Comelit IPSWP160A User manual

SWITCH, 16 POE GIGABIT
PORTS
ART. IPSWP160A
Please read this manual thoroughly before use and keep it for future reference

1
Table of Contents
1 Product Introduction ..................................................................................2
1.1 Product Overview ................................................................................2
1.2 Front and rear panel description..........................................................2
1.3 LED Indicator description.....................................................................3
1.4 Switch Features and Specifications.....................................................4
2 Hardware installation..................................................................................5
2.1 Power cord ..........................................................................................5
2.2 Connect Computer (NIC) to the switch................................................5
2.3 Switch Cascade Connection................................................................6
2.4 Switch connection to the PD................................................................6
2.5 RJ-45 Pin specification........................................................................6
2.6 Notes...................................................................................................7

2
1 Product Introduction
1.1 Product Overview
Thank you for choosing our company's switch, this product is a 16-port
10/100/1000M Unmanaged PoE Gigabit Ethernet switch.
The product is desktop design, all-metal chassis and elegant appearance. This
product is easy to install, can rack, plug and play, no management; dynamic
LED indicator to monitor switch status and troubleshooting work. Supporting
16 10/100/1000Mbps auto-negotiation ports, use store and forward technology,
combined with dynamic memory assignment, to ensure it can be distributed to
each port. Flow control ensures to prevent data packet from losing while
sending and receiving. Compatible with 10Base-T, 100Base-TX and1GBase
three network environment. Support IEEE802.3az energy efficient Ethernet
(EEE), reduce power consumption by detection cable length and operating
loading, auto adjust signal intensity, reduce energy consumption and protect
the environment.
LED panel light displays power and network state dynamically. All 16 ports
have PoE function, the power is up to 30 watts each port, compliant with
IEEE802.3af, IEEE802.3at standards. PoE total power reaches 260W for all
ports. It can connect IP phone, IP cameras, wireless LAN access point AP and
other PD devices, no need power cords and outlet socket.
1.2 Front and rear panel description
RJ45 port area on the front panel of switch:
It has 16 10/100/1000MAuto-Negotiation RJ45 ports (Auto MDI / MDIX) on the
front panel, it can connect to the LAN. Including a LINK /ACT/Speed LED each
port for port status indication, please read the table description for LED
function description.

3
Rear panel:
1.3 LED Indicator description
Switch indicators includes Link / Act/Speed, PoE, power status indicator. Link /
Act, PoE light is green, the power status indicator is red.
You can learn the switch work status by LED indicators. The following table
shows these indicators’ function:
LED
COLOR
STATUS
STATUS DESCRIPTION
Power
Red
On
Power ON
Off
Power OFF
Link/Act/Speed
Green/
orange
On
Connect to the port
10/100M: Orange
1000M: Green
Off
Disconnect to the port
Flashing
Sending or receiving data
PoE
Yellow
On
Detect the PD
Off
The PD is not connected to
or detected

4
1.4 Switch Features and Specifications
Features:
●Comply with IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE
802.3af ,IEEE802.3at standards
●Supports IEEE802.3x flow control for full-duplex mode and backpressure
for half-duplex transfer mode
●Support Storage - forward technology
●16 port 10/100/1000Mbps Auto -negotiation MDI/MDIX RJ45 ports
●Supports auto-negotiation function for UTP port, adjust the transmission
ways and the transmission speed automatically
●Supports MAC address auto-learning
●Dynamic LED indicator and provide a simple working status and
troubleshooting tips
●Supports a maximum power 30W each PoE port
Specifications:
Supporting standards and
protocols
IEEE802.3 10Base-T, IEEE802.3u 100Base-TX,
IEEE802.3af, IEEE802.3at
Network Media (Cable)
10Base-T: UTP category 3, 4, 5 cable (maximum 100m)
100Base-TX: UTP category 5, 5e cable (maximum 100m)
1000Base-TX: UTP category 5, 5e cable (maximum
100m)
Number of Ports
16 x 10/100/1000Mbps Auto-Negotiation RJ-45 ports
LED
indicator
10/100/1000M
Link/Act/speed
(10/100M indicator Orange; 1G indicator Green)
PoE
PoE
Power light
Power
Transfer Method
Store-and-Forward
Exchange capacity
32Gb/s
MAC Address Learning
Automatic learning, automatic aging, 8K MAC address
table
Packet filtering and forwarding
rate
10Mbps: 14880pps, 100Mbps: 148800pps; 1000Mbps:
1488000pps
Dimensions (W × D × H)
442 x 208 x 44 mm
Environment
Operating Temperature: 0℃- 40℃
Storage Temperature: -10℃- 70℃
Operating Humidity: 10%~90%RH Non-condensing
Storage Humidity: 5%~90% RH Non-condensing
Power
AC 100V ~ 240V; Frequency 50/60Hz

5
2 Hardware installation
Before installing the switch, make sure that the following "packing list" listed
OK. If any part is lost and damaged, please contact your local agent
immediately. In addition, make sure that you have the tools install switches and
cables by your hands.
One PoE Switch
One power cord
This User Guide
Rubber footpads
Mounting screws with two “L” planks
Note: This switch can be placed on a flat surface.
2.1 Power cord
Supports desktop and rack-mount installation, please follow below installation
tips:
Do not place heavy objects on the switch.
The equipment should be far from the power outlet about 1.5 meters.
Please check the power supply to ensure the connection safety carefully.
Make sure that leave sufficient ventilation around the devices, make the
switch work in a cool place.
Open the box, put the switch on the desk, please insert one side of power
regulator into AC outlet of switch, the other side will be insert into power
socket, if everything goes well, red "Power" indicators on the front panel
will be lighted, the other green light only flashes once.
2.2 Connect Computer (NIC) to the switch
Please insert the NIC into the computer, after installing network card driver,
please connect one end of the twisted pair to RJ-45 jack of your computer, the
other end will be connected to any RJ-45 port of switch, the distance between
switch and computer is around 100 meters. Once the connection is OK and the
devices are power ON normally, the green Link / ACT status indicator lights
corresponding ports of the switch.

6
2.3 Switch Cascade Connection
The any port of switch can automatically identify straight cable and cross cable,
so no matter which port can be cascaded.
Among switch, another switch, hub can be connected by many ways, either
connect any port of this switch to any port of another switch by straight cable or
you can also connect any port of one switch to any port of another switch by
unshield twisted pair RJ45, realize all switch cascade connection.
2.4 Switch connection to the PD
All 16 ports of switch have PoE power supply function, the maximum output
power up to 15.4W each port, it can make PD devices, such as internet phone,
network camera, wireless access point work, provide five levels of 3.84 ~
12.95W electric power request. You only need to connect the switch PoE port
directly to the PD port by network cable.
2.5 RJ-45 Pin specification
Please note the cable-making methods, because cable which does not meet
the standards of the sequence data will make the data transmission speed
slow, unstable and even be blocked, the following chart represents that the
standard RJ-45 jack and the connector and pin definition:
Standard RJ-45 jack / connector
RJ-45 connector pin definitions
Pin Number
Signal
1
A_TX + (Transmit）
2
A_TX - (Transmit)
3
B_RX + (Receive）
4
PoE Power-
5
PoE Power-

7
6
B_RX - (Receive）
7
PoE Power+
8
PoE Power+
2.6 Notes
Switch support auto-negotiation function, while connecting other network
devices, the port LED indicators status depends on the negotiation results of
the operation mode, please refer to previous page status indicator table. If the
connection is OK, but the indicator does not light, please try to check if other
network devices, network cable is OK.
Please put the switch on a stable, dry and cool place and prevent falling.
Make sure the switch work properly, please make sure if the power voltage
matches with the power requirements of switch before using.
While switch works, network cable port can be freely inserted or removed
without disrupting the work of the switch.
Before cleaning the switch, first unplug the power, and wipe with a damp
fabric, without liquid.
Please prevent the switch from dusty areas and strong electromagnetic
interference area.