Come.up Winch DV-3500i User manual

Utility Duty Winch
Model: DV-3500i
PN: 641101 12VDC 641105 12VDC 641371 24VDC
641233 24VDC 641236 12VDC
Introduction
 Feature
Line pull: 1,588 kg / 3,500 lb wire rope first layer
Wire rope: 5.5 mm x 15.2 m (7/32" x 50') galvanized aircraft A7 × 19
Brake: Mechanical and dynamic brakes hold full load
Clutch: Raise the clutch level for rapid wire rope payout
Control: Handheld pendant switch powers the winch
 Unpacking
．Integrated solenoid kit…………………………………………… 1 pc
．Remote control…………………………………………………… 1 pc
．Wire rope with hook……………………………………………… 1 pc
．Roller fairlead…………………………………………………….. 1 pc
．1.5 m battery leads………………………………………………… 1 pc
．Circuit breaker……………………………………………………… 1 pc
 Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
 Information requesting or parts ordering
Please specify the followings information:
．Winch PN ．Part descri
p
tion
．Serial number ．Re
p
lacement
p
art number
．Quantit
y
for each par
t
Installation
Before using the winch, make sure all electrical
components have no corrosion or damaged; the
environment should be clear and dry.
The voltage drop must not exceed 10% of the
nominal voltage of 12V or 24V under normal
operation condition.
 Winch and roller fairlead mounting
 Use the mounting hardware supplied to mount the winch on a flat
surface.
 The motor, drum and gear housing must be properly aligned.
 Wiring Diagram
 Attach the ground lead firmly to the negative (–) battery terminal and
power lead to the positive (+) battery terminal. The voltage drop for the
winch motor must not exceed 10% of the nominal voltage of 12/24V DC.
 Attach the red lead, positive (+), tightly to the circuit breaker marked AUX,
meanwhile, connect the copper plate to the other end of the circuit
breaker marked BAT.
 Connect the copper plate to the connector of the battery.
 Nut fastening for motor & solenoid
1.Holding the lower nut on the stub and fastening the upper nut clockwise.
2.The torque setting for motor nut M6 is 5.7 N-m / 50 lb-in and solenoid nut
M8 is 14 N-m / 124 lb-in.

Warning
 The winch is not intended to be used in any manner for the movement or
lifting of personnel.
 The pulling capacity shown is based on the wire rope first layer on the
drum.
 The rope winding on the drum shall remain 5 wraps from the drum.
Parts List
Item No. Description Part No. Qty
1 Rear cover 880136 1
2 Remote socket kit 880137 1
3 Motor kit, 12V 880296 1
Motor kit, 24V 880297
4 Brake kit 880280 1
5 Gear box kit 880281 1
6 Ring gear 880141 1
7 1st stage carrier 880283 1
8 2nd stage carrier 880284 1
9 3rd stage carrier 880285 1
10 Drum kit 880286 1
11 Base plate kit 881284 1
12 Clutch kit 880287 1
13 Wire rope w/hook 880298 1
14 Roller fairlead 880289 1
15 Mounting hardware 880290 1
16 Solenoid pack, 12V 880291 1
Solenoid pack , 24V 881290
17 Circuit breaker kit, 12V 880299 1
Circuit breaker kit, 24V 880300
18 Remote control 880295 1
19 Handsaver strap 880026 1
Winch Assembly
2022/03/29 Ver:10