ESCUTCHEON 1
19 371-5729-01 TRIM PLATE 1
20 335-6732-00 REFLECTOR 1
21 382-6466-03 BUTTON(A/N/TILT) 1
22 382-6467-02 BUTTON(6-PIECES) 1
23 382-6468-02 BUTTON(FF/REW) 1
24 039-2139-01 PANEL SWITCH PWB 1
(WITHOUT COMPONENT)
25 716-0872-00 PAD SCREW 3
26 347-6834-00 SHADE 1
27 335-6491-01 ES-COVER(L) 1
28 335-6492-01 ES-COVER(R) 1
29 714-5008-41 MACHINE SCREW 2
30 750-3137-02 SPRING(L) 1
31 750-3137-03 SPRING(R) 1
32 714-2604-81 MACHINE SCREW 6
33 379-0458-10 INDICATOR(7INCH LCD) 1
34 013-9706-00 SWITCH ASSY 1
35 347-6450-00 DOUBLE FACE 1
36 347-6629-00 DOUBLE FACE 1
37 347-6085-00 DOUBLE FACE 4
38 345-8598-00 CUSHION 1
39 345-8618-01 CUSHION 2
40 347-6805-00 SHADE 1
41 383-0687-00 BADGE(CLARION) 1
42 345-8737-00 SHADE 2
43 716-1845-01 SCREW 3
44 347-6780-00 SHADE 1
45 948-0646-01 SLIDE MECHANISM ASSY 1
46 347-6586-00 MOTOR COVER 2
47 347-6451-00 DOUBLE FACE 4
48 347-6781-00 INSULATOR(LCD) 1
49 335-6733-02 UPPER TRIM 1
50 039-2144-01 FLEXIBLE PWB(50P) 1
51 781-2026-00 SCREW 5
52 781-1750-00 SCREW 4
53 738-2630-17 PRECISION SCREW 2
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY

- 15 - VRX928RVD
54 781-1722-00 SCREW 6
55 780-2003-00 SCREW 1
56 335-6776-00 SENSOR ILLUMI 1
57 345-5185-01 GASKET 1
58 345-8738-00 SPACER 2
59 347-6807-00 SPACER 2
60 347-5541-01 INSULATOR 1
61 076-0529-04 PLUG(4P) 1
62 074-1189-95 OUTLET SOCKET(45P) 1
63 074-1189-85 OUTLET SOCKET(35P) 1
64 074-1205-82 OUTLET SOCKET(32P) 1
65 074-1275-58 OUTLET SOCKET(8P) 1
66 076-0645-80 PLUG(30P) 1
67 074-1276-80 OUTLET SOCKET(30P) 1
68 074-1296-64 OUTLET SOCKET(14P) 1
69 076-0663-64 PLUG(14P) 1
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY
1
2
3
4
5
6
7
8
9
10
11
9
12
13
14
15
15
16
16
17
17
17
18
19
20
21
22 23
24
25
26
27
28
29
29
30
31
32
32
32
33
34
35
36
37
37
38
39
39
40
41
42
42
43
43
45
46
47
47
48
44
49
50
51
51
51
51
51
52
53
53
54
54
54
55
56
57
58
58
59
60
61 62
63 64 65
66
25 67
68 69

- 16 -VRX928RVD
How to release the LCD module
1. Remove the screws(No.Ax2) and the springs(No.Bx2).
2. Remove the screws(No.Cx2,Dx4,Ex2) and release the
flexible PWB(No.F).
3. Release the lower case with DVD
mechanism(No.G).Release the cover(No.Hx2).
4. Remove the screws(No.Ix6,Jx2,Kx4,Lx3) and release the
escutchen(No.M).
5. Pull out the LCD module(with switch ass'y) and release
32P/8P/4P connectors.
C
C
D
DE
50PIN SOCKE
T
50PIN FLEXIBLE PWB
F
F
H
H
I
I
JK
A
B
A
B
L
L
M
G
Tuner amp unit section
1 039-2117-02 TUNER PWB 1
(WITHOUT COMPONENT)
2 331-3407-00 FRONT PLATE 1
3 331-3405-00 OUTLET HOLDER 1
4 331-3406-00 IC HOLDER 1
5 313-1730-00 HEAT SINK 1
6 702-3008-81 TAP SCREW 3
7 714-3006-81 MACHINE SCREW 3
8 714-2612-81 MACHINE SCREW 3
9 311-1741-03 LOWER CASE 1
10 310-1649-06 UPPER CASE 1
11 716-0878-00 IT-SCREW 4
12 714-2605-81 MACHINE SCREW 4
13 013-5102-00 SLIDE SWITCH 1
14 074-1030-00 OUTLET SOCKET 2
15 092-0612-03 ANTENNA RECEPTACLE 1
16 880-2089M TUNER 1
17 074-1125-18 OUTLET SOCKET 1
18 074-1194-00 OUTLET SOCKET(13P) 1
19 074-1134-00 OUTLET SOCKET(20P) 1
20 075-0310-03 JACK 1
21 013-3949-00 SWITCH 1
22 075-9002-02 JACK(4P) 1
23 051-2038-10 IC(LA47501) 1
24 075-9001-00 JACK(6P) 1
25 073-0762-90 TERMINAL 1
NO. PART NO. DESCRIPTION Q'TY
12
12
11
11
11
11
10
9
1
6
2
5
4
8
3
7
6
23
22
21
20
19
18
17
16
15
14
13
24
25

- 17 - VRX928RVD
DVD mechanism section
1
1-1
13
12
10
11
8
2
9
9
9
3
3
3
3
7
7
7
7
6
6
6
6
5
4
1 HBS-523-100 MECHANISM ASSY 1
1-1 SMA-187-100 LOADING MOTOR ASSY 1
2 039-1946-01 MAIN PWB 1
(WITHOUT COMPONENT)
3 750-3450-01 DAMPER SPRING 4
4 620-0993-00 FRONT STOPPER 1
5 620-0994-01 CHASSIS 1
6 629-0078-02 DAMPER 4
7 716-1851-00 SCREW(M2×2) 4
8 716-1856-00 SCREW(M2×2) 1
9 716-1864-00 SCREW(M1.7×4.5) 3
10 074-1189-00 OUTLET SOCKET(50P) 1
11 074-1201-68 OUTLET SOCKET(18P) 2
12 074-1059-80 OUTLET SOCKET(30P) 1
13 013-7412-50 DETECTOR SWITCH 1
HOW TO CHECK
When the mechanism assy HBS-523-100 is replaced,please
check the operation by the following procedure.
Preparation
1. Test disc
DVD : TDV-562(made by ALMEDIO)
CD : TCD-732RA(made by ALMEDIO)
Procedure
Operation check by test DVD(TDV-562)
1. Insert the test DVD and play chapter 16. Then,check the
access operation.
2. Play chapter 1. Then ,check the access operation.
3. If there is no problem,the operation must be OK.
Operation check by test CD(TCD-732RA)
1. Insert the test CD and play track 15. Then,check the jump-
ing sound.
2. Play track 1. Then,check the jumping sound.
3. If there is no problem,the operation must be OK.
Checking standard
DVD play:Can be played without any stopping and
distortion.(more than 10 sec.)
CD play:Can be played correctly without jumping
sound.(more than 10 sec.)
Access operation:The access time from inner to outer and
outer to inner must be within 2.5 seconds.
NO. PART NO. DESCRIPTION Q'TY
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
Note) Several different parts of the same reference number are alternative parts.
One of those parts is used in the set.
ELECTRICAL PARTS LIST
Tuner PWB(B1) section
BL501 880-2089M TUNER
C502 166-2201-50 22pF CH
C503 166-1007-50 10pF CH
C506 042-0643-51 16V100uF
C507 168-1032-55 0.01uF
C508 168-2232-55 0.022uF
C510 168-2232-55 0.022uF
C512 042-0643-51 16V100uF
C513 168-1032-55 0.01uF
C514 168-6822-55 6800pF
C516 168-8222-55 8200pF
C517 166-1501-50 15pF CH
C518 166-1801-50 18pF CH
C519 042-0643-51 16V100uF
C520 168-1222-55 1200pF
C521 168-1832-55 0.018uF
C522 168-1832-55 0.018uF
C523 168-1022-55 1000pF
C524 043-0277-51 0.022uF
C525 168-1022-55 1000pF
C526 163-1053-65 50V1uF
C527 168-1042-78 16V 0.1uF
C528 166-1011-50 100pF CH
C529 042-0474-92 50V1uF NP
C530 178-1052-78 1uF
C531 178-1052-78 1uF
C532 178-1052-78 1uF
C533 178-1052-78 1uF
C534 163-1063-35 16V10uF
C535 166-1011-50 100pF CH
C537 168-3312-55 330pF
C538 168-2232-55 0.022uF
C539 168-1032-55 0.01uF
C540 163-4763-15 6.3V47uF
C544 163-4753-55 35V4.7uF
C545 178-1052-78 1uF

- 18 -VRX928RVD
C546 178-1052-78 1uF
C547 178-1052-78 1uF
C548 168-1032-55 0.01uF
C549 168-1042-78 16V 0.1uF
C550 163-1063-35 16V10uF
C551 168-3312-55 330pF
C552 168-1042-78 16V 0.1uF
C553 168-5612-55 560pF
C554 168-2232-55 0.022uF
C555 166-2201-50 22pF CH
C556 178-1052-78 1uF
C557 178-1052-78 1uF
C558 163-1063-35 16V10uF
C559 178-1052-78 1uF
C560 163-2263-15 6.3V22uF
C561 168-8212-55 820pF
C562 168-1042-78 16V 0.1uF
C563 168-6812-55 680pF
C564 168-1042-78 16V 0.1uF
C565 166-2201-50 22pF CH
C566 168-1032-55 0.01uF
C567 168-1032-55 0.01uF
C568 163-4763-15 6.3V47uF
C569 168-1042-78 16V 0.1uF
C570 168-2232-55 0.022uF
C571 184-1083-12 6.3V1000uF
C572 163-4763-15 6.3V47uF
C573 168-1032-55 0.01uF
C574 166-3096-50 3pF CJ
C575 163-4763-15 6.3V47uF
C576 168-1042-78 16V 0.1uF
C577 163-1073-35 16V100uF
C578 184-1083-12 6.3V1000uF
C579 168-1022-55 1000pF
C581 168-1022-55 1000pF
C601 163-1063-35 16V10uF
C602 168-1042-78 16V 0.1uF
C603 166-1011-50 100pF CH
C604 042-0416-57 10V47uF
C605 043-0506-50 0.1uF
C606 168-1042-78 16V 0.1uF
C607 043-0506-50 0.1uF
C608 166-1011-50 100pF CH
C609 042-0559-00 5.5V0.1uF
C610 168-1042-78 16V 0.1uF
C613 168-1042-78 16V 0.1uF
C614 042-0595-84 10V100uF
C615 163-4763-35 16V47uF
C616 168-1022-55 1000pF
C617 168-1032-55 0.01uF
C618 168-1042-78 16V 0.1uF
C619 168-1042-78 16V 0.1uF
C620 168-2245-79 0.22uF
C621 168-1042-78 16V 0.1uF
C622 168-1042-78 16V 0.1uF
C623 168-1032-55 0.01uF
C624 168-1042-78 16V 0.1uF
C625 163-1063-35 16V10uF
C626 163-1063-35 16V10uF
C627 168-1022-55 1000pF
C628 168-4722-55 4700pF
C629 168-1042-78 16V 0.1uF
C630 168-4732-78 0.047uF
C633 163-4753-55 35V4.7uF
C634 168-4732-78 0.047uF
C635 168-1032-55 0.01uF
C1001 168-1042-78 16V 0.1uF
C1002 163-1053-65 50V1uF
C1003 163-1063-35 16V10uF
C1004 163-1053-65 50V1uF
C1005 042-0592-58 16V10uF
C1006 042-0592-58 16V10uF
C1007 042-0592-58 16V10uF
C1008 042-0592-58 16V10uF
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
C1009 168-1042-78 16V 0.1uF
C1010 042-0592-58 16V10uF
C1011 042-0592-58 16V10uF
C1012 042-0592-58 16V10uF
C1013 042-0592-58 16V10uF
C1014 042-0592-58 16V10uF
C1015 042-0592-58 16V10uF
C1016 166-3301-50 33pF CH
C1017 166-3301-50 33pF CH
C1018 163-4763-35 16V47uF
C1019 042-0416-57 10V47uF
C1020 168-1042-78 16V 0.1uF
C1021 166-1511-50 150pF CH
C1022 166-3301-50 33pF CH
C1023 166-3301-50 33pF CH
C1024 166-1511-50 150pF CH
C1025 163-1063-35 16V10uF
C1026 168-1042-78 16V 0.1uF
C1027 166-1011-50 100pF CH
C1028 166-1011-50 100pF CH
C1029 042-0474-92 50V1uF NP
C1030 042-0474-92 50V1uF NP
C1031 042-0474-90 16V10uF
C1032 042-0474-90 16V10uF
C1033 178-3342-78 0.33uF
C1034 166-1011-50 100pF CH
C1035 166-1011-50 100pF CH
C1036 043-0506-50 0.1uF
C1037 163-1063-35 16V10uF
C1038 168-1042-78 16V 0.1uF
C1039 163-1063-35 16V10uF
C1040 168-1042-78 16V 0.1uF
C1041 163-4763-15 6.3V47uF
C1042 163-2263-35 16V22uF
C1043 168-1042-78 16V 0.1uF
C1044 163-1063-35 16V10uF
C1045 042-0592-58 16V10uF
C1046 042-0592-58 16V10uF
C1047 168-1042-78 16V 0.1uF
C1048 168-1042-78 16V 0.1uF
C1049 042-0474-90 16V10uF
C1050 042-0474-90 16V10uF
C1051 163-1063-35 16V10uF
C1052 168-1042-78 16V 0.1uF
C1053 042-0595-84 10V100uF
C1054 168-1042-78 16V 0.1uF
C1055 163-1063-35 16V10uF
C1056 168-1042-78 16V 0.1uF
C1057 042-0595-84 10V100uF
C1058 163-2263-35 16V22uF
C1059 168-4732-78 0.047uF
C1060 168-1042-78 16V 0.1uF
C1061 042-0592-58 16V10uF
C1062 042-0592-58 16V10uF
C1063 042-0592-58 16V10uF
C1064 042-0592-58 16V10uF
C1065 042-0592-58 16V10uF
C1066 042-0592-58 16V10uF
C1067 168-1042-78 16V 0.1uF
C1068 168-1042-78 16V 0.1uF
C1069 042-0592-58 16V10uF
C1070 168-1042-78 16V 0.1uF
C1071 042-0592-58 16V10uF
C1072 042-0592-58 16V10uF
C1073 042-0592-58 16V10uF
C1074 168-1042-78 16V 0.1uF
C1075 163-1063-35 16V10uF
C1076 163-1063-35 16V10uF
C1077 163-1063-35 16V10uF
C1078 163-2273-25 10V 220uF
C1080 163-2273-25 10V 220uF
C1081 042-0592-74 50V 2.2uF
C1082 042-0592-61 16V47uF
C1083 042-0592-74 50V 2.2uF
C1084 042-0592-58 16V10uF
C1085 042-0592-61 16V47uF
C1086 042-0592-58 16V10uF
C1087 042-0592-58 16V10uF
C1088 042-0592-61 16V47uF
C1089 042-0592-58 16V10uF
C1092 166-1011-50 100pF CH
C1094 168-1042-78 16V 0.1uF
C1095 166-1011-50 100pF CH
C1096 042-0595-84 10V100uF
C1097 042-0595-84 10V100uF
C1098 042-0595-84 10V100uF
C1099 042-0595-84 10V100uF
C1100 042-0595-84 10V100uF
C1101 042-0595-84 10V100uF
C1102 042-0592-50 6.3V22uF
C1103 042-0592-50 6.3V22uF
C1104 042-0592-50 6.3V22uF
C1105 042-0592-50 6.3V22uF
C1106 042-0592-50 6.3V22uF
C1107 042-0592-50 6.3V22uF
C1108 168-1522-55 1500pF
C1109 168-1522-55 1500pF
C1110 168-1522-55 1500pF
C1111 168-1522-55 1500pF
C1112 168-1522-55 1500pF
C1113 168-1522-55 1500pF
C1114 163-1063-35 16V10uF
C1115 163-1053-65 50V1uF
C1118 043-0506-50 0.1uF
C1119 163-1063-35 16V10uF
C1120 163-1063-35 16V10uF
C1121 168-4732-78 0.047uF
C1122 168-4732-78 0.047uF
C1123 043-0506-50 0.1uF
C1124 043-0506-52 0.47uF
C1125 043-0506-52 0.47uF
C1126 043-0506-52 0.47uF
C1127 043-0506-52 0.47uF
C1128 163-4763-35 16V47uF
C1133 163-2263-35 16V22uF
C1134 043-0506-50 0.1uF
C1135 043-0506-50 0.1uF
C1136 163-3353-65 50V3.3uF
C1137 042-0592-58 16V10uF
C1138 042-0592-58 16V10uF
C1139 042-0592-58 16V10uF
C1140 042-0592-58 16V10uF
C1141 042-0592-58 16V10uF
C1142 042-0592-58 16V10uF
C1143 042-0592-58 16V10uF
C1144 042-0592-58 16V10uF
C1145 163-1063-35 16V10uF
C1146 163-1053-65 50V1uF
C1147 168-1032-55 0.01uF
C1148 166-8201-50 82pF CH
C1149 163-1063-35 16V10μF
C1150 168-1042-78 16V 0.1uF
C1151 184-4783-32 16V4700uF
C1152 172-2231-11 0.022uF
C1153 184-2283-32 16V2200uF
C1154 172-1041-11 0.1uF
C1155 168-1042-78 16V 0.1uF
C1156 168-1042-78 16V 0.1uF
C1157 168-1042-78 16V 0.1uF
C1158 168-1042-78 16V 0.1uF
C1160 163-1063-35 16V10uF
C1161 163-1063-35 16V10uF
C1162 163-1063-35 16V10uF
C1163 163-1063-35 16V10uF
C1164 166-1511-50 150pF CH
C1165 166-1511-50 150pF CH
C1166 168-1522-55 1500pF
C1167 168-1522-55 1500pF

- 19 - VRX928RVD
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
C1168 168-1522-55 1500pF
C1169 168-1522-55 1500pF
C1170 168-1522-55 1500pF
C1171 168-1522-55 1500pF
C1172 166-4701-50 47pF CH
C1173 166-4701-50 47pF CH
C1174 166-4701-50 47pF CH
C1175 166-4701-50 47pF CH
C1176 166-4701-50 47pF CH
C1177 166-4701-50 47pF CH
C1178 043-0506-50 0.1uF
C1179 166-1511-50 150pF CH
C1180 166-1511-50 150pF CH
C1181 166-1511-50 150pF CH
C1182 166-1511-50 150pF CH
C1183 166-1511-50 150pF CH
C1184 166-1511-50 150pF CH
C1185 166-1511-50 150pF CH
C1186 166-1511-50 150pF CH
CCT601 050-0122-53 1/16W 1k ohmx4J
CCT602 050-0122-53 1/16W 1k ohmx4J
CCT603 050-0122-53 1/16W 1k ohmx4J
CCT604 050-0122-53 1/16W 1k ohmx4J
CCT605 050-0122-53 1/16W 1k ohmx4J
CCT606 050-0122-53 1/16W 1k ohmx4J
CCT608 050-0122-53 1/16W 1k ohmx4J
D501 001-0367-91 1SS226
D502 001-0367-91 1SS226
D503 001-0367-91 1SS226
D504 001-0367-91 1SS226
D505 001-0367-91 1SS226
D506 001-0367-91 1SS226
D507 001-0516-90 MA111
D508 001-0516-90 MA111
D509 001-0367-91 1SS226
D601 001-0516-90 MA111
D602 001-0516-90 MA111
D604 001-0516-90 MA111
D605 001-0516-90 MA111
D606 001-0516-90 MA111
D607 001-2403-90 M1F60
D608 001-0516-90 MA111
D609 001-0503-46 HZS9B2L
D610 001-0516-90 MA111
D611 001-0516-90 MA111
D612 001-0516-90 MA111
D613 001-0516-90 MA111
D614 001-0516-90 MA111
D615 001-0516-90 MA111
D617 001-0516-90 MA111
D618 001-0516-90 MA111
D619 001-0516-90 MA111
D1001 001-0537-90 SFPM-62
D1002 001-0537-90 SFPM-62
D1003 001-0537-90 SFPM-62
D1004 001-0516-90 MA111
D1005 001-0516-90 MA111
D1006 001-0516-90 MA111
D1007 001-0516-90 MA111
D1008 001-0529-44 MA8082-M
D1009 001-0503-46 HZS9B2L
D1011 001-2403-90 M1F60
D1012 001-0516-90 MA111
D1013 001-2403-90 M1F60
D1014 001-2403-90 M1F60
D1015 001-2403-90 M1F60
D1016 001-2403-90 M1F60
D1018 001-2403-90 M1F60
D1019 001-2403-90 M1F60
D1020 001-2403-90 M1F60
D1021 001-2403-90 M1F60
D1022 001-0592-00 RM4Z
D1023 001-0516-90 MA111
D1024 001-0516-90 MA111
D1025 001-0516-90 MA111
D1026 001-0516-90 MA111
D1027 001-0529-69 MA8180-M
D1028 001-0529-69 MA8180-M
D1029 001-0529-69 MA8180-M
D1030 001-0529-69 MA8180-M
F1001 060-8023-58 3A
F1002 060-8023-58 3A
F1003 060-8023-58 3A
IC501 051-6201-90 LC72146M
IC502 051-5306-90 MM1117XF
IC503 051-5306-90 MM1117XF
IC504 051-5306-90 MM1117XF
IC505 051-5823-90 LC72723M
IC506 051-0350-93 NJM4558M
IC507 051-5306-90 MM1117XF
IC508 051-5331-90 MM1228XFBE
IC509 051-5326-90 TK15420MTL
IC601 051-6600-38 CA0008AM
IC602 052-6056-10 M30620MCA-F92GP
IC603 051-5408-08 S-80921ANMP-DDJ
IC604 051-5818-90 BA3834F
IC605 051-0869-58 NJM2103M
IC606 051-1215-08 TC74HC132AF
IC1001 051-1811-90 BA3129F
IC1002 051-1905-93 AN77L06M
IC1003 051-0350-93 NJM4558M
IC1004 051-3015-90 NJM4580M
IC1005 051-5020-90 M61508FP
IC1006 051-0350-93 NJM4558M
IC1007 051-7232-08 74VHC4066M
IC1008 051-5810-90 TDA8574T
IC1009 051-5810-90 TDA8574T
IC1010 051-5810-90 TDA8574T
IC1012 051-3015-90 NJM4580M
IC1015 051-2038-10 LA47501
IC1016 051-3015-90 NJM4580M
IC1017 051-3015-90 NJM4580M
J501 074-1030-00 MINI-DIN-8P
J502 074-1030-00 MINI-DIN-8P
J503 075-0310-03 JACK
J504 075-9002-02 JACK
J1001 074-1125-18 18P
J1002 074-1134-00 20P
J1003 075-9001-00 6P
J1004 074-1194-00 13P CE-NET
L501 010-2003-04 COIL
L502 010-2199-90 220uH J
L503 010-2199-90 220uH J
L505 010-2285-58 BLM21A102FPB
L506 010-2285-58 BLM21A102FPB
L507 010-2199-71 5.6uH J
L601 010-2199-78 22uH J
L602 010-2285-51 BLM21A05PT
L603 010-2285-51 BLM21A05PT
L604 010-2285-51 BLM21A05PT
L1001 010-2199-78 22uH J
L1002 010-2199-78 22uH J
L1003 010-3052-78 220uH
L1004 010-3052-78 220uH
L1005 010-8024-00 CHOKE
L1006 010-8033-00 180uH
Q501 108-0669-00 2SK669
Q502 125-2004-93 RN1403
Q503 193-1306-00 2SD1306
Q504 125-0002-93 RN2403
Q505 190-1162-50 2SA1162Y.G
Q506 190-1298-00 2SA1298
Q507 125-2004-92 RN1402
Q601 125-0021-97 DTA113ZU
Q602 125-0021-97 DTA113ZU
Q603 192-2712-50 2SC2712Y.G.L
Q604 125-0021-97 DTA113ZU
Q605 190-1162-50 2SA1162Y.G
Q607 192-2712-50 2SC2712Y.G.L
Q608 190-1162-50 2SA1162Y.G
Q609 190-1162-50 2SA1162Y.G
Q610 103-1270-16 2SD1270P
Q611 108-0241-28 2SK241GR
Q612 190-1162-50 2SA1162Y.G
Q613 125-2004-93 RN1403
Q614 125-2004-93 RN1403
Q615 190-1162-50 2SA1162Y.G
Q616 125-2004-93 RN1403
Q619 190-1162-50 2SA1162Y.G
Q620 125-0002-96 RN2406
Q621 108-0241-28 2SK241GR
Q622 125-0021-91 DTA114EU
Q623 192-2712-50 2SC2712Y.G.L
Q1001 190-1298-00 2SA1298
Q1002 125-2004-92 RN1402
Q1003 101-1143-00 2SB1143
Q1004 125-2004-93 RN1403
Q1005 125-0002-96 RN2406
Q1006 125-2004-96 RN1406
Q1007 192-2712-50 2SC2712Y.G.L
Q1008 102-3420-50 2SC3420GR,BL
Q1009 108-0241-50 2SK241Y,GR
Q1010 125-2004-93 RN1403
Q1011 190-1162-50 2SA1162Y.G
Q1012 125-2004-93 RN1403
Q1015 190-1736-00 2SA1736
Q1016 125-2004-93 RN1403
Q1017 192-2712-50 2SC2712Y.G.L
Q1018 190-1162-50 2SA1162Y.G
Q1019 125-4001-90 XN1504
Q1020 125-4001-90 XN1504
Q1021 125-4001-90 XN1504
Q1024 190-1313-00 2SA1313O,Y
Q1025 192-2712-50 2SC2712Y.G.L
Q1026 125-4001-90 XN1504
Q1027 125-4001-90 XN1504
Q1028 125-4001-90 XN1504
Q1029 125-4001-90 XN1504
R501 119-4721-15 1/16W 4.7k ohm
R503 116-3311-15 1/8W 330 ohm
R504 119-2221-15 1/16W 2.2k ohm
R505 119-1231-15 1/16W 12k ohm
R507 119-2711-15 1/16W 270 ohm
R508 119-7501-15 1/16W 75 ohm
R509 119-7501-15 1/16W 75 ohm
R510 119-2221-15 1/16W 2.2k ohm
R511 119-7501-15 1/16W 75 ohm
R512 119-1021-15 1/16W 1k ohm
R513 119-7501-15 1/16W 75 ohm
R514 032-0140-12 1/10W 75 ohm
R515 119-1021-15 1/16W 1k ohm
R517 119-1021-15 1/16W 1k ohm
R518 119-1021-15 1/16W 1k ohm
R519 119-8211-15 1/16W 820 ohm
R520 119-5621-15 1/16W 5.6k ohm
R521 119-1031-15 1/16W 10k ohm
R522 119-1031-15 1/16W 10k ohm
R523 119-5631-15 1/16W 56k ohm
R524 119-5631-15 1/16W 56k ohm
R526 119-1041-15 1/16W 100k ohm
R527 119-3311-15 1/16W 330 ohm
R528 119-1031-15 1/16W 10k ohm
R529 119-1521-15 1/16W 1.5k ohm
R530 119-1021-15 1/16W 1k ohm
R531 119-1031-15 1/16W 10k ohm
R532 119-1031-15 1/16W 10k ohm
R533 119-1521-15 1/16W 1.5k ohm
R534 119-1031-15 1/16W 10k ohm
R535 119-1231-15 1/16W 12k ohm
R536 119-3321-15 1/16W 3.3k ohm
R537 119-3331-15 1/16W 33k ohm
R538 032-0140-12 1/10W 75 ohm

- 20 -VRX928RVD
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
R539 119-4731-15 1/16W 47k ohm
R540 119-1041-15 1/16W 100k ohm
R541 119-2211-15 1/16W 220 ohm
R542 119-2221-15 1/16W 2.2k ohm
R543 119-2221-15 1/16W 2.2k ohm
R544 119-1011-15 1/16W 100 ohm
R545 119-4721-15 1/16W 4.7k ohm
R546 119-1031-15 1/16W 10k ohm
R547 119-1031-15 1/16W 10k ohm
R548 119-3901-15 1/16W 39 ohm
R549 119-7501-15 1/16W 75 ohm
R550 119-4731-15 1/16W 47k ohm
R551 119-1021-15 1/16W 1k ohm
R552 119-1021-15 1/16W 1k ohm
R553 119-2211-15 1/16W 220 ohm
R601 119-3321-15 1/16W 3.3k ohm
R602 119-4731-15 1/16W 47k ohm
R603 119-4731-15 1/16W 47k ohm
R604 119-4731-15 1/16W 47k ohm
R607 119-4731-15 1/16W 47k ohm
R608 119-4731-15 1/16W 47k ohm
R609 119-1021-15 1/16W 1k ohm
R610 119-1021-15 1/16W 1k ohm
R611 116-6801-15 1/8W 68 ohm
R613 119-1021-15 1/16W 1k ohm
R614 119-4721-15 1/16W 4.7k ohm
R615 119-4721-15 1/16W 4.7k ohm
R616 119-1031-15 1/16W 10k ohm
R617 119-1031-15 1/16W 10k ohm
R618 119-1031-15 1/16W 10k ohm
R619 119-1031-15 1/16W 10k ohm
R620 119-4731-15 1/16W 47k ohm
R621 119-4731-15 1/16W 47k ohm
R622 119-4731-15 1/16W 47k ohm
R623 119-4731-15 1/16W 47k ohm
R624 119-1021-15 1/16W 1k ohm
R625 116-1011-15 1/8W 100 ohm
R627 119-1021-15 1/16W 1k ohm
R628 119-1021-15 1/16W 1k ohm
R629 119-1031-15 1/16W 10k ohm
R630 119-2231-15 1/16W 22k ohm
R631 119-4731-15 1/16W 47k ohm
R632 119-4731-15 1/16W 47k ohm
R633 119-4731-15 1/16W 47k ohm
R634 119-1521-15 1/16W 1.5k ohm
R635 119-3311-15 1/16W 330 ohm
R636 119-1031-15 1/16W 10k ohm
R637 119-1041-15 1/16W 100k ohm
R638 119-1031-15 1/16W 10k ohm
R642 119-1031-15 1/16W 10k ohm
R643 119-1031-15 1/16W 10k ohm
R644 119-2221-15 1/16W 2.2k ohm
R645 119-1031-15 1/16W 10k ohm
R646 119-4731-15 1/16W 47k ohm
R647 119-1031-15 1/16W 10k ohm
R648 119-1541-15 1/16W 150k ohm
R649 119-1031-15 1/16W 10k ohm
R650 119-4731-15 1/16W 47k ohm
R651 119-1041-15 1/16W 100k ohm
R652 119-3331-15 1/16W 33k ohm
R653 119-4321-15 1/16W 4.3k ohm
R654 119-6801-15 1/16W 68 ohm
R655 119-6801-15 1/16W 68 ohm
R656 119-5611-15 1/16W 560 ohm
R657 032-0140-96 1/10W 120k ohm F
R658 032-0140-55 1/16W 4.7k ohm F
R659 032-0140-89 1/4W 47k ohm F
R662 119-1031-15 1/16W 10k ohm
R663 119-0000-05 1/16W 0 ohm JW
R664 119-5611-15 1/16W 560 ohm
R665 119-2231-15 1/16W 22k ohm
R666 119-4701-15 1/16W 47 ohm
R667 119-4741-15 1/16W 470k ohm
R668 119-4721-15 1/16W 4.7k ohm
R669 119-1031-15 1/16W 10k ohm
R1001 119-1011-15 1/16W 100 ohm
R1002 119-2231-15 1/16W 22k ohm
R1003 119-2231-15 1/16W 22k ohm
R1004 119-1011-15 1/16W 100 ohm
R1005 119-2231-15 1/16W 22k ohm
R1006 119-2231-15 1/16W 22k ohm
R1007 119-5611-15 1/16W 560 ohm
R1008 119-1031-15 1/16W 10k ohm
R1009 032-0140-89 1/4W 47k ohm F
R1010 032-0140-89 1/4W 47k ohm F
R1011 032-0140-89 1/4W 47k ohm F
R1012 032-0140-89 1/4W 47k ohm F
R1013 119-1031-15 1/16W 10k ohm
R1014 119-1031-15 1/16W 10k ohm
R1015 119-1031-15 1/16W 10k ohm
R1016 119-1031-15 1/16W 10k ohm
R1017 032-0140-58 1/16W 51k ohm F
R1018 032-0140-58 1/16W 51k ohm F
R1019 119-1031-15 1/16W 10k ohm
R1020 119-1031-15 1/16W 10k ohm
R1021 119-4731-15 1/16W 47k ohm
R1022 119-4731-15 1/16W 47k ohm
R1023 119-1831-15 1/16W 18k ohm
R1024 119-4731-15 1/16W 47k ohm
R1025 119-1831-15 1/16W 18k ohm
R1026 119-4731-15 1/16W 47k ohm
R1027 119-4731-15 1/16W 47k ohm
R1028 119-1831-15 1/16W 18k ohm
R1029 119-4731-15 1/16W 47k ohm
R1030 119-1831-15 1/16W 18k ohm
R1031 119-4731-15 1/16W 47k ohm
R1032 119-4731-15 1/16W 47k ohm
R1033 119-1031-15 1/16W 10k ohm
R1034 032-0140-58 1/16W 51k ohm F
R1035 032-0140-58 1/16W 51k ohm F
R1036 119-1031-15 1/16W 10k ohm
R1037 119-1831-15 1/16W 18k ohm
R1038 119-1831-15 1/16W 18k ohm
R1039 119-1831-15 1/16W 18k ohm
R1040 119-1831-15 1/16W 18k ohm
R1041 119-2201-15 1/16W 22 ohm
R1042 119-4731-15 1/16W 47k ohm
R1043 119-4721-15 1/16W 4.7k ohm
R1045 119-1021-15 1/16W 1k ohm
R1046 119-8221-15 1/16W 8.2k ohm
R1047 119-1021-15 1/16W 1k ohm
R1048 119-1221-15 1/16W 1.2k ohm
R1049 119-1041-15 1/16W 100k ohm
R1050 119-1241-15 1/16W 120k ohm
R1051 119-3331-15 1/16W 33k ohm
R1052 119-3331-15 1/16W 33k ohm
R1053 119-1841-15 1/16W 180k ohm
R1054 119-1841-15 1/16W 180k ohm
R1055 119-3331-15 1/16W 33k ohm
R1056 119-1021-15 1/16W 1k ohm
R1057 119-2231-15 1/16W 22k ohm
R1058 119-3331-15 1/16W 33k ohm
R1059 119-2231-15 1/16W 22k ohm
R1060 119-4731-15 1/16W 47k ohm
R1061 119-1011-15 1/16W 100 ohm
R1062 119-3331-15 1/16W 33k ohm
R1063 119-3331-15 1/16W 33k ohm
R1064 119-3331-15 1/16W 33k ohm
R1065 119-1521-15 1/16W 1.5k ohm
R1066 119-3331-15 1/16W 33k ohm
R1067 119-1011-15 1/16W 100 ohm
R1068 119-1011-15 1/16W 100 ohm
R1069 119-1031-15 1/16W 10k ohm
R1070 119-1011-15 1/16W 100 ohm
R1071 119-1011-15 1/16W 100 ohm
R1072 119-1021-15 1/16W 1k ohm
R1073 119-1021-15 1/16W 1k ohm
R1075 119-1021-15 1/16W 1k ohm
R1077 119-1021-15 1/16W 1k ohm
R1078 119-1011-15 1/16W 100 ohm
R1079 119-1031-15 1/16W 10k ohm
R1080 119-1031-15 1/16W 10k ohm
R1082 116-1521-15 1/8W 1.5k ohm
R1083 119-2431-15 1/16W 24k ohm
R1084 119-2431-15 1/16W 24k ohm
R1085 119-2431-15 1/16W 24k ohm
R1086 119-2431-15 1/16W 24k ohm
R1087 119-2431-15 1/16W 24k ohm
R1088 119-2431-15 1/16W 24k ohm
R1089 116-1221-15 1/8W 1.2k ohm
R1090 119-4731-15 1/16W 47k ohm
R1091 119-4731-15 1/16W 47k ohm
R1092 119-4731-15 1/16W 47k ohm
R1093 119-4731-15 1/16W 47k ohm
R1094 119-4731-15 1/16W 47k ohm
R1095 119-4731-15 1/16W 47k ohm
R1096 119-1031-15 1/16W 10k ohm
R1099 119-4731-15 1/16W 47k ohm
R1100 119-3631-15 1/16W 36k ohm
R1101 119-3631-15 1/16W 36k ohm
R1102 119-3631-15 1/16W 36k ohm
R1103 119-3631-15 1/16W 36k ohm
R1104 119-3631-15 1/16W 36k ohm
R1105 119-3631-15 1/16W 36k ohm
R1108 119-4731-15 1/16W 47k ohm
R1109 116-1591-15 1/8W 1.5 ohm
R1110 116-1591-15 1/8W 1.5 ohm
R1111 119-3321-15 1/16W 3.3k ohm
R1112 119-2231-15 1/16W 22k ohm
R1113 116-1591-15 1/8W 1.5 ohm
R1114 116-1591-15 1/8W 1.5 ohm
R1117 119-3321-15 1/16W 3.3k ohm
R1119 119-1031-15 1/16W 10k ohm
R1123 119-2231-15 1/16W 22k ohm
R1124 119-2231-15 1/16W 22k ohm
R1125 119-2231-15 1/16W 22k ohm
R1127 119-2231-15 1/16W 22k ohm
R1128 119-2231-15 1/16W 22k ohm
R1129 119-2231-15 1/16W 22k ohm
R1130 119-1021-15 1/16W 1k ohm
R1131 119-1021-15 1/16W 1k ohm
R1132 119-1021-15 1/16W 1k ohm
R1133 119-3311-15 1/16W 330 ohm
R1134 119-3311-15 1/16W 330 ohm
R1135 119-3311-15 1/16W 330 ohm
R1136 119-3311-15 1/16W 330 ohm
R1137 119-3311-15 1/16W 330 ohm
R1138 119-3311-15 1/16W 330 ohm
R1141 119-1021-15 1/16W 1k ohm
R1142 119-1021-15 1/16W 1k ohm
R1143 119-1021-15 1/16W 1k ohm
R1144 119-1231-15 1/16W 12k ohm
R1147 119-4721-15 1/16W 4.7k ohm
R1148 119-3311-15 1/16W 330 ohm
R1149 119-3311-15 1/16W 330 ohm
R1150 119-3311-15 1/16W 330 ohm
R1151 119-3311-15 1/16W 330 ohm
R1152 119-1031-15 1/16W 10k ohm
R1153 119-1031-15 1/16W 10k ohm
R1154 119-2231-15 1/16W 22k ohm
R1155 119-2231-15 1/16W 22k ohm
R1156 119-2231-15 1/16W 22k ohm
R1157 119-2231-15 1/16W 22k ohm
R1158 119-4731-15 1/16W 47k ohm
R1159 032-0140-50 1/16W 10k ohm F
R1160 032-0140-50 1/16W 10k ohm F
R1161 032-0140-50 1/16W 10k ohm F
R1162 032-0140-50 1/16W 10k ohm F
R1163 032-0140-50 1/16W 10k ohm F
R1164 032-0140-50 1/16W 10k ohm F
R1165 032-0140-50 1/16W 10k ohm F
R1166 032-0140-50 1/16W 10k ohm F