Comelit IPSWP06N01A User manual

SWITCH, 4 (PoE) + 2 GIGABIT PORTS
ART. IPSWP06N01A
Please read this manual thoroughly before use and keep it for future reference

- 1 -
Package contents
Check the contents of your package:
PoE switch x 1
User manual x1
Power supply x1
Power cord x 1
Accessories
If any part is lost and damaged, please contact your dealer.
Introduction
The device have 4 (PoE) +2 Fast uplink 10/100/1000Mbit/s RJ45 ports that increase the speed of your network server
and backbone connections, made Gigabit connection to a server or uplink a network.
The PoE ports automatically detect and power the IEEE 802.3af/at compliant Powered Devices (PD). Support QoS
(according to 1: 2: 4: 8 weight configuration), when the network is overloaded or congested. The power is transmitted
with the data in one single cable.
Hardware description
Front panel
The front panel consists of Ethernet RJ45 ports and the related leds.
Dip switch 1
Standard mode
Numbers 1-4 correspond to PoE port1 ~ port4.
In this mode there is a normal communication between the ports with auto-negotiation.
Extend mode
In this mode the PoE ports operate with auto-negotiation at 10Mbit/s speed in duplex mode only. The distance of PoE
power and network data can reach 200m.
Dip switch 2
Default: normal communication between the ports 1~6.
VLAN: 1-4 ports are divided into a single VLAN but can communicate with the ports 5-6.
Note: after changing the mode, there is no need to restart the device

- 2 -
LED indications
LED
Color
Function
Power
Orange
OFF: no power supply.
ON: power supply connected.
DATA
Green
OFF: no device connected to the corresponding port.
ON: the link through the port is successfully established at
10/100/1000Mbit/s.
Blink: the switch is sending or receiving data.
PoE
Orange
OFF: no PoE (PD) connected.
ON: PD successfully connected to the port.
Rear panel
DC: power supply input.
: connect to the ground to prevent lightning strike.
Installation
This part describes how to install the switch and make the connections. Please follow the instructions to avoid damages
and security problems.
Before cleaning the switch, unplug the power supply. Do not clean the switch with wet cloth or liquid
Do not place the switch near water or any damp area. Prevent water or moisture from entering into the chassis
Do not place the switch on an unstable place or desk. The switch might be damaged severely in case of fall
Ensure proper ventilation of the equipment and keep the ventilation vents free of obstructions
Make sure that the operating voltage is correct
Do not open the chassis while the switch is powered to avoid electrical shocks.
Desktop installation
Attach the rubber feet provided on the bottom at each corner. Allow adequate space for ventilation between the device
and the objects around it.

- 3 -
Wall-mounted installation
Fix the switch on the wall with 2 screws
Turn ON the switch
When powered, the switch start automatically, the led lights up as follows:
- the Power led lights up
- the data led blink for one second (represents the system reset)
Specifications
Supported standards
IEEE802.3, IEEE802.3u, IEEE802.3ab ,IEEE802.3az, IEEE802.3x,IEEE802.3af,
IEEE802.3at
Network cables
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e cable (≤100m)
MAC address table
4K, auto-learning, auto-aging
Transfer mode
Store-and-Forward
Frame forward rate
8.9Mpps
Switching capacity
12Gbit/s
Dimensions (L x H x D)
168 x 32 x 93mm
Fan
Fanless
PoE ports
1~4
PoE power on RJ45
Mode A: pin 1/2 (+), pin 3/6 (-)
Power supply
54.5VDC/32W (max)
PoE power budget
65W
Temperature
Operating: 0°C ~ 40 °C (32 °F ~104°F )
Storage: -40 °C ~ 70 °C (-40 °F ~158°F )
Humidity
Operating: 10% ~ 90% non-condensing
Storage: 5% ~ 90% non-condensing