Clarke CSR4350LG User manual

ASSEMBLY INSTRUCTIONS
GC0417
4-SHELF BOLTLESS SHELVING UNITS
MODEL NO: CSR4350
PART NO: SEE TABLE PAGE 2

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE Shelving Unit.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
Please keep these instructions in a safe place for future reference.
SCOPE
These instructions cover the following models
Description Model Part Number
4-Shelf 350kg Boltless Shelving (Light Grey) CSR4350/60LG 6600722
4-Shelf 350kg Boltless Shelving (Blue) CSR4350/60BL 6600724

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INVENTORY
No Description Quantity
ACornerPost 8
BLongBeam 8
CShortBeam 8
DSupportBeam 8
E Shelf 4
FFoot 4
G Post Joining Insert 4

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
ASSEMBLY INSTRUCTIONS
1. Assemble on a strong, level surface. Avoid assembly on a domestic carpet.
2. Use a cloth or softwood block to protect the surface finish of the product
when using a mallet. Strike the flat surface of each beam to prevent
damage to the beam.
3. Always ensure that the rivets sit at the bottom of the keyhole slots.
4. It is recommended that the assembly should be done by two persons.
5. Always wear gloves when assembling the shelving unit.
6. The shelving unit is not recommended for outdoor use.
TOOLS REQUIRED
• Rubber mallet or hammer
• Protective cloth/wood block
ASSEMBLY PROCEDURE
The tabs of the beams will often enter
the slots fully using just firm hand
pressure but if they are too tight, you
may require a rubber mallet to assist.
If so, always use a cloth to protect
the product paint finish.
Tap gently with the mallet to drive the
tabs of the beams fully into the slots in
the post. Always strike the edge close
to the post.
1. Use the short beams (C) to
connect the front and rear posts
together.
• The edge with the wider flange
should be installed uppermost to
support the shelf.
• Leave a gap of 150mm below the
bottom beam and the ground.
2. Repeat this again to create the
other end assembly, making sure
that the corresponding beams are at the same height.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
3. Join the two end assemblies
together with the long beams (B).
• The beams should be spaced
equally with the top beam level
with the top of the posts.
4. Connect the support beams (D) to
the long beams. First bend the
flexible tabs 90 degrees to pass
them through the slots in the long
beams.
• The tab initially lays flat against the
long beam.
5. Next, bend the tab back through
180 degrees to grip the long
beam.
• Use a screwdriver or similar tool to
bend the tabs.
6. Finally bend the tabs back
through 90 degrees the opposite
way to seat tightly against the
support beam.
• Ensure there is no movement
between the beams.
7. Fit post joining inserts (G) into the
posts (A), ensuring that the inserts
are fitted with their tabs to match
the slots of the posts.
8. Construct the upper end
assemblies on the post inserts (G)
before adding more long beams
and support beams as previously
to complete the framework.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
9. Lay the shelf panels (E) into
position.
• Always assemble the top shelf at
the highest possible position.
10. Insert the foot (F) into the end of
each post (A).
11. We recommend that the racking
be secured to an adjacent wall
using typical wall insert plugs and
screws (not supplied), aligned with
the assembly slots in the posts.
ENVIRONMENTAL PROTECTION
Do not dispose of old products or damaged parts with general household
waste. All tools, accessories and packaging no longer required should be
sorted, taken to a recycling centre and disposed of appropriately.

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
GENERAL SAFETY RULES
1. Always maintain equipment in good condition for the best/safest
performance.
2. Never exceed the maximum load for these shelving units as stated in the
specification.
3. Never use these units if they are damaged.
4. Always load small, stable items on the top shelves, heavier and bulky items
should be stored on the lower shelves.
5. Always distribute heavy loads evenly across the shelves.
6. Always locate on a strong, level floor surface. Allow adequate working
space.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
SPECIFICATIONS
Model Dimensions
(W x D x H)
Weight
(Empty)
Load per
shelf (evenly
distributed)
CSR4350 1600 x 600 x 1850 mm 46 kg 350 kg