Come.up Winch SOLO 12.5rs User manual

Self-Recovery Winch
Model: SOLO 12.5rs
PN: 291202 12V DC
291285 12V DC
Introduction
Feature
Line pull: 5,670 kg / 12,500 lb synthetic rope first layer
Synthetic rope: 11mm × 25 m (7/16"×82′)
Brake: Patented cone brake holds full load
Clutch: Turn the T-handle for rapid rope payout
Control: Both handheld pendant switch and built-in digital
two ways wireless transmitter power the winch
Unpacking
．Winch assembly……………………………………………………...1 pc
．Control box……………………..………………….………………... 1 pc
．Remote control……………………………………………………….1 pc
．Synthetic rope with sling hook……………………………………. 1 pc
．Hawse fairlead………………………..………………………………1 pc
．1.8 m (6′) 2 gauge battery lead………………………..……………
1 pc
．Wireless transmitter………………………………………………… 1 pc
Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
Installation
Before using the winch, make sure all electrical components have no
corrosion or damaged; the environment should be
clear and dry.
Winch and hawse fairlead mountings
•It is very important that the winch will be mounted
on a flat and hard surface of mounting channel
in order to make sure the motor, drum and
gearbox housing are aligned correctly.
•Hawse fairlead does not mount to the winch directly.
•The synthetic rope shall be wound in an under-wound orientation only.
•Four (4) M10 x 1.50 pitch 10.9 grade with 63.8 N-m torque settings
(maximum) high tensile steel bolts must be used in order to sustain the
loads imposed on the winch mounting.
•Two (2) M10 x 1.50 pitch stainless steel bolts must be used for fastening the
hawse fairlead into the mounting channel.
Wiring Diagram
•Attach the ground lead firmly to the negative (–) battery terminal and power
lead to the positive (+) battery terminal. The voltage drop for the winch
motor must not exceed 10% of the nominal voltage of 12V DC.
Nut fastening for motor & contactor
1. Holding the lower nut on the stub and fastening the upper nut clockwise.
2. The torque setting for nut is 14 N-m/124 lb-in.
Warning
•The winch is not intended to be used in any manner for the movement or lifting
of personnel.
•The rated line pull shown is based on the first layer of rope on the drum.

•The rope winding on the drum shall remain 10 wraps from the drum to support
the rated load.
•
Manufacturer is not responsible for the results of misuse, misapplication, faulty
installation or abuse of synthetic rope in any way.
Parts List
Item No. Description Part No. Qty
1 Waterproof motor w/housing 12V 883882 1
2 Tie bar kit 883883 2
3 Motor coupling 880005 1
4 Drum bushing 880006 2
5 Drum kit 881521 1
6 Gearbox support rack 883906 1
7 Grounding lead 880009 1
8 Synthetic rope 883285 1
9 1st shaft 881523 1
10 3rd ring gear kit 883900 1
11 3rd stage carrier 881960 1
12 2nd stage carrier 881961 1
13 1st stage carrier 881962 1
14 1st & 2nd ring gear 881963 1
15 1st pinion 881964 1
16 Clutch kit 883885 1
17 Gear box kit 883901 1
18 Cone brake disc kit 880122 1
19 Brake cover kit 883892 1
20 Hawse fairlead 883410 1
21 Mounting hardware 880125 1
22 Remote control 883887 1
23 Handsaver strap 880026 1
24 Bridge Control box 12V 883888 1
24-1 Remote socket kit 12V 883889 1
24-2 Control pack 12V 883890 1
24-3 PC board kit 883891 1
24-4 On/Off switch kit 884091 1
24-5 Power lead 883893 1
24-6 Motor thermal connector 883894 1
24-7 Wireless transmitter 883822 1
25 Brake clutch base 881100 1
26 Sling hook 882477 1
Winch Assembly
2022/11/21 Ver:00