Clevertronics L10 Weatherproof Jumbo LED Exit Installation and operating instructions

1947282
V1.2
4 October 2022
UK Instruction Sheet Template –V1.3 –Updated: 20/01/2022
Clevertest and Clevertest Plus
Refer to the supplementary operation guide supplied with the Product.
After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red flashing
for a period up to 2 minutes.
Zoneworks, HIVE and DATA Monitored Options
Fittings with part numbers -ZW, -HVG, -DATAare fitted with Zoneworks communicationsmodules (nodes). These
fittings are monitored using either Powerline Carrier Technology that utilize the power cable to provide data
communication, RF transceiver modules operating inthe ISM band or a dedicated data cable to/from data routers
installed on a dedicated data trunk connected to a central Server (can also be connected via
Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor, coordinate testing and collate test
data from eachfitting. Zoneworks Fittings can be commissioned by a single push of the test switch or by scanning
the supplied barcode. The LED Test Switch indicator provides a multifunction indication of the status of the fitting
during testing and normal operation:
Option
State
LED Operation
ZW, HVG, DATA
Commissioned
LED on Solid (Green)
ZW, DATA
Un-commissioned
Batt plugged-in: yellow 1s, green 1s
Batt unplugged: red 1s, off 1s
HVG
Un-commissioned
With network connectivity
Batt plugged-in: yellow 1s, green 1s
Batt unplugged: red 1s, off 1s
HVG
Un-commissioned
Without network connectivity
Batt plugged-in: yellow 250mS, green
250mS, yellow 250mS, green 250mS,
green 1s
Batt unplugged: red 250mS, off 250mS,
red 250mS,off 250mS, off 1s
ZW, DATA
Emergency Light Test In Progress
LED flashes at yellow 5s , 0ff 1s
HVG
Emergency Light Test In Progress
LED flashes at yellow 1s , 0ff 1s
In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to the
DATA network via a multi-drop bus (daisy chain connection). For further information of installation of a
Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA version)
DALI EM Option
Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection and
integration to 3rd Party Lighting Control Systems. Before installing the -DALI fitting please confirm that the
Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI fitting will be
addressed and configured into the control system by the Lighting Control System Commissioning Technicians
and not Clevertronics
State
LED Operation
Commissioned/ Un-commissioned
LED on Solid (Green)
Emergency Light Test in progress
LED flashes at 1s On (Yellow) & 1s Off
“IDENTIFY COMMAND”
Lamp and Status LED Flash for 30 seconds
A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network OR a 5/6way
“structured wiring system” lead and plug facilitating the power and DALI connection. DALI connections are
marked as Da Da.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries discharged or
“cycled”. The Li-ion battery in the Exit & Emergency Unit has been selected to give excellent long life
performance in a controlled IEC 60598-2-22 testing environment. Excessive battery cycling will reduce through-
life performance and may lead to premature battery failure. Battery warranty claims, as a result of such abuse,
are specifically EXCLUDED from Clevertronics warranty terms.
L10™ Weatherproof Jumbo LED Exit
One Box Solution
Installation & Maintenance Instruction Leaflet
Dimensions: 570mm x 117mm x 340mm Weight 5.6KG
Australia (Head Office)
Website: www.clevertronics.com.au
Email: [e-mail]
Phone: [phone]
Fax: [phone]
UK OFFICE
Website: www.clevertronics.co.uk
362 Stockley Close
West Drayton UB7 9BL
Phone: [phone]
NOTE: Standard product codes with this symbol are enabled
with Clevertest Plus capability. Please refer to the operation guide
supplied with the product for details.
IP65
Models:
LJWELED-50-xx-yy-uu-ww
Testing:
Options:
Manual Test
xx = Blank
Tamperproof
yy=TP
Zoneworks
xx = ZW
Uninterrupted Power Supply
ww=UPS
Z/W DATA
xx = DATA
Black Colour
uu=BLK
Zoneworks HIVE
xx = HVG
DALI Registered.
xx = DALI
Spare Parts:
1530231
Replacement Battery (L10)
8050640
Replacement Emergency LED Board
UKM01370170001
Replacement Emergency Driver
Important:
It is illegal for anyone, exceptfor a licensedelectrician to install or maintainthis product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant British Standards.

1947282
V1.2
4 October 2022
UK Instruction Sheet Template –V1.3 –Updated: 20/01/2022
Installation:
•Locate the installation position.
•Remove the front trim piece, by levering one of the corners up and pulling off. (Figure A)
•Remove the front Diffuser by undoing the 4 holding screws then lever it out. (Figure A)
•Remove Gear Tray by undoing the 3 retaining screws using a suitable screwdriver. (Figure B)
•Position the product in the wall or ceiling mount position & pre-drill mounting holes (Figure C).
•Wall Mount pull back the Seal Tab to expose mounting holes. Feed your screwdriver through front facing holes to
access fixing screws (Figure C).
•Mount product using suitable fixings (including consideration of maintaining the IP rating).
•Drill suitable entry points for supply cables either on the top, rear, or sides of the base using a suitable tool for
polycarbonate plastic. (Figure C)
•The product is designed to take a Maximum M25 Cable Gland/ conduit adaptor. A suitable round cable diameter
will need to be selected when Cable Gland used, consult Manufacturer datasheet.
•Seal Cable entry and Mounting holes appropriately to maintain the IP Rating stated on the Technical Label.
•Terminate the supply cables to the unswitched Live, Neutral & Earth terminals (in the case of the –DALI or –
DATA fittings terminate the cable to the polarity free terminals marked Da Da or DATA).
•Ensure the Battery is connected. Push the gear tray back into position, make sure that the clips on the back are
properly engaged, and secure in place using the three screws.
•Attach the diffuser panel by inserting the base into the channel on the body of the exit sign, taking care to verify
the seal is in place and the clips are properly engaged, and then fold the panel up to position the locking screws.
Tighten the diffuser screws and fit the front trim. (All screws need to be firm before the front trim can be fitted.)
•If the CTP self-test capabilities are activated, please affix the CTP status label to a visible surface and add the
letter “F” to the 3rd square in the Four Segment Marking on the product
Dimensions:
Note:
This luminaire (with reinforced insulation between control/LED terminal and AC supply) contains non-user
replaceable light source and battery - to be replaced (if required, refer installation instructions for battery
replacement) by Clevertronics service personnel/agents or a registered electrician.
Battery Replacement:
1. Prior to any work, isolate the power to the luminaire that requires battery replacement
2. Follow Installation section to remove Gear tray.
3. Disconnect Battery from EM Driver and remove Cable ties & Battery
4. Replace Battery, secure using cable ties and connect to Emergency Driver.
5. Follow Installation section to reassemble luminaire
Testing Procedure:
When the unit is connected to the un-switched active, it must be allowed to charge the battery for at least 24
hours. The emergency lamp only illuminates during a power fail. Conduct the following tests:
•The emergency lamp must illuminate for at least 180 min after disconnection from the mains. If the unit
fails to illuminate for the requisite time, remedial action must be taken to repair the situation and once
completed, the unit must pass a subsequent test.
•Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.
•Release the Test Button or Switch On Mains Supply, check that the emergency lamp is Off (Non-
maintained operation).
Trouble Shooting:
Below are a list of common problems and their possible causes.
Fault: The Green LED Test Switch indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault: Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency mode, but only stays on for a short period.
Check: Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
https://clevertronics.co.uk/product-warranty-statement/
Figure A
Figure B