Soundoff Signal mPower EMPR10004-WW User manual

1.800.338.7337 / www.soundo󰀨signal.com
1HIGH POWER SPOT 0321
HP LIGHT KIT
2.70.9
1.80.9
1.7 2.5
1.5
3.6
2.6
MAX
TORQUE: 12 IN-LBS.
29.6
1.2
42.9
1.69
39.2
1.54
24.2
0.95
23.2 0.91
91.6
3.61
66.3
2.61
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
MAX. TORQUE: 12 IN-LBS.
EMPR10004-WW (2x1) SHOWN
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s Manual for deployment zones.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local chassis ground (-) must be sized to supply at least 125%
of max. current and properly fused at power source.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Install protective grommets when routing wire through rewall or metal.
•Unit may become hot to touch during normal operation.
WARNING
MAX
TORQUE: 12 IN-LBS.
29.6mm
1.2”
42.9mm
1.69”
39.2mm
1.54”
24.2mm
0.95”
23.2mm
0.91”
91.6mm
3.61”
66.3mm
2.61”
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
A A
B B
C C
D D
E E
F F
G G
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWING NO:
SHEET
2 OF 2
DESCRIPTION:
REVISION:
MATERIAL:
High-power-assembly
MAX
TORQUE: 12 IN-LBS.
29.6
1.2
42.9
1.69
39.2
1.54
24.2
0.95
23.2 0.91
91.6
3.61
66.3
2.61
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
TIGHTEN 1/8 TURN PAST
FULL COMPRESSION OF
WASHER (FOR BOTH
LEFT AND RIGHT SIDES)
EMPR10004-WW (2x1) SHOWN
CONTAINS
QTY COMPONENT
2mpower® ORV 2x1 Light
2PMPR1BK001 - Bracket Kit
2PMPR1HN001 - Harness Kit
1Registration Card
1Installation Instruction sheet
1Product Warning Card
EMPR10004-WW INTRODUCTION:
PMPR1BK001*
BRACKET KIT CONTAINS
QTY COMPONENT
1Cradle Bracket
1U Bracket
1PMPR1HW001 - HPS Bracket Hardware
Kit
PMPR1HW002**
HARDWARE KIT
FOR DUAL STACKED MOUNT
CONTAINS
QTY COMPONENT
28-32, 1 1/2” FLNG BTN HD, SS Screw
2SPACER, 3/8 OD X 1/2” LONG
*included in purchase
**sold separately
SHOWN WITH DUAL STACKED
MOUNT APPLICATION
MAX. TORQUE: 12 IN-LBS.
EMPR10004-WW - 2x1
EMPR20013-W - 6x1
EMPR10037-WW - 2x1 Dual Stack Kit
!
CAUTION
Hot heat sink surface,
DO NOT touch while operating.
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into the
light beam at close range.
DO NOT USE POWER TOOLS TO
TIGHTEN
PMPR1HW001*
BRACKET KIT CONTAINS
QTY COMPONENT
15/16-18 Nylon Lock Nut
210-32, 3/8" PAN HD TORX, SS Screw
28-32, 3/8" FLNG BTN HD, SS Screw
15/16"-18 X 1" Long Carriage Bolt
2#10 Flat Washer, 7/16 OD SS
15/16 USS Flat Washer SS 3/4" OD
2#10 Split Lock Washer, SS
NOTE: MAKE SURE TO INSTALL LIGHT WITH
GORE PATCH FACING DOWN.
Protected by U.S. Patent 10,703,260
and Patents Pending
https://soundoffsignal.com/legal/patent-notication
NOTICE:
Installers and users must comply with all applicable federal, state and local laws
regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal
product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday,
8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to tech-
services@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION

1.800.338.7337 / www.soundo󰀨signal.com
2HIGH POWER SPOT 0820
HP LIGHT KIT
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
42.6
1.68
30.4 1.20
45.8
1.80
61.7
2.43
1.32
19.0
194.0
7.64
168.6
6.64
MAX. TORQUE: 12 IN-LBS.
CONTAINS
QTY COMPONENT
1mpower® ORV 6x1 Light
1PMPR2BK001 - Bracket Kit
1PMPR2HN002 - Harness Kit
1Registration Card
1Installation Instruction sheet
1Product Warning Card
EMPR20013-W INTRODUCTION:
EMPR20013-W (6x1) SHOWN
PMPR2BK001*
BRACKET KIT CONTAINS
QTY COMPONENT
1Cradle Bracket
1U Bracket
1PMPR1HW001 - HPS Bracket Hardware
Kit
PMPR2HN002*
HARNESS KIT CONTAINS
QTY COMPONENT
13-Wire Harness, TE Connector, HP SP
PMPR1HW002**
HARDWARE KIT
FOR DUAL STACKED MOUNT
CONTAINS
QTY COMPONENT
28-32, 1 1/2” FLNG BTN HD, SS Screw
2SPACER, 3/8 OD X 1/2” LONG
*included in purchase
**available for 6x1 light kit, sold separately
MAX
TORQUE: 12 IN-LBS.
29.6
1.2
42.9
1.69
39.2
1.54
24.2
0.95
23.2 0.91
91.6
3.61
66.3
2.61
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
TIGHTEN 1/8 TURN PAST
FULL COMPRESSION OF
WASHER (FOR BOTH
LEFT AND RIGHT SIDES)
MAX
TORQUE: 12 IN-LBS.
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
42.6mm
1.68”
30.4mm
1.20”
45.8mm
1.80”
61.7mm
2.43”
1mm.32
1”9.0
194.0mm
7.64”
168.6mm
6.64”
REVISION LOG
REV DESCRIPTION INITIALS ECN DATE
1 FOR INSTALLATION SHEET
03/16/2020
A A
B B
C C
D D
E E
F F
G G
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
CAD DIMENSIONS ARE BASIC
UNLESS OTHERWISE SPECIFIED
GD&T TO FOLLOW
ASME Y14.5M-2009
DRAWING NO:
B
PRIMARY DIMS: INCH
DUAL DIMS: [mm]
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
DO NOT SCALE
DRAWING
SIZE:
SHEET
1 OF 2
DESCRIPTION:
REVISION:
®
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL.
ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
THIRD ANGLE
PROJECTION
MATERIAL:
High-power-assembly
EMPR20013-W (6x1) SHOWN
DO NOT USE POWER
TOOLS TO TIGHTEN
!
CAUTION
Hot heat sink surface,
DO NOT touch while operating.
EMPR10004-WW - 2x1
EMPR20013-W - 6x1
PMPR1HW001*
BRACKET KIT CONTAINS
QTY COMPONENT
15/16-18 Nylon Lock Nut
210-32, 3/8" PAN HD TORX, SS Screw
28-32, 3/8" FLNG BTN HD, SS Screw
15/16"-18 X 1" Long Carriage Bolt
2#10 Flat Washer, 7/16 OD SS
15/16 USS Flat Washer SS 3/4" OD
2#10 Split Lock Washer, SS

3HIGH POWER SPOT 0320
ELECTRICAL CONNECTIONS:
See diagram to the left for required electrical connections. Connect the RED wire to +10-32 Vdc through a customer supplied fuse (see Technical
Speciations table for fuse rating) and switch. Connect the BLACK wire to a reliable ground. Connect GREEN wire to ground for low power dim
operation. Extend 2ft. wire harness using recommended wire gauge for a single light.
MPOWER®ORV 2X1 TECHNICAL SPECIFICATIONS
Overall Dimensions: 1.2”H x 3.61”W x 3.23”D
Dual Stack Dimensions: 2.7”H x 3.61”W x 3.23”D
Input Voltage Range: 10-32Vdc
Current Draw: 1.25 Amps @ 12.8 Vdc, 0.63 Amps @ 25.6 Vdc
Wattage: 16 Watts
Reverse Polarity, Load Dump, Over Voltage: Protected
Operating Temperature: -40º to +65º C
Optical Distribution: Spot - Flood
Number of LEDs: 2
Color Temperature: 5700K
Raw Lumens: 1400
Fuse Rating Required: 5A
Recommended Wire Gauge & Max Length:
AWG LENGTH (ft.)
22 10
20 20
18 30
RED
BLACK
FUSE
+10-32Vdc
(-) GROUND
MAX
TORQUE: 12 IN-LBS.
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
42.6mm
1.68”
30.4mm
1.20”
45.8mm
1.80”
61.7mm
2.43”
1mm.32
1”9.0
194.0mm
7.64”
168.6mm
6.64”
REVISION LOG
REV DESCRIPTION INITIALS ECN DATE
1 FOR INSTALLATION SHEET
03/16/2020
A A
B B
C C
D D
E E
F F
G G
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
CAD DIMENSIONS ARE BASIC
UNLESS OTHERWISE SPECIFIED
GD&T TO FOLLOW
ASME Y14.5M-2009
DRAWING NO:
B
PRIMARY DIMS: INCH
DUAL DIMS: [mm]
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
DO NOT SCALE
DRAWING
SIZE:
SHEET
1 OF 2
DESCRIPTION:
REVISION:
®
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL.
ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
THIRD ANGLE
PROJECTION
MATERIAL:
High-power-assembly
GREEN
(-) GROUND
MPOWER®ORV 6x1 TECHNICAL SPECIFICATIONS
Overall Dimensions: 1.2”H x 7.64”W x 3.48”D
Dual Stack Dimensions: 2.7”H x 7.64”W x 3.48”D
Input Voltage Range: 10-32Vdc
Current Draw: 4 Amps @ 12.8 Vdc, 2 Amps @ 25.6 Vdc
Wattage: 51 Watts
Reverse Polarity, Load Dump, Over Voltage: Protected
Operating Temperature: -40º to +65º C
Optical Distribution: Spot - Flood
Number of LEDs: 6
Color Temperature: 5700K
Raw Lumens: 4300
Fuse Rating Required: 7.5A
Recommended Wire Gauge & Max Length:
AWG LENGTH (ft.)
18 14
16 22
14 35
RED
BLACK
FUSE
+10-32Vdc
(-) GROUND
MAX
TORQUE: 12 IN-LBS.
29.6mm
1.2”
42.9mm
1.69”
39.2mm
1.54”
24.2mm
0.95”
23.2mm
0.91”
91.6mm
3.61”
66.3mm
2.61”
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
TIGHTEN
1/8 TURN PAST
FULL COMPRESSION
OF WASHER
A A
B B
C C
D D
E E
F F
G G
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWING NO:
SHEET
2 OF 2
DESCRIPTION:
REVISION:
MATERIAL:
High-power-assembly
GREEN
(-) GROUND
EMPR10004-WW (2x1) SHOWN
(NOT SHOWN WITH DUAL STACK)
EMPR20013-W (6x1) SHOWN
(NOT SHOWN WITH DUAL STACK)
Lights are chassis-grounded. If you need to ground-switch the light, you must isolate the
lights metal backing, heatsink, studs and/or screws from the body of the vehicle or use a relay.

1.800.338.7337 / www.soundo󰀨signal.com
4HIGH POWER SPOT 0321
HP LIGHT KIT
RETENTION CLIP INSTRUCTIONS*
1. Plug harness into light housing, aligning tab to window, as
shown in Fig 1.
2. Install the retainer clip over harness/light interface,
inserting retainer into window, as shown in Fig. 2.
3. Press retainer clip's locking arm to snap closed.
*In the event the harness needs to be disengaged from the
light, these instructions can be used to reattach and apply
the retention clip.
FIG. 1
WINDOW
TAB
FIG. 3 FIG. 4
RETAINER
FIG. 2
LOCKING ARM
FULLY SEATED RETENTION CLIP
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION