Clarke CSR5450BP User manual

USER INSTRUCTIONS
GC0715
BOLTLESS SHELVING
MODEL NO: CSR5450BP/RP/LG
PART NO: 6600524 (BLUE), 6600525 (RED), 6600526 (LIGHT GREY)

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE Boltless Shelving. Before attempting to
assemble this product, please read this manual thoroughly and follow the
instructions carefully. In doing so you will ensure the safety of yourself and that
of others around you, and you can look forward to your purchase giving you
long and satisfactory service. In the event of damage, spare parts are
available from the Clarke International parts department.
UNPACKING & ASSEMBLY
When unpacking, check for damaged or missing parts. Any deficiencies
found should be reported to your CLARKE dealer where the product was
originally purchased. Do not dispose of damaged components or packaging
with general household waste. They should be taken to a recycling centre
and disposed of appropriately.
This product should include the following items:
ASSEMBLY ADVICE
1. Assemble on a firm, level surface. Avoid assembly on a domestic carpet.
2. Use a cloth or softwood block to protect the surface finish of the product
when using a mallet.
3. Always ensure that the tabs sit at the bottom of the keyhole slots.
4. It is recommended that the assembly should be done by two persons.
5. Follow all steps if wishing to create a single 5-shelf unit or ignore steps 6 & 7
if wishing to create two units with only 2/3 shelves.
6. It is recommended that the shelving unit be fixed to an adjacent wall.
7. If required, two free standing benches can be created instead of shelving.
No Description Quantity
ACornerPost 8
B Long Beam 10
C Short Beam 10
D Centre Beam 5
E Shelf 5
F Post Connector 4
G Plastic End Cap 8

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ASSEMBLY
The tabs of the beams will often enter
the slots fully using just firm hand
pressure but if they are too tight, you
may require a rubber mallet to assist.
If so, always use a cloth to protect
the product paint finish. Tap gently
with the mallet to drive the tabs of
the beams fully into the slots in the
corner post. Always strike the edge
close to the post.
1. Decide how high you want the
shelves to be, relative to the floor,
noting that the bottom shelf
should never be more than
150mm from the bottom of the
legs. If it is wished to have the
bottom shelf in a higher position,
then additional beams should be
positioned near the bottom of the
corner posts.
2. Use the short beams to connect
two posts together as in Fig 1.
IMPORTANT: Note that the edge with the wider flange should be installed
uppermost to support the shelf.
3. Repeat this again for the other end assembly, making sure that the
corresponding beams are at the same height.
4. Use the long beams to connect the two end assemblies together as shown
in Fig 2.
5. Connect the centre beams to the
long beams by bending the
flexible tabs to 90 degrees and
slotting them into place as shown
in Fig 3. Finally bend the tabs back
180 degrees to lock in place.

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
6. Fit the post connectors to the
lower corner posts and add the
upper posts as shown in Fig 4.
7. Assemble the upper beams in the
same way as the lower beams.
8. Position the shelves on the beams.
9. Fit the plastic end caps to each
corner post.
SAFETY ADVICE
• Always place heavier items on the lower shelf.
• Always distribute loads evenly across the shelves.
• The shelving unit is not recommended for outdoor use.
• Do not exceed the maximum load of 450kg per shelf.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase. This guarantee is invalid if the product is found to have been
abused or tampered with in any way, or not used for its intended purpose.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
CLARKE INTERNATIONAL HEMNALL STREET, EPPING, ESSEX CM16 4LG