Classic Exhibits VISIONARY DESIGNS VK-3006 Manual

© 2017
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-3006 - 10’ x 30’ Inline Display
Plan View
10’
30’

© 2017
Order #XXXXX General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED

© 2017
Order #XXXXX
Step 1 of 12
Closet Assembly
When assembled
Top View
S44
PR37
Velcro
Steps:
1) Connect PR37 to verticals [4,7], as shown.
Note: PR37 should remain attached to verticals
during disassembly.
2) Attach lower horizontals [12,14,15] & Door Threshold
between verticals [4,5,6,7,8,9,10,11] as shown, &
connect horizontal [13] between verticals [4,11].
See Door Threshold Attachment detail.
3) Slide Infills between verticals; secure with upper
horizontals [12A,13A,14A,15A].
**
Item
4
5,6,7
8,9,10
11
12/12A
13/13A
14/14A
15/15A
--
--
Qty.
1
1,1,1
1,1,1
1
3/3
1/1
1/1
3/3
1
2
Description
96”h S44 Vertical Extrusion w/ Door Stop
96”h S44 Vertical Extrusion
96”h S44 Vertical Extrusion
96”h S44 Vertical Extrusion w/ Door Hinge
22.126”w Z45 Horizontal Extrusion
22.5”w Z45 Horizontal Extrusion
22.5”w Z45 Horizontal Extrusion
22.126”w Z45 Horizontal Extrusion
Door Threshold
92.4”h PR37 Vertical Extrusion
4
5
6
7
8
9
10
11
12A
15A
15A
15A
13
13A
14
14A
12A
12A
12
15
Door
Threshold 15
15
12
12
I
n
f
ill
I
n
f
ill
I
n
f
ill
I
nfil
lI
n
f
ill
I
n
f
ill
I
nfi
l
l
I
nfi
l
l
Slide PR37 extrusion into
groove of vertical and tighten
set screw to secure in place.
PR37
Extrusion
Profile
Velcro
Door Threshold
Tighten
setscrew
to secure
Slide Connector
into Groove
of Extrusion
Door Threshold
Attachment
*
Top View
S44 PR37
Velcro

© 2017
Order #XXXXX
Step 2 of 12
Closet Attachments
Caps
Monitor
Mount
Steps:
1) Install Door to Vertical [11]. See Door Attachment detail.
2) Attach Monitor Mount to Verticals [9,10].
See Monitor Mount Attachment detail.
3) Connect Header Graphic to Verticals [8,9,10,11] using
screw caps. See Header Attachment detail.
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
*Monitor Mount Attachment
Bolt
Monitor
Mount
Stand-Off
Barrel
V4
Connectors
Attach Monitor Mount to V4 Connectors
using bolts.
Slide V4 Connections into vertical
channel of extrusions. Tighten set
screw to secure.
Graphic
V4 Connector
Slide V4 connector into groove. Tighten set
screw to secure V4. Insert screw cap through
hole of graphic & into V4 connector.
Tighten screw cap to secure in place.
Header Attachment
Screw Cap
*
Header Graphic
D
o
o
r
**
****
****
*
*
11
10
9
8

© 2017
Order #XXXXX
Step 3 of 12
Left Backwall Assembly
4
When assembled
Item
1
2
16
17/17A
18/18A
--
Qty.
1
1
1
1/1
1/1
3
Description
Boomerang Foot
96”h S44 Vertical Extrusion
96”h S44 Vertical Extrusion
40”w Z45 Horizontal Extrusion
96” Z45 curved Horizontal Extrusion
92.4”h PR37 Vertical Extrusion
Steps:
1) Connect PR37 to verticals [2,16], as shown.
Note: PR37 should remain attached to verticals
during disassembly.
2) Attach Boomerang Foot [1] to vertical [2].
See Boomerang Foot Attachment detail.
3) Attach horizontals [17,17A,18,18A] between
verticals [4,16,2] as shown.
4) Apply fabric graphic to back side of frame
assembly, using Velcro.
Slide PR37 extrusion
into groove of vertical
and tighten set screw
to secure in place.
PR37
Extrusion
Profile
Velcro
Boomerang Foot Attachment
Bolt
set
screw
Foot
Vertical
*
Attach foot with Bolts.
Slide V4 Connectors
into groove of vertical
extrusion & tighten
set screw to secure.
V4
1
16
2
17
17A
18A
18
*
Attach graphic
to velcro on back of
assembled frame
Top View
S44 PR37
PR37
VelcroVelcro
Top View
S44 PR37
Velcro

© 2017
Order #XXXXX
Step 4 of 12
Right Backwall Assembly
7
When assembled
Item
1
2A
19
20/20A
21/21A
--
Qty.
1
1
1
1/1
1/1
3
Description
Boomerang Foot
96”h S44 Vertical Extrusion
96”h S44 Vertical Extrusion
40”w Z45 Horizontal Extrusion
96” Z45 curved Horizontal Extrusion
92.4”h PR37 Vertical Extrusion
Steps:
1) Connect PR37 to verticals [2A,19], as shown.
Note: PR37 should remain attached to verticals
during disassembly.
2) Attach Boomerang Foot [1] to vertical [2A].
See Boomerang Foot Attachment detail.
3) Attach horizontals [20,20A,21,21A] between
verticals [7,19,2A] as shown.
4) Apply fabric graphic to back side of frame
assembly, using Velcro.
Slide PR37 extrusion
into groove of vertical
and tighten set screw
to secure in place.
PR37
Extrusion
Profile
Velcro
Boomerang Foot Attachment
Bolt
set
screw
Foot
Vertical
*
Attach foot with Bolts.
Slide V4 Connectors
into groove of vertical
extrusion & tighten
set screw to secure.
V4
1
19
2A
20
21A
20A
21 *
Attach graphic
to velcro on back of
assembled frame
Top View
S44 PR37
PR37
VelcroVelcro
Top View
S44
PR37
Velcro

© 2017
Order #XXXXX
Step 5 of 12
Left Aero Ring Assembly
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
1
2
13
14
11
12
3
15
16
10 4
17
9
18
5
19
20
8
6
7
When assembled
Steps:
1) Assemble Aero frame parts together
in numerical order, as shown.
2) Attach pillowcase graphic to assembled
frame.

© 2017
Order #XXXXX
Step 6 of 12
Right Aero Ring Assembly
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
1
2
13
14
11
12
3
15
16
10 4
17
9
18
5
19
20
8
6
7
Steps:
1) Assemble Aero frame parts together
in numerical order, as shown.
2) Attach pillowcase graphic to assembled
frame.
When assembled

© 2017
Order #XXXXX
Step 7 of 12
Workstation Assembly
When assembled
Item
1
2
3
4
5
6
7
8
9/9A/9B
10/10A
11/11A
12
Qty.
4
4
4
4
4
4
4
4
4/4/4
4/4
4/4
4
Description
66”h S40 Vertical Extrusion
66”h S40 Vertical Extrusion
36”h S40 Vertical Extrusion w/ Door Hinge
36”h S40 Vertical Extrusion w/ Door Stop
40.975” S40 curved Vertical Extrusion
40.975” S40 curved Vertical Extrusion
5.24”w Z32 Horizontal Extrusion w/ mitred end
5.24”w Z32 Horizontal Extrusion w/ mitred end
18.5”w S40 Horizontal Extrusion
18.5”w S40 Horizontal Extrusion
18.5”w S40 Horizontal Extrusion
21.02” x 4.5” Mounting Plate
Steps:
1) Connect curved extrusions [5,6] between
verticals [1,2,3,4] using horizontals [7,8].
2) Attach lower horizontal [9] between
verticals [1,2]; connect lower horizontal [10]
between verticals [3,4].
3) Attach Door between verticals [3,4].
See Door Attachment detail.
4) Slide lower infills between verticals &
curved extrusions as shown; secure with
horizontals [9A,10A,11,11A].
5) Place Shelf inside assembly.
6) Place Counter Top onto assembly, sliding
over verticals [1,2].
7) Slide upper infill between verticals [1,2];
secure with upper horizontal [9B].
8) Attach Mountng Plate [12] to verticals [1,2];
& install Monitor Mount. See Monitor Mount
Attachment detail.
Repeat steps 1 thorugh 8 for other three
workstations.
QTY 4
9A
10A
11
11A
1
2
3
4
5
7
8
9
10
6
I
n
f
i
ll
I
n
f
i
l
l
I
n
f
i
l
l
Shelf
Counter
Top
D
oo
r
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
Then attach
wall plate to plate
using bolts and wing nuts
Install V4 connectors to verticals;
secure with setscrew. Attach
mounting plate to connectors.
Monitor Mount Attachment
V4
connectors *
*
*
I
n
f
i
ll
9B
12
*Monitor
Mount
infill
S10
S10 Extrusion
Attached to
Counter Top

© 2017
Order #XXXXX
Step 8 of 12
Workstation to Aero Ring Connection
**
Slide V4 connectors into groove of
horizontal extrusion. Tighten
set screws to secure V4 in place.
Attach bracket to V4 using bolt.
When assembled
Custom Bracket Connection
V4
bolt
set
screw
Bracket
S40 Extrusion
Aero Frame
Steps:
1) Slide assembled Kiosks over Aero frame.
2) Connect Aero Frame to Kiosks using custom bracket.
See Custom Bracket Connection detail.
Repeat steps 1 & 2 for other Aero Frame.
**
*
QTY 2