Come.up Winch Seal Gen2 9.5rsi User manual

Self-Recovery Winch
Model: Seal Gen2 9.5rsi
PN: 295860 12V 295862 12V DC
295863 12V DC
Introduction
 Feature
Line pull: 4,309 kg / 9,500 lb synthetic rope first layer
Synthetic rope: 10mm × 30.5 m (3/8"×100′) synthetic rope
Brake: Patented cone brake holds full load
Clutch: Turn the T-handle for rapid rope payout
Control: Both handheld pendant switch and built-in digital
two ways wireless transmitter power the winch
 Unpacking
．Winch assembly……………………………………………………... 1 pc
．Control box……………………..………………….………………... 1 pc
．Remote control………………………………………………………. 1 pc
．Synthetic rope with sling hook……………………………………. 1 pc
．Hawse fairlead………………………..………………………………1 pc
．1.8 m (6′) 2 gauge battery lead………………………..……………
1 pc
．Wireless transmitter………………………………………………… 1 pc
 Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
Installation
Before using the winch, make sure all electrical components have no
corrosion or damaged; the environment should be clear and dry.
 Winch and hawse fairlead mountings
‧It is very important that the winch will be mounted on
a flat and hard surface of mounting channel in
order to make sure the motor, drum and gearbox
housing are aligned correctly.
‧
Hawse fairlead does not mount to the winch directly.
‧The synthetic rope shall be wound in an under-wound orientation only.
‧Four (4) M10 x 1.50 pitch 10.9 grade with 63.8 N-m torque settings
(maximum) high tensile steel bolts must be used in order to sustain the
loads imposed on the winch mounting.
‧Two (2) M10 x 1.50 pitch stainless steel bolts must be used for fastening the
hawse fairlead into the mounting channel.
 Wiring Diagram
•Connect thermal sensor harness plug, control ground, and cable A/F1/F2 to
the motor.
•Attach the ground lead firmly to the negative (–) battery terminal and power
lead to the positive (+) battery terminal. The voltage drop for the winch
motor must not exceed 10% of the nominal voltage of 12V DC.
 Nut fastening for motor & contactor
1. Holding the lower nut on the stub and fastening the upper nut clockwise.
2. The torque setting for nut is 14 N-m/124 lb-in.
Warning
‧The winch is not intended to be used in any manner for the movement or lifting
of personnel.

‧The rated line pull shown is based on the first layer of rope on the drum.
‧The rope winding on the drum shall remain 10 wraps from the drum to support
the rated load.
‧
Manufacturer is not responsible for the results of misuse, misapplication, faulty
installation or abuse of synthetic rope in any way.
Parts List
Item No. Description Part No. Qty
1 Waterproof motor w/housing 12V 883544 1
2 Tie bar kit 883132 2
3 Motor coupling 880005 1
4 Drum bushing 880006 2
5 Drum kit 881521 1
6 Gearbox support rack 882523 1
7 Grounding lead 880009 1
8 Synthetic rope 883248 1
9 1st shaft 880011 1
10 3rd ring gear kit 880114 1
11 3rd stage carrier 880115 1
12 2nd stage carrier 880116 1
13 1st stage carrier 880117 1
14 1st & 2nd ring gear 880118 1
15 1st pinion 880119 1
16 Clutch kit 881564 1
17 Gear box kit 882524 1
18 Cone brake disc kit 880122 1
19 Brake cover kit 882525 1
20 Hawse fairlead 883410 1
21 Mounting hardware 880125 1
22 Remote control 880126 1
23 Handsaver strap 880026 1
24 Bridge Control box 12V 882685 1
24-1 Remote socket kit 12V 882718 1
24-2 Control pack 12V 882687 1
24-2-1 Central module kit 12V 882715 1
24-3 PC board kit 882716 1
24-4 Cutout switch 882693 1
24-5 Wireless transmitter 883822 1
25 Brake clutch base 881100 1
26 Motor side cover 882680 1
27 Sling hook 882477 1
Winch Assembly
2022/03/25 Ver:10