Clevertronics LED CIRCLITE Installation and operating instructions

1948345 V2.2 11 August 2020
Rated Emergency Lumen Output in accordance with AS2293.1, not applicable
for –TH (theatre) version (refer to spacing tables for installation positions):
Refer to the Technical Label for classification information.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As aresult, any Exit & Emergency Units, on thesecircuits, will havetheir batteries discharged
or “cycled”. The battery in this fitting has been selected to give excellent long-life performance in a
controlled AS2293 testing environment. Excessive battery cycling will reduce through-life performance and
may lead to premature battery failure. Battery warranty claims, as a result of such abuse, are specifically
EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz/
Victoria (Head Office & Manufacturing)
Website: www.clevertronics.com.au
Email: [e-mail]
Phone: [phone]
Fax: [phone]
New South Wales
Phone: [phone]
Fax: [phone]
Queensland
Phone: [phone]
Fax: [phone]
South Australia/Northern Territory
Phone: [phone]
Fax: [phone]
Western Australia
Phone: [phone]
Fax: [phone]
New Zealand
Phone: [phone]
Models:
FCLLED LED Circlite with Cool White LEDs
FCLLED-WW LED Circlite with Warm White LEDs
FCLLED-MS LED Circlite with Cool White LEDs and microwave movement sensor
FCLLED-WW-MS LED Circlite with Warm White LEDs and microwave movement sensor
ECLLED LED Circlite with Cool White LEDs and maintained emergency function
ECLLED-WW LED Circlite with Warm White LEDs and maintained emergency function
ECLLED-MS LED Circlite with Cool White LEDs maintained emergency and microwave movement sensor.
ECLLED-WW-MS LED Circlite with Warm White LEDs maintained emergency and microwave movement sensor.
Spare Parts:
1510160 –Battery, 6 x Sub C NiCad Battery SBS, 7.2V 1800mAh
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant Australian and International Standards.
LED CIRCLITE Luminaire
Installation & Maintenance Instruction Leaflet
Designed in Australia to comply with the requirements of
AS2293.3: 2005 and AS/NZS CISPR15: 2017

1948345 V2.2 11 August 2020
Installation:
A. Surface Mount
1. Disassemble the diffuser and LED panel.
2. Pull the power cord through the grommet.
3. Fix the base to the surface.
4. Connect the power cord.
5. Assemble the LED panel and diffuser.
B. Semi recessed Mount (special option)
1. Cut a 320mm hole into the mounting surface.
2. Disassemble the diffuser and LED panel.
3. Place the metal frame above the hole in the
mounting surface.
4. Pull the power cord through the grommet.
5. Insert the base into the mounting hole and
attach to the frame with 2 x 4mm screws.
6. Assemble the LED panel and diffuser.
Power Supply Connection, 240V, 50Hz: Connect power to the fitting as shown.
Testing:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least
24 hours. Conduct the following tests:
•For the first test, the emergency lamp must remain illuminated for at least 2 hours after
disconnection from the mains supply.
•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are
required to be recorded in a service logbook, which is to be kept on-site at all times. If the unitfails
to remain illuminated for the requisite time, remedial action must be taken to repair the situation
and once completed, the unit must pass a subsequent test. For more specific information, please
refer to the current edition of the AS 2293.2 Standard.
Trouble Shooting:
Below are a list of common problems and their possible causes.
Fault: The Red LED indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault: Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Battery is connected.
Red LED is on (battery charging).
Fault: Lamp illuminates in emergency mode, but only stays on for a short period.
Check: Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Battery Replacement
1. Disconnect power.
2. Remove the battery plug from the PCA
3. Remove the battery mounts
4. Remove the old battery
5. Fit the new battery and fix in position
6. Reconnect the battery to the PCA.
Metal Frame
Metal Ring
FCLLED-MS & ECLLED-MS (sensor)
FCLLED & ECLLED (no sensor)
Note: Link 1&2 for permanent on or use switch for on/off