Come.up Winch Seal MadX 8.0s User manual

Self-Recovery Winch
Model: Seal MadX 8.0s
PN: 296090 12V DC 296065 12V DC
296061 12V DC
Introduction
Feature
Line pull: 3,630 kg / 8,000 lb synthetic rope first layer
Synthetic rope: 10 mm × 30.5 m (3/8"×100′) synthetic rope
Brake: Patented cone brake holds full load
Clutch: Turn the T-handle for rapid rope payout
Control: Handheld pendant switch powers the winch
Unpacking
．Winch assembly……………………………………..…………………… 1 pc
．Control box………………..................…………......……………........... 1 pc
．Remote control………………………………….……………………...... 1 pc
．Synthetic rope with sling hook…………………………………………. 1 pc
．Hawse fairlead………………………………….………………………… 1 pc
．1.8 m (6′) 2 gauge battery lead……………………...…………………. 1 pc
Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
Installation
Before using the winch, make sure all electrical components have no
corrosion or damaged; the environment should be clear and dry.
Winch and hawse fairlead mountings
．
It is very important that the winch will be mounted
on a flat and hard surface of mounting channel
in order to make sure the motor, drum and
gearbox housing are aligned correctly.
．Hawse fairlead does not mount to the winch
directly
．The synthetic rope shall be wound in an under-wound orientation only
．Four (4) M10 x 1.50 pitch 10.9 grade with 63.8 N-m torque settings
(Maximum) high tensile steel bolts must be used in order to sustain the
loads imposed on the winch mounting.
•Two (2) M10 x 1.50 pitch stainless steel bolts must be used for fastening the
hawse fairlead into the mounting channel.
Wiring Diagram
Attach the black lead firmly to the negative (–) battery terminal and red lead
to the positive (+) battery terminal. The voltage drop for the winch motor
must not exceed 10% of the nominal voltage of 12V DC.
Nut fastening for motor & contactor
1. Holding the lower nut on the stub and fastening the upper nut clockwise.
2. The torque setting for nut is 14 N-m/124 lb-in.
Warning
．The winch is not intended to be used in any manner for the movement or lifting
of personnel.
．The rated line pull shown is based on the first layer of rope on the drum.
．The rope winding on the drum shall remain 10 wraps from the drum to support
the rated load.
．Manufacturer is not responsible for the results of misuse, misapplication, faulty
installation or abuse of synthetic rope in any way.

Parts List
Item No. Description Part No. Qty
1 Waterproof motor w/housing 12V 883013 1
2 Forward tie bar kit 882521 1
3 Reverse tie bar kit 882522 1
4 Motor coupling 880005 1
5 Drum bushing 880006 2
6 Drumkit 881521 1
7 Gearbox support rack 882523 1
8 Grounding lead 880009 1
9 Synthetic rope 883248 1
10 1st shaft 880011 1
11 3rd ring gear kit 880114 1
12 3rd stage carrier 880115 1
13 2nd stage carrier 883015 1
14 1st stage carrier 883016 1
15 1st & 2nd ring gear 880118 1
16 1st pinion 883017 1
17 Clutch kit 881564 1
18 Gear box kit 882524 1
19 Cone brake disc kit 880122 1
20 Brake clutch base 881100 1
21 Brake cover kit 883018 1
22 Hawsefairlead 881061 1
Hawse fairlead (for 296065/296061) 883067 1
23 Mounting hardware 880024 1
24 Remote control 880126 1
25 Handsaver strap 880026 1
26 Control box 12V 881164 1
Control box 12V (for 296065/296061) 883070 1
26-1 Remote socket kit 12V 881373 1
26-2 Control pack 12V 881400 1
Control pack 12V (for 296065/296061) 883071 1
27 Sling hook 882477 1
28 Clamp 882160 2
Winch Assembly
2021/09/16 Ver:04