Comelit IPSWP06N02A User manual

SWITCH, 4 (PoE) GIGABIT PORTS +
2 SFP SLOTS
ART. IPSWP06N02A
Please read this manual thoroughly before use and keep it for future reference

1
Package contents
Check the contents of your package
:

Switch x 1
User manual x 1
If any part is lost and damaged, please contact your dealer.
Introduction
The device have 4 (PoE) RJ45 ports + 2 SFP slots 10/100/1000Mbit/s. The PoE ports (1-4) automatically detect and
power the IEEE 802.3af/at compliant Powered Devices (PD). The power is transmitted with the data in one single cable.
This product is designed for severe industrial environment and support DIN rail installation. Port surge protection is up
to 6KV and the working temperature range is -40°C ~ 75 °C.
Product features
Surge protection: up to 6KV
Electrostatic protection: contact 8KV, air 10KV
Operating temperature: -40°C ~ 75 °C
Fanless, high energy metal heat conduction through the case
DIN rail installation
Industrial-scale components
MTBF: >100000 hours
Support IEEE802.3at and IEEE802.3af (PD) standard
Output power up to 32 W
Support IEEE802.3x full-duplex flow control and Backpressure half duplex flow control
Support IEEE 802.3az
Hardware description
Front Panel
The front panel consists of 4 x 10/100/1000Mbit/s Ethernet RJ45 Ports, 2 gigabit SFP slots and the related leds.
LED indications
LED
Color
Function
PWR
Green
OFF: no power supply.
ON: power supply connected.
LNK/ACT
Green
OFF: no device connected to the corresponding port.
ON: the link through the port is successfully established at
1000Mbit/s.
Blink: the switch is sending or receiving data.
Orange
OFF: no device connected to the corresponding port.

2
ON: the link through the port is successfully established at
10/100Mbit/s.
Blink: the switch is sending or receiving data.
PoE
Orange
OFF: no PoE (PD) connected.
ON: PD successfully connected to the port.
Blink: abnormal PoE supply.
Rear panel
The rear panel have the terminals to connect the DC power input (standard redundant power backup 5 pinhole
terminals).
Power input
In the rear panel there are 5 industrial power input terminals (48-57VDC) labeled V1-, V1+ (PWR1), V2- and V2+
(PWR2), 2 DC power inputs with redundant functions. They can be used alone or can be connected to two independent
DC power supply at the same time to avoid a power system failure and improves the network's reliability.
: connect to the ground to prevent lightning strike.
Installation
This part describes how to install the switch and make the connections. Please follow the instructions to avoid damages
and security problems.
Before cleaning the switch, unplug the power supply. Do not clean the switch with wet cloth or liquid
Do not place the switch near water or any damp area. Prevent water or moisture from entering into the chassis
Do not place the switch on an unstable place or desk. The switch might be damaged severely in case of fall
Ensure proper ventilation of the equipment and keep the ventilation vents free of obstructions
Make sure that the operating voltage is correct
Do not open the chassis while the switch is powered to avoid electrical shocks.
DIN-rail installation
Use the 45mm standard DIN rail type. This product has supplied installation fittings.

3
Turn ON the switch
When powered, the switch start and reset automatically
Specifications
Supported standards
IEEE802.3, IEEE802.3u, IEEE802.3az, IEEE802.3x, IEEE802.3af,
IEEE802.3at, IEEE 802.3ab, IEEE 802.3z
Network cables
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e, 5 cable（≤100m）
1000BASE-TX : Gigabit SFP optical RJ45 electrical module
1000BASE-SX : Gigabit SFP multimode (850nm, LC, DDM)
1000BASE-LX : Gigabit SFP mode (1310nm, LC, DDM)
1000BASE-ZX: Gigabit SFP single mode (1550nm, LC, DDM)
MAC address table
4K, auto-learning, auto-aging
Transfer mode
Store-and-Forward
Jumbo frame
9216 Byte
Packet buffer
1.5Mbit
Switching capacity
12Gbit/s
Frame forward rate
8.9Mpps
Power supply
48÷57VDC
Dimensions (L x H x D)
165 x 54 x 147mm
Fan
Fanless
PoE ports
1~4
PoE power on RJ45
Mode A: pin 1/2 (+), pin 3/6 (-)
PoE power budget
32W (max)
Temperature
Operating: -40°C ~ 75 °C (-40 °F ~167°F )
Storage: -40 °C ~ 80°C (-40 °F ~176°F )
Humidity
Operating: 10% ~ 90% non-condensing
Storage: 5% ~ 90% non-condensing
Surge protection
Differential mode: ±4KV, Common mode: ±6KV
MTBF
>100000 hours
Electrostatic protection
Contact: 8KV, air: 10KV