Coleman 2000015507 Manual

STITCH LINE
SHELTER SETUP INSTRUCTIONS
Before you begin
• Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp objects, to install your shelter.
WARNING: Keep clear of overhead power lines.
• Do not set up your shelter under trees because of potential lightning strikes or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage or personal injury.
• For best results in windy conditions, position narrow end of shelter into the wind.
• Do not drop shelter.
• Do not bounce shelter bag on its end to remove shelter, as these actions may damage the frame.
• THIS RECREATIONAL PRODUCT REQUIRES A MINIMUM OF TWO PEOPLE TO ASSEMBLE.
• Under no circumstances should this product be used to cover automobiles, marine products or similar items.
• This shelter is not designed for use as a permanent structure.
CAUTION: Avoid pinch points when opening and closing the shelter frame.
(continued on other side)
Extend the Shelter Frame
Set up the Shelter
• With two persons standing at diagonal corners of the
structure, grab the leg, and pull out to unfold frame. (Fig. 1)
NOTE: Do not unfold frame completely. This will allow
easier fit for draping shelter top over frame.
• Pull up sliding bracket located on upper portion of leg to
extend the awning pole until push button snaps into place.
This will ensure awning pole is fully extended. (Fig. 2)
• Attach vent supports to vent with hook and loop
fasteners. (Fig. 3A)
• Drape shelter top over frame and insert awning poles to
pole pockets at corners of the awning.
• Insert horizontal awning pole in pole sleeve at edge of awning,
assemble the horizontal awning pole with awning pole
(Fig. 3B), then insert pole ends into pole pockets. (Fig. 3C)
• Attach hook and loop fasteners, located on corners of
shelter top, to four corners at frame posts. (Fig. 3 & 3D)
• Pull up sliding bracket located on upper portion of leg until push
button snaps into place. (Fig. 4). This will ensure top of frame is
fully extended.
• Secure shelter top to frame with hook & loop fasteners provided.
(Fig. 5 & 6)
1
2
4
HANDY TIP: To fully engage the
push button, grip the top and
bottom frame members and
squeeze as shown in Fig. 4A. Be
careful to avoid pinch points.
Stake the Shelter
• Secure shelter by driving stakes through the holes in the
base of each frame post. (Fig. 9)
Adjust the Height
• Adjust desired height until push button locks into place,
making sure all four posts are level. (Fig. 7 & 8)
3
Push
Button
Upper
Portion
of Leg
Push
Button
Push Button
Fig. 3A
Fig. 3D
Fig. 3C
Fig. 3B
Fig. 3
Vent
Support
MODEL 2000015507
Fig. 1 Fig. 2
Fig. 9
Fig. 8
Fig. 7
Fig. 6
Fig. 4A
Fig. 5
Fig. 4
Awning Pole
Sliding
Bracket
Horizontal
Awning
Pole

STITCH LINE
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM
THIS TENT FABRIC.
Things You Should Know:
• Under certain conditions (cold weather, high humidity,
etc.) condensation will form on the inside of your shelter.
Condensation is caused by water vapor from your breath,
perspiration, or any wet clothing inside the shelter. It is NOT
LEAKAGE through the shelter fabric.
• Tree limbs, tree sap, bird droppings, or moisture steadily dripping
off tree limbs can cause damage to the shelter fabric and its
coating resulting in leaks or loss of flame-resistant properties.
•Never store shelter, even for a short period of time, without drying
it thoroughly and brushing off caked dirt. Do not pack stakes
inside your shelter. Use a separate storage bag.
• Stakes should be removed by pulling on the stake itself. NEVER
PULL ON THE SHELTER TO REMOVE STAKES AS THIS COULD
RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.
• Do not leave your shelter set-up for weeks at a time. Be aware
that exposure to ultraviolet rays from the sun can seriously
damage material and/or cause it to become discolored.
• This product is not intended to be used during heavy rain, wind,
hail, snow or other inclement weather. Excess water build-up
can cause the frame system to become unstable, and possibly
collapse, causing injury.
• The shelter top should be carefully removed during windy
conditions to avoid damage to product or personal injury.
• DO NOT use gas or flame sources under or near this product.
Secure the Guylines
• Attach and stake out guylines. (Fig. 10)
5
1. All stakes must be placed in the storage bag to prevent damage to the fabric items placed in the carry case.
2. Make sure all components are clean and dry before placing in carry case.
3. Store in a clean, dry area.
7
To Store
Disassembly
• Remove horizontal awning pole, guylines, and stakes.
• Lower the awning by sliding brackets downward.
• Lower the frame one post at a time by pressing the push
button locks located on lower portion of posts. (Fig. 13)
• Press the push buttons found at upper corners of the
frame (Fig. 14) and partially fold the frame. This will allow
easier removal of the shelter top from the frame.
• Remove the shelter top from frame and fold for storage.
• Collapse shelter frame and store in carry bag.
6
Coleman Brands Pty. Ltd.
Unit 5-6, 13 Lord Street,
Botany NSW 2019
Australia
Telephone: [phone]
Email: [email protected]
www.colemanaustralia.com.au
© 2017 The Coleman Company, Inc. All rights reserved.
Coleman®, , and are registered trademarks of
The Coleman Company, Inc.
Guyline
Guyline
Stake Fig. 10
4010025628 (ECN20060939-02)
Push
Button
Push
Button
Fig. 13 Fig. 14