Classic Exhibits visionary designs MOD-1529 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Front View Back View
MOD-1529 Reception Counter
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Step 1 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
1
5
5
5A
5A
8
6
7
7A
7B
6A
Door Door
2
3
4
Completed Counter
Base Assembly
(Front View)
Back View Back View Back View
Infill
Infill
Infill
Infill
Shelf
Shelf Support
Shelf Support
Item
1
2
3
4
5/5A
6/6A/7/7A/7B
8
Qty.
1
1
1
1
2/2
1/1/1/1/1
1
Description
37.5”h S44 Vertical Extrusion
37.5”h S44 Vertical Extrusion
37.5”h S44 Vertical Extrusion
37.5”h S44 Vertical Extrusion
18.5”w Z45 Horizontal Extrusion
46”w Z45 Horizontal Extrusion
33.917”h Z45 Vertical Extrusion
Steps:
1) Connect lower horizontals [5,6,7] between verticals [1,2,3,4].
2) Attach vertical [8] to lower horizontal [6].
3) Slide Infills between verticals [1,2] and [3,4].
4) Slide lower Infill between verticals [2] and [3].
5) Connect horizontal [7A] between verticals [2,3].
6) Slide Infill between verticals [2] and [3] and on top of horizontal [7A].
7) Connect Shelf Supports to Velcro on side Infills, then place Shelf
on top of supports.
8) Connect Doors to verticals [1] and [4]. See Door Attachment detail.
9) Connect upper horizontals [5A,6A,7B] between verticals [1,2,3,4]
and on top of Infills and Doors.
*
*
*
*
Shelf Support
Shelf Support
1
2
4
1
4
3
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
Counter Assembly

© 2023
Step 2 of 3
Order #XXXXX
Using Your Setup Instructions
The Aero Setup Instructions are created specifically for your configuration. The instructions include an
exploded view of the frame which is sequentially labeled. We encourage you to review the instructions
before attempting to assemble your exhibit.
Connections are kept very simple; no tools required. Everything assembles with push-button connectors.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Push-Button
Push-Button
66
6
6
Numbered Label
Connections are made by holding the button down and
sliding the red tube into opposing tube until button locks
into the hole of the opposing tube. To disassemble, push button
and pull or twist extrusions apart.
Locked layer contains
placeholder marks.
Connect in alphabetical order as shown.
A
C
D
E
G
H
F
B
Aero Frame Assembly

© 2023
Step 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
9
10
11
10A
11A
9A
3
2
Item
9/9A
10/10A
11/11A
Qty.
1/1
1/1
1/1
Description
15.28” TSP46 Curved Extrusion
30.382”w TSP46 Horizontal Extrusion
30.382”w TSP46 Horizontal Extrusion
Steps:
1) Connect extrusions [9,9A,10,10A,11,11A] together. See TSP46 Corner Connection detail.
3) Slide Aero frame assemblies into the groove of front verticals [2,3].
4) Place counter top on top of assembled base. See Counter Top Attachment detail.
5) Attach SEG frame to verticals [2] & [3], using standoff caps.
6) Attach SEG graphic to SEG frame. See SEG Graphic Installation detail.
Counter Top
Aero
Frame
Assembled Base
Aero
Frame
SEG Frame
Completed Assembly
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
*
*
*
*
*
*
*
Lock
Set Screw
Slide end of Extrusion over
Lock. Tighten Set Screw to
secure Extrusions.
TSP46 Corner Connection
SEG Frame Assembly
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner, then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Counter Assembly (cont’d)