Claypaky C71050 User manual

1
INSTRUCTIONS ANUAL
Congratulations on choosing a Clay Paky product!
We thank you for your choice. Please note that this product,
as all the others in the rich Clay Paky range, has been
designed and manufactured with total quality to ensure
e cellent performance and best meet your e pectations and
requirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference.
It is essential to know the information and comply with the
instructions given in this manual in order to ensure the fitting is
installed, used and serviced correctly and safely.
CLAY PA Y S.p.A. disclaims all liability for damage to the
fitting or to the other property or persons deriving from
installation, use and maintenance that have not been carried
out in conformity with this instructions manual, which must
always accompany the fitting.
CLAY PA Y S.p.A. reserves the right to modify the
characteristics stated in this instructions manual at any time and
without prior notice.
CONTENTS
Page
2
3
3
4
7
13
13
14
15
16
16
17
PRELI INARY
Contents
Safety information
Unpacking and preparation
Installation and start-up
Control panel
Main menu
Manual zoom
Maintenance
Battery removal
Optional accessories
Technical data
Cause and solution of problems
Channel functions
GLOW UP
& FLIGHT CASE
C C71050
TW C71055
W C71060
F21230
®
ITALIANO
All manuals and user guides at all-guides.com
all-guides.com

2
GLOW UP
• Installation
Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of
anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that,
if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used,
it needs to be replaced with a genuine spare.
• inimum distance of illuminated objects
The projector needs to be positioned so that the objects hit by the beam of light are at least 0.2
metres (8’ 2”) from the lens of the projector.
• inimum distance from flammable materials
The projector must be positioned so that any flammable materials are at least 0.20 metres (8") from
every point on the surface of the fitting.
• ounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
• aximum ambient temperature
Do not use the project if ambient temperature (Ta) exceeds 40°C.
• IP65 protection rating
The equipment is fully protected against dust (first digit 6) and against jets of water (second digit 5).
• Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.
• Connection to the power mains
A qualified electrician must perform connection to the power mains.
Check that the mains frequency and voltage correspond to the frequency and voltage for which the
projector was designed and indicated on the electrical data label.
This label also gives the input power. Refer to the latter to evaluate the maximum number of
devices to be connected to the mains to avoid overloads.
• External surface temperature
The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is 90°C (320°F).
• aintenance
Before starting any maintenance work or cleaning the projector, cut off power from the supply
mains. After switching off, do not remove any parts of the fitting for at least 10 minutes. The lenses
must be mounted and, if visibly damaged, they have to be replaced with genuine spares.
• Battery
This product contains a lithium iron tetraphosphate rechargeable battery. To protect the
environment, please discard the battery at the end of its life cycle according to current law.
Instructions on how to remove the battery from the equipment are available at www.claypaky.it.
SAFETY INFOR ATION
The products referred to in this manual conform to the European Community Directives to which
they are subject:
•Low Voltage Directive 2006/95/EC
•Electromagnetic Compatibility Directive 2004/108/EC
0.2
90°C
IP65
LiFePo
All manuals and user guides at all-guides.com

3
GLOW UP
UNPACKING AND PREPARATION
Packing content - Fig. 1
2
Projector installation - Fig. 2
The projector can be installed on the floor resting on specific rubber feet, on a truss, on the ceiling or wall.
WARNING: the safety chain must be installed except when the projector rests on the floor. (Code 105015/801 available upon request). This
must be secured to the projector support structure and then hooked to the fastening point at the centre of the base.
1
2
3
2
3
14
3
Connecting and disconnecting the power cord - Fig. 3
When connecting the power cord the user can choose whether to use the GlowUp in one of the following ways:
1) Power cord connected for battery charge.
2) Power cord connected for projector power (thus bypassing battery operations).
The GlowUp cannot work in both ways simultaneously.
INSTALLATION AND START-UP
099114 OPTIONAL ACCESSORY C71110
1
All manuals and user guides at all-guides.com

4
GLOW UP
Switching on the projector - Fig. 6
The projector immediately turns on when the power cord is plugged in or, if used in battery mode, by pressing and holding down keys
A
and
S
for
several seconds.
Clay Paky GLOW UP Address xxx BAT xx%
GLOW UP Software release x.x x xxxxx ??? *
The control panel (Figure 8) has a display and buttons for complete programming and management of the projector menu.
The display can be in one of two conditions: idle status and settings status.
When idle, the projector DMX address and percent battery charge are displayed.
If no button is pressed after a wait period (about 60 seconds) when in menu settings status, the display automatically returns to idle status. It should
be noted that when this condition occurs, any modified value that has not yet been confirmed with the
A
key will be cancelled.
To turn off the GlowUP, hold down keys
A
and
S
for several seconds. A confirmation message will appear (Switch off?).
Press
A
-Yes to turn off the GlowUP or press
S
-NO to return to the settings menu.
CONTROL PANEL
6
Connections to the power mains - Fig. 4
L
N
DMX 512
Power Supply
4
5
SIGNAL
SCREEN
DMX 512
5 PIN
1
2
3
4
5
SIGNAL
SCREEN
1
3
2
DMX 512
3 PIN
SIGNAL
SIGNAL
Connections to the control signal line (D X) - Fig. 5
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ω characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. End connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted on the last projector with a resistance of 120 Ω(minimum 1/4 W) between terminals 2 and 3.
I PORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing must be connected to the shield
braid and pin 1 of the connectors.
*see pag. 5
Display symbology
All manuals and user guides at all-guides.com

5
GLOW UP
Continued ➔
Initial projector address settings
An initial address must be set on each single project for the control signal.
Address settings: see page 9.
Button functions – enu use
ENU USE:
1) Press the
S
key once – the various Menu items appear on the display.
2) Press the
B
and DOWN
C
keys to select the menu to be opened:
• Stand Alone: Stand alone operating mode settings
• Radio: Wireless operating mode settings
• Setup (Setup Menu): Channel mode and projector address settings
• Information (Information Menu): To read counters, software version and other information.
• Manual control: (Manual control Menu): Activates test and manual control functions.
• Advanced (Advanced Menu): ADVANCED Menu use is recommended for qualified technical personnel.
To open the ADVANCED menu, see page 11.
3) Press the
F
key to display the first item in the selected menu.
4) Use the UP
B
and DOWN
C
keys to select menu items.
• If pressed in idle status: Cyclically switches between idle status and menu settings.
• If pressed while setting a menu: Moves to an upper level without changing anything (exits the function)
Decreases the value displayed (with auto-repetitions), or passes to the next item on the menu
For quick access to the minimum parameter value, press the UP key while holding down the DOWN key.
Increases the value displayed (with auto-repetitions), or passes to the previous item on the menu
For quick access to the maximum parameter value, press the DOWN key while holding down the UP key.
Confirms the displayed value or activates the displayed function or opens the next menu.
SELECT
DOWN
UP
ENTER
Transmission to DMX cable
Reception from DMX cable
Reception DMX from Radio (wireless)
Transmission DMX from Radio (wireless)
Display symbology
All manuals and user guides at all-guides.com

GLOW UP
6
4
3
1
2
1
2
Fuse 6,3x32mm
10AT 250Vac
(030470)
Fuse 6,3x32mm
3AT 250Vac
(030471)
9
8
Charging glow up - Fig. 8
From 1 to 6 Glow Ups can be simultaneously charged by appropriately connecting and powering the flight-case.
Replacing flight case fuses - Fig. 9
Each flight-case has 2 fuses associated with the main power cord connection and one fuse for each Glow UP charge station.
All manuals and user guides at all-guides.com
all-guides.com

C TW
7
GLOW UP
AIN ENU
ENU SETTING
Stand Alone
1
Continued ➔
Edit scene
Edit chase
DMX
recorder
Play chase
Play DMX
recorder
SetUp
4
DMX
Address
DMX Mode
Color Mode
Backlight
Display
contrast
Factory
Advanced
6
System
Errors
CPU Reset
Test
Change
Model
FW
Uploader
Battery
Select
Radio
2
Unlink
from TX
Add RX
Disconnect
all RX
3
Manual
Control
Green Dimmer Stop
Strobe
Dimmer
Stop
Strobe
Macro
Color
Macro
Timing
Macro
Fading
Red Tunable
white Dimmer
C TW W
Blue Stop
Strobe
White
5
Partial LED
hours
Charge
Battery num.
System
version
LED
temperature
Battery
voltage
Battery
temperature
Product ID
Channel
monitor
Total LED
hours
Charge
Battery hours
Discharge
Battery hours
Information
Color temp
All manuals and user guides at all-guides.com

8
GLOW UP
EDIT SCENE
To create/overwrite/modify a SCENE customised by the user:
1) Press ENTER
A
– SCENE 1 appears on the display.
2) Use the UP
B
and DOWN
C
keys to select from the ten available
SCENES.
3) Press ENTER
A
to open a SCENE.
4) A value can be associated with each GlowUp channel inside each
SCENE using the UP
B
and DOWN
C
keys.
5) When finished with settings, press SELECT
S
. A confirmation
message appears: SAVE SCENE X ?.
6) Press ENTER
A
to confirm and save the SCENE or SELECT
S
to
return to the previous menu.
EDIT CHASE
To create a CHASE made up of a series of SCENES saved by the user.
1) Press ENTER
A
– STEP 1 appears on the display.
2) Use the UP
B
and DOWN
C
keys to select the STEP to be
attributed a SCENE.
3) Press ENTER
A
and use the UP
B
and DOWN
C
keys to select
the SCENE to be imported (SC0..or NONE).
4) Press ENTER
A
to confirm the selection or SELECT
S
to return to
the previous menu.
D X RECORDER
To record a scene sequence programmed on the unit.
PLAY CHASE
Starts CHASE playback (created with EDIT CHASE).
Press ENTER
A
and CHASE to display the sequence of STEPS
PLAY D X RECORDER
Starts program playback (created/recorded with DMX RECORDER).
Press ENTER
A
to run the program.
Assigns the desired command to the GlowUP Radio module
1) Press ENTER
A
– current settings appear on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following
settings:
Add RX – Connected to all free receivers
Disconnect all RX – Disconnected from all receivers
Unlink from TX – Disconnected from the transmitter
3) Press ENTER
A
to confirm the selection (the display blinks for
several seconds) or SELECT
S
to keep the current settings and
return to the previous Menu.
STAND ALONE ENU
RADIO ENU
Stand Alone Edit scene
Edit chase
DMX
recorder
Radio Unlink
from TX
Add RX
Disconnect
all RX
Play chase
Play DMX
recorder
All manuals and user guides at all-guides.com

9
GLOW UP
Allows the user to set a level for each of the following channels in BIT from
the control panel:
GLOWUP C GLOWUP TW GLOWUP W
Red Tunable white Dimmer
Green Dimmer Stop Strobe
Blue Stop Strobe
White
Dimmer
Strop Strobe
acro Color
acro Timing
acro Fading
1) Press ENTER
A
– the first channel (RED) appears on the display.
2) Use the UP
B
and DOWN
C
keys to select the concerned channel.
3) Press ENTER
A
and use the UP
B
and DOWN
C
keys to assign
the DMX level to the selected channel (value between 0 and 255).
4) Press SELECT
S
to return to the previous Menu.
D X ADDRESS
Allows the user to set the DMX address to be assigned to the projector.
1) Press ENTER
A
– the current DMX address appears on the display.
2) Use the UP
B
and DOWN
C
keys to set the DMX address.
3) Press ENTER
A
to confirm the selection (the display blinks for
several seconds) or SELECT
S
to keep the current settings and
return to the previous Menu.
D X ODE
Allows the user to set the receiver/transmission mode to be assigned to
the projector.
1) Press ENTER
A
– current settings appear on the display.
2) Use the UP
B
and DOWN
C
keys to select the mode to be
assigned to GLOW UP from those available:
Slave Cable – Receiver from DMX cable
Slave Wireless – Receiver from wireless
Stand Alone – STAND ALONE operating mode
aster Cable – Transmitter via DMX cable
aster Wireless - Transmitter via wireless
aster Cable + Wireless – Transmitter via DMX cable + wireless
Repeater Cable – Repeater from DMX cable to wireless
Repeater Wireless – Repeater from wireless to DMX cable
3) Press ENTER
A
to confirm the selection (the display blinks for
several seconds) or SELECT
S
to keep the current settings and
return to the previous Menu.
COLOR ODE (GLOWUP C)
Allows the user to select the color
mixing system.
1) Press ENTER
A
– current
settings appear on the display.
2) Use the UP
B
and DOWN
C
keys to select RGB or
CMY.
3) Press ENTER
A
to confirm
the selection (the display
blinks for several seconds) or
SELECT
S
to keep the
current settings and return to
the previous Menu.
ANUAL CONTROL ENU
Continued ➔
Manual
Control
Green
Dimmer
Stop
Strobe
Macro
Color
Macro
Timing
Macro
Fading
Red
Blue
White
SetUp DMX
Address
DMX Mode
Color Mode
SET UP ENU
C TW W
C TW
Dimmer Stop
Strobe
Tunable
white Dimmer
Stop
Strobe
Color
temperature
COLOR TE P (GLOWUP TW)
Allows the user to select the color
mixing system.
1) Press ENTER
A
– current
settings appear on the display.
2) Use the UP
B
and DOWN
C
keys to select Independent mode
or Constant intensity mode or
ax intensity mode.
3) Press ENTER
A
to confirm the
selection (the display blinks for
several seconds) or SELECT
S
to keep the current settings and
return to the previous Menu.
All manuals and user guides at all-guides.com

GLOW UP
BACKLIGHT
Used to turn off display backlight 60 seconds after switching to idle status.
To turn back on, simply press any key.
1) Press ENTER
A
– current settings appear on the display.
2) Use the UP
B
and DOWN
C
keys to turn display backlight OFF or ON.
3) Press ENTER
A
to confirm the selection (the display blinks for
several seconds) or SELECT
S
to keep the current settings and
return to the previous Menu.
DISPLAY CONTRAST
Lets the user modify display contrast.
1) Press ENTER
A
– current settings appear on the display.
2) Use the UP
B
and DOWN
C
keys to modify the value from 0 to 10
according to the desired contrast.
3) Press SELECT
S
to return to the previous Menu.
FACTORY
Used for restoring default values on all options menu items and relevant
submenus.
1) Press ENTER
A
– a confirmation message appears on the display (Ok?)
2) Press ENTER
A
to confirm the selection (the display blinks for
several seconds) or SELECT
S
to keep the current settings.
TOTAL LED HOURS
Displays total LED working hours.
1) Press ENTER
A
– total LED working hours appear on the display.
2) Press SELECT
S
to return to the previous Menu.
PARTIAL LED HOURS
Displays partial LED working hours.
1) Press ENTER
A
– partial LED working hours appear on the display.
2) To reset partial LED working hours, simultaneously press and hold
down the UP
B
and DOWN
C
keys for several seconds. When
“Rst?” (Reset) appears, confirm by pressing ENTER
A
.
3) Press SELECT
S
to return to the previous Menu.
CHARGE BATTERY HOURS
Displays total hours from the last battery charge.
1) Press ENTER
A
– total charge hours appear on the display.
2) Press SELECT
S
to return to the previous Menu.
DISCHARGE BATTERY HOURS
Displays total GlowUp battery powered operating hours from last time
used.
1) Press ENTER
A
– total battery powered operating hours appear on
the display.
2) Press SELECT
S
to return to the previous Menu.
CHARGE BATTERY NU BER
Displays the number of Glow UP battery charge cycles.
1) Press ENTER
A
– the number of charge cycles appears on the display.
2) Press SELECT
S
to return to the previous Menu.
SYSTE VERSION
Displays the version of the firmware loaded on the CPU board.
1) Press ENTER
A
– two options appear on the display:
Application release
Boot release
2) Use the UP
B
and DOWN
C
keys to select which of the two
firmware version items to be displayed.
3) Press ENTER
A
– the release appears on the display.
4) Press SELECT
S
to return to the previous Menu.
INFOR ATION ENU
Backlight
Display
contrast
Factory
Information
Partial LED
hours
Charge
Battery num.
Total LED
hours
Charge
Battery hours
Discharge
Battery hours
System
version
10
All manuals and user guides at all-guides.com

11
GLOW UP
LED TE PERATURE
Displays the LED working temperature.
1) Press ENTER
A
– two options appear on the display:
Temperature (real-time LED temperature)
ax Temperature (maximum temperature measured on LEDs)
2) Use the UP
B
and DOWN
C
keys to select which of the two
temperature items to be displayed.
3) Press ENTER
A
to display or SELECT
S
to return to the previous
menu.
To reset the “ ax Temperature” value, simultaneously press and hold
down the UP
B
and DOWN
C
keys for several seconds. When “Rst?”
(Reset) appears, confirm by pressing ENTER
A
.
BATTERY VOLTAGE
Displays the battery output voltage.
1) Press ENTER
A
– voltage appears in Vdc on the display.
2) Press SELECT
S
o return to the previous Menu.
BATTERY TE PERATURE
Displays the battery temperature.
1) Press ENTER
A
– temperature appears in °C on the display.
2) Press SELECT
S
to return to the previous Menu.
PRODUCT ID
Displays the ID address assigned to the GlowUP.
1) Press ENTER
A
– the address appears on the display.
2) Press SELECT
S
to return to the previous Menu.
CHANNEL ONITOR
Displays the DMX input level in bit for each GlowUP channel.
1) Press ENTER
A
– the first channel appears on the display.
2) Use the
B
and DOWN
C
keys to select the channel.
3) Press ENTER
A
to display the channel DMX level (value between 0
and 255).
4) Press SELECT
S
to return to the previous Menu.
SYSTE ERRORS
Used to display or reset the list of GlowUp errors found during start up.
1) Press ENTER
A
.
2) Use the
B
and DOWN
C
keys to select one of the following
options:
Error onitor: press ENTER
A
to display the error list.
Error Reset: press ENTER
A
to reset the error list displayed in the
ERROR MONITOR. A confirmation message appears on the display
(O ?). Press ENTER
A
again to reset the list.
3) Press SELECT
S
to return to the previous Menu.
CPU RESET
Used to reset the CPU. Settings will not be reset.
1) Press ENTER
A
– a confirmation message appears on the display
(O ?)
2) Press ENTER
A
to RESET or SELECT
S
to return to the previous
Menu.
Continued ➔
LED
temperature
Battery
voltage
Battery
temperature
Product ID
Channel
monitor
ADVANCED ENU
Advanced
CPU Reset
System
Errors
All manuals and user guides at all-guides.com
all-guides.com

12
GLOW UP
TEST
Used to test the correct operations of effects.
1) Press ENTER
A
.
2) Use the
B
and DOWN
C
keys to select the Test function.
3) Press ENTER
A
to confirm the select and start the TEST or SELECT
S
to keep current settings.
CHANGE ODEL
Use to change/select the model to be assigned to the projector.
1) Press ENTER
A
– current settings appear on the display.
2) Use the
B
and DOWN
C
keys to select one of the following models:
COLOR
TUNABLE WHITE
WHITE
3) Press ENTER
A
to confirm the selection (the display blinks for
several seconds) or SELECT
S
to keep the current settings and
return to the previous Menu.
FW UPLOADER
Used to transfer software from one projector to all other connected
projectors.
1) Press ENTER
A
use the UP() e DOWN() keys to select:
Cable upload: to start the firmware upload via DMX cable.
Radio upload: to start the firmware upload via wireless
2) Press ENTER
A
to transfer firmware or SELECT
S
to return to the
previous Menu.
BATTERY SELECT
Used to change/select the type of battery used on the projector.
1) Press ENTER
A
– current settings appear on the display.
2) Use the
B
and DOWN
C
keys to select one of the following
settings:
TYPE A Battery – standard battery
TYPE B Battery – optional battery
3) Press ENTER
A
to confirm the selection (the display blinks for
several seconds) or SELECT
S
to keep the current settings and
return to the previous Menu.
FW
Uploader
Battery
Select
Test
Change
Model
All manuals and user guides at all-guides.com

13
GLOW UP
anual zoom - Fig. 10
The GlowUP has a manual zoom located on the back of the projector head.
1
2
10
ANUAL ZOO
1
1/4 Turn
2
11
AINTENANCE
All manuals and user guides at all-guides.com

14
GLOW UP
3
4
6
5
1/4 Turn
2
1
12
BATTERY RE OVAL
This product contains lithium iron tetraphosphate rechargeable battery. To protect the environment, please discard the battery at the end
of its working life according to current law.
LiFePo
All manuals and user guides at all-guides.com

15
GLOW UP
Periodic cleaning - Fig. 13
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The fre-
quency with which the following operations are to be carried out depends on various factors such as wear and the work environment quality (air humi-
dity, dust, salinity, etc.). To remove dirt from external parts, use a soft cloth dampened with any liquid glass cleaning detergent.
It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following
operations:
• General cleaning of internal parts.
• General visual check of internal parts, cabling, mechanical parts, etc.
• Electrical, photometric and functional checks; eventual repairs.
13
Parts requiring frequent cleaning.
12
14 15
OPTIONAL ACCESSORIES
MAGNETIC HOLDER
255036/001 black
255036/002 white
PADLOC
Not commercialized from Clay Paky
All manuals and user guides at all-guides.com

16
GLOW UP
365,5
(14,37")
226
(8,90")
165
(6,49")
TECHNICAL DATA
THE PROJECTOR WILL NOT SWITCH ON
TROUBLE
THE PROJECTOR WILL NOT SWITCH ON
DEFECTIVE PROJECTION
REDUCED LUMINOSITY
POSSIBLE CAUSES CHECKS AND REMEDIES
No power supply.
LED burnt out or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Optic fault.
Dust or grease deposits.
Check the power supply voltage or battery charge.
Replace LED.
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
CAUSE AND SOLUTION OF PROBLE S
Source
4 10 W MC-E Cree leds
Led pilot power
40W
Optics
Optic zoom, manually adjustable, magnetic support
for any additional diffusers
LED color temperature
5700°C GlowUP C
6000°C GlowUP W
6200°C cool white GlowUp TW
2700°C warm white GlowUp TW
4200°C cool+warm white GlowUp TW
Head adjustment
+/-105°
Cooling
High efficiency external die-cast aluminium
Control
• Wireless DMX multimode: Master, Slave and
Reapeter
• Antenna built in the case IP65
• Master: can transmit other slaves the synchroni-
sed DMX scenes saved on it, both as macros
and as DMX recorder.
• Repeater: Receives the signal from the master
and re-transmits it to other Slaves hidden from
the master
• XLR 5-pole DMX-in DMX-out standard sockets
• Remote wireless board settings with PC
• Default macros, user programmable macros.
• DMX recorder to save scene sequences.
User interface
• LCD display 2 lines with 16 characters each,
backlit LED, white on black
• 4 membrane buttons
External power
full range 100-240V 50-60Hz, PowerCon connec-
tor, for both battery charge and normal operations
Absorbed power
50W max - 170 VA
Body
• Injection pressed ABS case (UV protected)
• Finish: Polished metallic – Painted White or
Black
• carrier handle
• 4 non-slip rubber feet
Fittings
2 fast-look holes for omega hook-up
Safety
safety chain hole and padlock hole
Weight
7.5 g
Protection rating
IP65
Valves
Compensation valve IP65
Battery
• Duration 10 hours full, white, 20 hours color fade
• 4-hour fast charge from flight case, 8 hours in
slow charge with PowerCon
• More than 2,000 charge/deplete cycles
• No memory effect
• No acid leaks
Working position
Works in any position
CE arking
• In conformity with European Union Low Voltage
Directive 2006/95/CE and Electromagnetic com-
patibility directive 2004/108/CE
All manuals and user guides at all-guides.com
all-guides.com

17
GLOW UP
GLOW UP C
CHANNEL FUNCTIONS
CHANNEL CHANNEL ODE
RED
GREEN
BLUE
WHITE
DIMMER
STOP / STROBE
MACRO COLOR
MACRO TIMING
MACRO FADING
1
2
3
4
5
6
7
8
9
GLOW UP TW
CHANNEL INDEPENDENT CONSTANT INTENSITY AX INTENSITY
CHANNEL ODE
COOL WHITE 6200°
WARM WHITE 2700°
STOP / STROBE
TUNABLE WHITE
DIMMER
STOP / STROBE
TUNABLE WHITE
DIMMER
STOP / STROBE
1
2
3
GLOW UP W
CHANNEL CHANNEL ODE
DIMMER
STOP / STROBE
1
2
All manuals and user guides at all-guides.com

18
GLOW UP
BIT % EFFECT
255 100
COLOUR INSERTED
0 0.0
COLOUR EXCLUDED
CHANNEL 1
RED
CHANNEL 2
GREEN
CHANNEL 3
BLUE
• COLOUR IXING - channel 1 - 2 - 3
Operation with option color mi ing: RGB
BIT %EFFECT
255 100
WHITE
0 0.0
BLACK
• WHITE - channel 4
• DI ER - channel 5
BIT % EFFECT
255 100 OPEN (LIGHT)
CLOSED (BLACK)0 0.0
• STOP / STROBE - channel 6
• ACRO COLOR - channel 7
BIT % EFFECT
248
240
232
224
220
216
212
208
204
200
196
192
188
184
180
176
172
168
164
160
156
152
148
144
140
136
132
128
124
120
116
112
108
104
100
96
92
88
84
80
76
72
68
64
60
56
52
48
44
40
36
32
28
24
20
0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
255
247
239
231
223
219
215
211
207
203
199
195
191
187
183
179
175
171
167
163
159
155
151
147
143
139
135
131
127
123
119
115
111
107
103
99
95
91
87
83
79
75
71
67
63
59
55
51
47
43
39
35
31
27
23
19
COLD TONE
WARM TONE
PASTEL TONE
SEQ1
SKELTON EXOTIC SANGRIA
FLESH PINK
CHERRY ROSE
MAYAN SUN
LIGHT SALMON
COOL BLUE
URBAN BLUE
ROSE INDIGO
ALICE BLUE
BRIGHT BLUE
MAUVE
ENGLISH ROSE
FIRE
SURPRISE PEACH
SCARLET
SURPRISE PINK
JUST BLUE
CHOCOLATE
DARK LAVENDER
APRICOT
PALE LAVENDER
DEEP GOLDEN AMBER
GOLDEN AMBER
MEDIUM BLUE
BRIGHT PINK
DARK BLUE
MED BLUE GREEN
BLUE 2
MAGENTA 2
DARK PINK
LIGHT ROSE
ORANGE 2
STRAW
YELLOW 2
WHITE 2500
WHITE 3200
WARM WHITE
COOL WHITE
FULL WHITE
SKY BLUE
AQUAMARINE
VIOLET
PINK
ORANGE
WHITE
MAGENTA
CYAN
YELLOW
BLUE
GREEN
RED
NONE
• ACRO TI ING - channel 8
BIT % EFFECT
255 100
0 0.0
• ACRO FADING - channel 9
BIT % EFFECT
255 100
0 0.0
GLOW UP C
All manuals and user guides at all-guides.com

19
GLOW UP
BIT % EFFECT
255 100 WHITE INSERTED
WHITE EXCLUDED0 0.0
•COOL WHITE - channel 1
• WAR WHITE - channel 2
BIT %EFFECT
255 100 WHITE INSERTED
WHITE EXCLUDED0 0.0
GLOW UP TW
• STOP / STROBE - channel 3
BIT % EFFECT
255 100 WARM WHITE
COOL WHITE0 0.0
•TUNABLE WHITE - channel 1
• WAR WHITE - channel 2
BIT % EFFECT
255 100 OPEN (LIGHT)
CLOSED (BLACK)
0 0.0
• STOP / STROBE - channel 3
INDEPENDENT
INDEPENDENT ODE
COOL WHITE 6200°
WARM WHITE 2700°
STOP / STROBE
CONSTANT INTENSITY
CONSTANT INTENSITY AX INTENSITY
AX INTENSITY
CONSTANT INTENSITY & AX INTENSITY ODE
TUNABLE WHITE
DIMMER
STOP / STROBE
TUNABLE WHITE
DIMMER
STOP / STROBE
100
6200°C 4200°C 2700°C
0
50
COOL WARM
COOL WARM
100
0
50
100
6200°C 4200°C 2700°C
0
50
100
0
50
All manuals and user guides at all-guides.com

CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. [phone] - Fax [phone] - www.claypaky.it
PRELIMINARY 04/12 Cod. 099114-EN
gfstudio.com
• DI ER - channel 1
BIT % EFFECT
255 100 OPEN (LIGHT)
CLOSED (BLACK)
0 0.0
• STOP / STROBE - channel 2
GLOW UP W
All manuals and user guides at all-guides.com