Come.up Winch Seal Slim 12.5 User manual

Model: Seal Slim 12.5
PN: 295042 12V DC
Introduction
Feature
Line pull: 5,670 kg / 12,500 lb wire rope first layer
Wire rope: 9.5 mm × 25 m (3/8"×82′) galvanized aircraft A7 × 19
Brake: Patented cone brake holds full load
Clutch: Turn the L-handle for rapid rope payout
Control: Handheld pendant switch powers the winch
Unpacking
．Winch assembly……………………………………………………....... 1 pc
．Control box…………………………………………............................. 1 pc
．Remote control………………………………………………………….. 1 pc
．Wire rope with Clevis hook…………………………………………….. 1 pc
．Roller fairlead…………………………………………………………….
1 pc
．1.8 m (6′) 2 gauge battery lead……………………………………….. 1 pc
Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
Installation
Before using the winch, make sure all electrical components have no
corrosion or damaged; the environment should be clear and dry.
Winch and roller fairlead mountings
It is very important that the winch will be
mounted on a flat and hard surface of
mounting channel in order to make sure the
motor, drum and gearbox housing are aligned
correctly.
Roller fairlead does not mount to the winch
directly.
The wire rope shall be wound in an under-wound
orientation only.
Four (4) M10 x 1.50 pitch 10.9 grade with 63.8 N-m torque settings
(maximum) high tensile steel bolts must be used in order to sustain the
loads imposed on the winch mounting.
Two (2) M12 x 1.75 pitch 8.8 grade with 76 N-m torque settings
(maximum) high tensile steel bolts must be used for fastening the roller
fairlead into the mounting channel.
Wiring Diagram
•Connect thermal sensor harness plug, control ground, and cable A/F1/F2 to
the motor.
•Attach the ground lead firmly to the negative (–) battery terminal and power
lead to the positive (+) battery terminal. The voltage drop for the winch
motor must not exceed 10% of the nominal voltage of 12V DC.
Nut fastening for motor & contactor
1.Holding the lower nut on the stub and fastening the upper nut clockwise.
2.The torque setting for nut is 14 N-m/124 lb-in.

Warning
．The winch is not intended to be used in any manner for the movement or lifting
of personnel.
．The rated line pull shown is based on the first layer of rope on the drum.
．The rope winding on the drum shall remain 5 wraps from the drum.
Parts List
Item No. Description Part No. Qty
1 Waterproof motor w/housing 12V 883576 1
2 Tie bar kit 883132 1
3 Motor coupling 880005 1
4 Drum bushing 880006 2
5 Drum kit 881521 1
6 Gearbox support rack 883578 1
7 Grounding lead 880009 1
8 Wire rope 881994 1
9 1st shaft 881523 1
10 3rd ring gear kit 883900 1
11 3rd stage carrier 881960 1
12 2nd stage carrier 881961 1
13 1st stage carrier 881962 1
14 1st & 2nd ring gear 881963 1
15 1st pinion 881964 1
16 Clutch kit 883236 1
17 Gear box kit 884307 1
18 Cone brake disc kit 880122 1
19 Brake clutch base 881100 1
20 Brake cover kit 882537 1
21 Mounting hardware 880024 1
22 Remote control 880126 1
23 Handsaver strap 880026 1
24 Control box 12V 881164 1
24-1 Remote socket kit 12V 881373 1
24-2 Control pack 12V 881400 1
25 Clevis hook 881996 1
26 Roller fairlead 880023 1
Winch Assembly
2023/11/20 Ver:02