Colortrac SmartLF SC25m User manual

SCIM-002
Colortrac Ltd
Page 1 of 7
Issue 2
SC Instruction Manual
Date: 12/02/14
This is a confidential controlled document and is the property of Colortrac Ltd.
It is not to be copied or reproduced in part or whole.
C
Co ol lo or rt tr ra ac c S SC C S Sc ca an nn ne er rs s
S
Se en ns so or r G Gl la as ss s

SC Scanners Scanner Service Manual
Page 2 of 7
SC Scanners
SC25m, SC25c & SC25e
SC36m, SC36c & SC36e
SC42m, SC42c & SC42e
Instruction Manual
Issue 2
©Colortrac Ltd 2014
The product and the contents of this publication may be changed without prior notification.
Colortrac Ltd makes every effort to ensure this publication is free from error. Misprints, errors
or quality observations should be reported to Technical Support, Colortrac Ltd.
Colortrac Ltd shall not be liable for any damages, errors, issues or events that result from the
use of the equipment or this manual.
No part of this product or publication may be reproduced,
copied or transmitted in any form or by any means without
permission from:
Colortrac Ltd.
Units 3 –5 Brunel Court.
Burrel Road.
St Ives,
Huntingdon,
Cambridgeshire,
PE27 3LW.
United Kingdom.
Tel: [phone]
Fax: [phone]
www.colortrac.com

SC Scanners Scanner Service Manual
Page 3 of 7
1.1 SingleSensor Glass Sub-Assy
1.1.1 Safety Precautions
Ensure that the power and USB cables are completely disconnected from the scanner unit.
Ensure the scanner is positioned on a stable maintenance platform.
1.1.2 Tools
Medium Flat Screwdriver
Soft Cloth
1.1.3 Associated Part Numbers
10H014 : SingleSensor Glass Sub-Assy
1.1.4 Procedure
1. To Remove, Open the Error!
Reference source not
found. and using a Medium
Flat Screwdriver and a clean
cloth, insert the screwdriver
into the recess at the left end.
2. Gentle lever back the
screwdriver to prise the
SingleSensor Glass Sub-
Assy away from the Error!
Reference source not
found..

SC Scanners Scanner Service Manual
Page 4 of 7
3. Continue to gently pull the
whole SingleSensor Glass
Sub-Assy away from the
Error! Reference source
not found..
4. Remove the SingleSensor
Glass Sub-Assy
5. When refitting the
SingleSensor Glass Sub-
Assy, make sure the right
end is against the End Plate.
6. Position the SingleSensor
Glass Sub-Assy over the
Error! Reference source
not found. and make sure it
is central all the way along.
NOTE: Before fitting the SingleSensor Glass
Sub-Assy, clean both sides with a lint free
cloth to remove any dust, dirt or fingerprints.

SC Scanners Scanner Service Manual
Page 5 of 7
7. Press firmly all along the
SingleSensor Glass Sub-
Assy until all the latches are
locked in place.
8. Close the Error! Reference
source not found..
9. Reconnect the Power and USB cables to the Scanner and power up the scanner and
Utilities Program.
10. Run the
1.2 Calibration
11. , see below.
12. Re-cycle the scanner and software.

SC Scanners Scanner Service Manual
Page 6 of 7
1.3 Calibration
1.3.1 Associated Part Numbers
10H028 :
1.4 Calibration
and Error! Reference source not found. Target
1. Open the Error! Reference
source not found. and
clean the SingleSensor
Glass Sub-Assy with a soft
cloth. Close the Lid
Assembley.
2. Insert the Calibration Target
so that the black part
section is inserted first, face
up.
NOTE: It is necessary to remove the
Magnetic Paper Guide so the target can fit
centrally in scanner.
3. Double click the SmartLF
SC Utilities icon.
4. On the front page, click the
‘Calibrate’ button.

SC Scanners Scanner Service Manual
Page 7 of 7
5. Click ‘OK’ to except the
message.
6. After approx. 4 minutes, the
‘Calibration’ (or
Normalisation) is complete.
During calibration , the
target will move through the
scanner in stages several
times.