College Park Odyssey K3 Owner's manual

800.728.7950 |586.294.7950 |college-park.com
ADDITIONAL CONSIDERATIONS
Have the user practice standing up from a seated position in order to acclimate to the
motion of the ankle. Use caution when driving. Make sure the user is comfortable with the
motion of the ankle if using the OdysseyK3 as their driving foot.
WARNING
▪Do not expose this product to corrosive materials, salt water or pH extremes.
▪Contaminants such as dirt and the use of lubricants or powder may eect the function of
the CPI Sock and lead to noise.
▪Failure to follow these technical instructions or use of this product outside the scope of
its Limited Warranty may result in injury to the patient or damage to the product.
WARRANTY INSPECTION /
MAINTENANCE INFORMATION
College Park recommends that you schedule your patients for check-ups according to the
warranty inspection schedule below.
High patient weight and/or impact level may require more frequent inspections. We
recommend you visually inspect the following applicable parts for excessive wear and
fatigue at each warranty inspection.
▪Hydraulic Assembly
▪Composites and Adapters
▪CPI Sock
▪Foot Shell
▪Wedge
WARRANTY INSPECTION SCHEDULE FOR ODYSSEYK3 : 6 MONTHS, THEN ANNUALLY.
TECHNICAL ASSISTANCE /
EMERGENCY SERVICE 24-7-365
College Park’s regular oce hours are Monday through Friday, 8:30 am – 5:30 pm (EST). After
hours, an emergency Technical Service number is available to contact a College Park representative.
EMERGO EUROPE
Prinsessegracht 20, 2514 AP
The Hague, Netherlands
COLLEGE PARK
INDUSTRIES, INC
27955 College Park Dr.
Warren, MI 48088 USA
Australian Sponsor
EMERGO AUSTRALIA
Level 20, Tower II
Darling Park
201 Sussex Street
Sydney, NSW 2000
Australia
522 INS OK3 TIS 171121
MADE IN THE USA
©2018 College Park Industries, Inc. All rights reserved. College Park,
Odysseyk3, and Gait Matching are registered trademarks.
technical
instructions
smooth curves ahead

Technical Instructions | OdysseyK3 Technical Instructions | OdysseyK3
DESIRED RESULT VALVE ADJUSTMENT COMPONENT CHANGE
Firmer Planterflexion Turn P-valve clockwise (more resistance) Install Rounded Heel Wedge
Softer Planterflexion Turn P-valve counterclockwise (less resistance) Remove Rounded Heel Wedge
Firmer Dorsiflexion Turn D-valve clockwise (more resistance) NONE
Softer Dorsiflexion Turn D-valve counterclockwise (less resistance) NONE
PROTECTIVE COVER ON DOME
Remove the protective cover on dome after alignment is completed and
before patient leaves clinic.
BENCH ALIGNMENT
The weight line should divide the foot at 1/3 heel lever to 2/3
toe lever. It will fall just anterior of the pyramid.
HYDRAULIC RANGE
The OdysseyK3 foot has 12º of hydraulic motion. The foot is designed to provide 3º hydraulic
dorsiflexion from the neutral standing position.
The foot was developed utilizing a dynamic carbon fiber base.
As a result, a typical user will experience an additional range of
dynamic motion
during ambulation.
Note: Excessive angular adjustment will aect the hydraulic
range of the foot. After making an alignment change, ensure
that the user retains 3º of hydraulic dorsiflexion.
PACKAGE CONTENTS
(1) OdysseyK3 Foot
(1) Foot Shell
(1) CPI Sock
(1) 3mm Hex Key
(1) OdysseyK3 Wedge Kit
TOOLS RECOMMENDED
4mm Hex Key
FootHorn
MOUNTING
Use only high quality endoskeletal components.
ASSEMBLY AND DISASSEMBLY (for sock replacement)
Use the FootHorn to don and do the foot shell. Remove the CPI Sock and replace as
needed. Any further disassembly or modification of components will void the warranty.
1.0 cm
Hydraulic Range
9° 3°
1⁄3 2⁄3
1.0 cm
STATIC ALIGNMENT
Using a 3mm hex key for adjustment, the hydraulic valves should be set at minimum
resistance. Have the user stand comfortably and evaluate the heel-toe balance of
the foot.
They will sense the hydraulic movement of the ankle but should not feel like they are
falling forward or backward. Use alignment to position the foot at the point where they
feel the most balanced.
SYMPTOM ALIGNMENT CHANGE
Falling Backward Shift foot posterior relative to the socket
Falling Forward Shift foot anterior relative to the socket
DYNAMIC ALIGNMENT
Have the user begin by walking on level ground, to evaluate the heel-toe resistance and gait
timing. Using a 3mm hex key, adjust for planterflexion resistance first, then dorsiflexion.
Finalize dynamic alignment by observing the user walking on an inclining-declining surface
(ramp). Make further adjustments to the resistance valves as necessary.
i
n
c
r
e
a
s
e
d
e
c
r
e
a
s
e
i
n
c
r
e
a
s
e
d
e
c
r
e
a
s
e
Posterior
Anterior
Planterflexion resistance aects
the user’s gait from Heel Strike to
Foot Flat.
Dorsiflexion resistance aects the
user’s gait through Midstance, as
the body travels over the foot.