Come.up Winch DV-6s User manual

Self-Recovery Winch
Model: D
V
-
6
s
PN: 854768 12V 854762 12V DC
854765 12V 854766 12V DC
Introduction
 Feature
Line pull: 2,722 kg / 6,000 lb wire rope first layer
Synthetic rope: 8 mm × 24.4 m (5/16" × 80
′
) synthetic rope
Brake: Patented cone brake holds full load
Clutch: Turn the
T
-handle for rapid wire rope payout
Control: Handheld pendant switch powers the winch
 Unpacking
．Winch assembl
y
………………………………………………………….. 1
p
c
．Control box w/ handle..…………………………………....................... 1
p
c
．Remote control…………………………………………………………… 1
p
c
．S
y
nthetic ro
p
e with clevis hook………….………………………………
1
p
c
．Hawse fairlead…………………………………………..……………….. 1
p
c
．2” rear recriver w/quick connector wiring kit…………..………………. 1 pc
 Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
 Information requesting or parts ordering
Please specify the followings information:
．Winch PN ．Serial number
．Part description ．Replacement part number
．Quantity for each part
Installation
Before using the winch, make sure all electrical components have no
corrosion or damaged; the environment should be clear and dry.
 Winch and hawse fairlead mountings
．
It is very important that the winch will be mounted on
a flat and hard surface of mounting channel in
order to make sure the motor, drum and gearbox
housing are aligned correctly.
．Hawse fairlead does not mount to winch directly.
．The synthetic rope shall be wound in an
under-wound orientation only.
．Four (4) M10 x 1.50 pitch 8.8 grade high tensile
steel bolts must be used in order to sustain the
loads imposed on the winch mounting.
．Two (2) M8 x 1.0 pitch 8.8 grade high tensile steel bolts must be used for
fastening the hawse fairlead into the mounting channel.
 Wiring Diagram
•Connect control ground, and cable A/F1/F2 to the motor.
•Attach the ground lead firmly to the negative (–) battery terminal and power
lead to the positive (+) battery terminal. The voltage drop for the winch
motor must not exceed 10% of the nominal voltage of 12V DC.
 Nut fastening for motor & contactor
1. Holding the lower nut on the stub and fastening the upper nut clockwise.
2. The torque setting for nut is 14 N-m/124 lb-in.

Warning
．The winch is not intended to be used in any manner for the movement or
lifting of personnel.
．The rated line pull shown is based on the first layer of rope on the drum.
．The rope winding on the drum shall remain 10 wraps from the drum.
Parts List
Item No. Description Part No. Qty
1 Motor 12V 881505 1
2 Tie bar kit 882256 2
3 Motor support rack 880077 1
4 Motor coupling 880078 1
5 Drum bushing 880006 1
6 Drum kit 880080 1
7 Drum bushing B 880081 1
8 Gearbox support rack 880082 1
9 Synthetic rope 883274 1
10 1st shaft 880084 1
11 Power lead 882252 1
12 3rd ring gear kit 880086 1
13 2nd stage carrier 880087 1
14 1st stage carrier 880088 1
15 Retaining ring 880089 1
16 1st & 2nd ring gear 880090 1
17 1st pinion kit 880091 1
18 Clutch kit 880092 1
19 Gear box kit 880093 1
20 Cone brake disc kit 880094 1
21 Brake clutch base 881099 1
22 Brake cover kit 880095 1
23 Hawse fairlead 882152 1
24 Mounting hardware 882370 1
25 Remote control 880025 1
26 Handsaver strap 880026 1
27 Control box 12V 882242 1
27-1 Remote socket kit 880029 1
27-2 Control pack 12V 882243 1
28 2” rear receiver 883713 1
29 Clevis hook 881995 1
Winch Assembly
2022/04/29 Ver.11