Clevertronics LP CWSQLED Series User manual

1949210
V1.3
17 October 2018
Clevertest and Clevertest Plus
Refer to the supplementary operation guide supplied with the Product.
After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red
flashing for a period up to 2 minutes.
The diffuser will require removal to gain access to the Test/Status Switch and LED.
Maintained fittings (CWSQLEDM-yy-zz) cannot be scanned with a camera using the CleverSparky App
as the maintained light source interferes with the camera scanning function. To register the fitting
manually enter the serial number from the QR code and visually read the test result and enter manually
into CleverSparky.
Zoneworks and DATA Monitored Options
Argonauts Square with part numbers CWSQLEDx-ZW, CWSQLEDx-DATA are fitted with Zoneworks
communicationsmodules (nodes). These fittings are monitored using either Powerline Carrier Technology
that utilises the power cable to provide data communication or a dedicated data cable to/from data routers
installed on a dedicated data trunk connected to a central Server (can also be connected via
Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor, coordinate testing and
collate test data from each fitting. Zoneworks fittings can be commissioned by a single push of the test
switch or scanning of the supplied barcode. The LED Test Switch indicator provides a multifunction
indication of the status of the fitting during testing and normal operation:
State
LED Operation
Commissioned
LED on Solid (Green)
Un-commissioned
LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)
Emergency Light Test In Progress
LED flashes at 3s On (Yellow) & 0.5s Off
In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to
the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of
a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA
version)
DALI EM Option
Argonauts Square with part numbers CWSQLEDx-DALI are fitted with DALI modules (nodes)that facilitate
connection and integration to 3rd Party Lighting Control Systems. Before installing the CWSQLEDx-DALI
please confirm that the Lighting Control System has the capability to monitor DALI Emergency Luminaires.
The CWSQLEDx-DALI will be addressed and configured into the control system by the Lighting Control
System Commissioning Technicians and not Clevertronics.
State
LED Operation
Commissioned/ Un-commissioned
LED on Solid (Green)
Emergency Light Test in progress
LED flashes at 1s On (Yellow) & 1s Off
“IDENTIFY COMMAND”
Fitting goes into emergency mode for 10 seconds
A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI
connections are marked as Da Da.
Argonaut Square LED Sensor Light
Installation & Maintenance Instruction Leaflet
Victoria (Head Office & Manufacturing)
195 Chesterville Rd
Moorabbin VIC 3189
Phone: [phone]
Fax: [phone]
New South Wales
Phone: [phone]
Fax: [phone]
Queensland
Phone: [phone]
Fax: [phone]
South Australia/Northern Territory
Phone: [phone]
Fax: [phone]
Western Australia
Phone: [phone]
Fax: [phone]
New Zealand
Phone: [phone]
Designed in Australia to comply with the requirements of
AS2293.3: 2005 and AS/NZS CISPR15: 2011
NOTE: Standard product codes with this symbol are
enabled with Clevertest Plus capability. Please refer to the
operation guide supplied with the product for details.
Models:
CWSQLEDx-yy-zz-vv
Testing:
Options:
Manual Test
zz = Blank
Non-Maintained
x = N
Zoneworks
zz = ZW
Maintained
x = M
Z/W DATA
zz = DATA
Microwave Sensor Hi/Lo Control
yy = MS-HL
DALI Comp.
zz = DALI
Microwave Sensor Control
yy = MS
Clevertest
zz = CT
Black Body
vv = BLK
(NOTE: -CTProducts supplied with the Clevertest Plus Symbol are activated with Clevertest
PLUS capability. Please refer to the operation guide supplied with the product for details).
Spare Parts:
1550290
BATT: LP 6.4V 3.2Ah.200mm lead.Stick.Brkt
1190320
Sensor: M/Wave Motion, SK-503L DC
(for -MS-HL)
1330120
LED Driver –GDY250, 26W 42VDC 610mA
8002840
PCA: SQ LED Array, 215mm, 400K, 3020 LED
CCPLED-38V120C-CKIT
LED Power Pack, 38V 120mA, LP
1190325
SENSOR:M/Wave Motion, SK-601 On/Off
(for -MS)
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant Australian and International Standards.

1949210
V1.3
17 October 2018
Installation:
The LP Argonaut Square (CWSQLEDx) can be installed either Ceiling or Wall Mounted.
•Remove the four (4) screws diffuser to the base.
•Remove the four (4) screws holding the gear tray to the base.
•Determine the cable access point. There are 2 locations on opposite sides of the fitting for cable
gland/conduit entry. Entry can also be from the back of the base. Drill out the desired cable entry
point.
•Drill out 4 of the mounting points in the base (see image below).
•Using the base as a guide, mark the 4 holes for mounting and one for mains access if using back
cable entry.
•Mount the base using appropriate fixings and seal these fixings with silicone (fill any additional entry
points with silicone also)
•Route the power inside the base.
•Connect the 240VAC (A,E,N,SA) supply to the terminal block of the gear tray.
•Install the gear tray to the base.
•Apply power to the fitting and test per the instructions.
•If the CTP capabilities are activated, please affix the CTP status Label to a visible surface.
Networking:
When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the
relevant Smart Node PCA.
Dimensions:
Testing:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24
hours. Conduct the following tests:
•For the first test, the emergency lamp must remain illuminated for at least 2 hours after
disconnection from the mains supply.
•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are
required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails
to remain illuminated for the requisite time, remedial action must be taken to repair the situation
and once completed, the unit must pass a subsequent test. For more specific information, please
refer to the current edition of the AS 2293.3 Standard.
Maintenance:
Lamp Replacement:
•Use only the lamp(s) recommended on the
label inside the Argonaut.
•To replace the lamp bar, remove the self-
tapping screws, disconnect the signal cable
and install the new lamp bar.
Battery Replacement:
•Use only the battery recommended on the
label inside the Argonaut and on this
instruction.
•Remove the fasteners holding the battery,
un-plug the lead from the PCB and remove
the old battery.
•Attach the new battery, route the DC cable
to the PCB and plug the new battery.
Trouble Shooting:
Below are a list of common problems and their
possible causes.
Fault: The Green LED Test Switch
indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault: Lamp does not illuminate in
emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency
mode, but only stays on for a short
period.
Check: Battery has been allowed to charge for
at least 24 hours.
Battery for damage.
Rated Emergency Lumen Output in accordance with AS2293.1 (refer
to spacing tables for installation positions):
C0=D50 C90=D50
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life
performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-
life performance and may lead to premature battery failure. Battery warranty claims, as a result of such
abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz/
Mounting Holes
Cable Entry