Clas Ohlson JF8010-UK User manual

SUOMINORSKSVENSKAENGLISH
LED Set





Art.no. Model
18-2019 JF8010-UK
36-3587 JF8010




ENGLISH
LED Set

  
Please read the entire instruction manual before using and save it for future
use. We apologise for any text or photo errors and any changes of technical
data. If you have any questions concerning technical problems please
contact our Customer Service Department (see address on reverse.)
Important safety information
These LED spotlights operate on low voltage (1 V). Never connect LED
spotlights directly to the mains.
The enclosed transformer has a 1 V output, so it is safe to install these
LED spotlights yourself. Disconnect the transformer from the socket before
assembling the cables and LED spotlights.
Mount the transformer so that it is not exposed to humidity or steam.
The enclosed transformer provides an output voltage of 1 V that is safe to
work with, but bear this in mind:
• The transformer, the outlet it is connected to and the junction box MUST
be mounted on a dry and well protected location indoors. Do not expose
any included components to liquids of any kind.
• The transformer contains no parts that might need adjusting or are
replaceable. It must be destroyed if it is defective.
• Do not modify the transformer or any component connected to it.
• Never exceed the recommended number of connected LED spotlights
that may be connected safely to the transformer. This set can be
expanded to ten LED spotlights of the same kind (our art. no. 6-588).
• Never overload the transformer; consult with a professional if you are
not sure.


ENGLISH




The box contains
1. (x) LED spotlights (IP66 classed), with a 5-metre mounted lead.
. (1x) 1 V transformer (for indoor use).
. (1x) Junction box, with a 10-metre cable.
. (10x) blanking plugs mounted in the sockets on
the extension xture.
5. Dusk to Dawn sensor with 5-metre lead.

5
ENGLISH
Arrangement and installation
Give some thought to the arrangement of the spotlights. Do not pull the
cables and protect against dampness. Place the junction box and the leads
so they do not become damaged or cause a hazard (risk of tripping). Even
if the components are assembled protected against wind and weather, the
transform can be short-circuited if the cables become damaged.

Transformer
1. Mount the junction box in a suitable place so that the transformer can be
connected to a socket indoors in a protected location. Make sure that the
transformer is in reach of the junction box’s connecting cable. 

. Arrange the LED spotlights temporarily in a suitable place. Make sure
that the cables can reach the junction box. Extra LED spotlights can be
purchased (Art. No. 6-588).
Junction box
Dusk Down Sensor
Mounting holes
LED spotlights


6
ENGLISH
. When you are satised that the spotlights are placed right, drill Ø  mm
holes (See Fig. ).
. Feed the spotlight connecting cable through the drilled hole (See Fig. 1).
5. Insert the LED spotlight into the holes.
6. Drill a Ø 1 mm hole for the Dusk to Dawn sensor (see Fig. ).
Ø 1 mm hole


 mm
 mm


ENGLISH
. Insert sensor into the hole (see Fig. ).
8. Fasten the dusk to Dawn sensor in the hole.
9. Remove as many blanking plugs in the junction box as you have LED
spotlights. Insert the connectors as far as you can into the junction
box. The + sign on a connectors should match with the + marking on
the junction box (See Fig.5). Blanking plugs should be mounted on all
unused sockets on the junction box to protect against moisture.
Lead from Dusk to
Dawn sensor
Blanking plug

Leads from LED spotlights
Clear cap
Sensor



8
ENGLISH
10. Mount the junction box with screws (not included) with the sockets facing
downwards (see Fig. 6).
11. Connect the junction box cable to the transformer and tighten the cable
gland nut. Now connect the transformer to a wall socket (see Fig. ).
Screws

Low voltagecable
to junction box
Wall socket
Transformer


9
ENGLISH
Specifications

In: 0 V~50 Hz, 0.1 A
Out: 1 V~500 mA, 6 VA
Intended for indoor use.

Sleeve IP66
Mounting holes Ø  mm at least 6 mm deep
Outer diameter Ø  mm
Cable length 5 m
A maximum of 10 can be connected to the junction box.

10 outlets
10-metreconnecting lead (to transformer)

Cable length: 5 m
Hole: Ø 1 mm
Extra LED spotlights can be purchased, our Art. No. 6-588.
Disposal
Follow local ordinances when disposing of this product. If you are unsure
about how to dispose of this product contact your municipality.

10
SVENSKA
LED-set

  
Läs igenom hela bruksanvisningen före användning och spara den sedan
för framtida bruk. Vi reserverar oss för ev. text- och bildfel samt ändringar av
tekniska data. Vid tekniska eller andra frågor kan Du kontakta oss
(se adresserna på baksidan).
Viktig säkerhetsinformation
Dessa LED-spotlights drivs av lågspänning (1 V). Anslut aldrig LED-
spotlight direkt till ett eluttag.
Den bifogade transformatorn ger 1 V utspänning som gör det säkert att
installera dessa LED-spotlights själv. Dra ur transformatorn ur el-uttaget
innan montering av kablar och LED-spotlights.
Montera transformatorn så att den inte utsätts för fukt eller ånga.
Den bifogade transformatorn ger 1 V utspänning som är säkert att hantera,
men tänk på detta:
• Transformatorn och el-uttaget som den är ansluten till MÅSTE monteras
på en torr och väl skyddad plats inomhus. Utsätt inte några ingående
komponenter för vätskor av någon typ.
• Kopplingsboxen kan monteras både inom- och utomhus. Vid montering
utomhus måste den vara skyddad från regn och snö.”
• Transformatorn innehåller inga delar som kan justeras eller bytas ut,
den måste kasseras om den är defekt.
• Ändra inte transformatorn eller någon komponent som är ansluten
till den.
• Överskrid aldrig anslutna rekommenderat antal LED-spotlights som
kan anslutas säkert till transformatorn, detta set är utbyggbart till tio
LED-spotlights av samma typ (vårt art.nr. 6-588)
• Överbelasta aldrig transformatorn. Rådgör med en fackman om du
är tveksam.