Comelit IPSWR030A User manual

1
REPEATER SWITCH,
3 POE GIGABIT PORTS
ART. IPSWR030A
Please read this manual thoroughly before use and keep it for future reference

2
Contents
1. Installation..................................................................................................3
2. Checklist.....................................................................................................3
3. Installation..................................................................................................4
3.1 Installation Method.......................................................................................................4
3.2 Desktop or Shelf Installation........................................................................................4
4. Powering on the Switch ............................................................................4
5. Powering on the Switch ............................................................................5
6. Network Connection..................................................................................5
7. Technical Specifications ...........................................................................6
Appendix: The standard RJ-45 Introduction ...............................................7

3
1. Installation
The is 3 ports Gigabit POE (Power over Ethernet) Repeater Ethernet switch, it full
compliance with IEEE802.3at standard, with one PD (Power Device) port; two PSE
(Power Source Equipment) ports. This switch can work through receiving power from
other PoE switch or equipment by PD port, the PSE port can supply power to other PD
equipment (the power is less than 30W), it achieve more flexible network applications like
this and it don't require external power adapter.
The switch provide you with a simple, economic, standard and high performance of
network application plan, it is ideal choice to promote the department and working group
performance. The switch provide simple and understood LED indicator light on the front
panel, so that you can quickly judge the working state of the switch, and help to diagnose
the network failure.
Features
Supports PoE IEEE802.3at compliant
Supports PoE IEEE802.3af compliant
support two Power Source Equipment to supply external devices
Supports IEEE802.3x flow control for Full-duplex Mode and backpressure for
Half-duplex Mode
Support ports Auto MDI/MDIX
8K entry MAC address table of the switch with auto-learning and auto-aging
LED indicators for monitoring PD, PSE, Link / Activity
No power supply
2. Checklist
Before you start installing your equipment, verify that the package contains the following:
The Gigabit POE Repeater Switch
This Users Manual
Please notify your supplier immediately if any of the mentioned items are missing or
damaged.

4
3. Installation
3.1 Installation Method
The site where you install the switch may greatly affect its performance. When installing,
please take the following consideration.
- Install the switch in a cool, dry place. See technical specifications for the acceptable
temperature and humidity operating ranges.
- Install the switch on a secure, level surface that can support its weight, at least 1Kg.
- Leave at least 10 cm of space at the front and rear of the switch to ensure adequate
ventilation.
3.2 Desktop or Shelf Installation
When installing the switch on a shelf on desktop please ensure guidelines are above are
following, including level surface and adequate ventilation.
4. Powering ON the Switch
The swtich is powered by your existing POE switch. No additional power supply is
required. Simply plug your cable from your POE switch into the PD port of the switch
and your switch will power ON and is ready to use.
Front Panel of the switch

5
5. Powering on the Switch
LED
Status
Description
PD (Orange)
ON
Switch has a connection from PD port to PSE
device. Power has been successfully applied.
OFF
Connection to PSE device is not present, no
power has been applied to the switch.
PSE (Orange)
ON
PD device such as IP Phone is connected to the
port and drawing power.
OFF
PD device is not connected, no power is being
drawn from the switch.
Link/Act
(Green)
ON
A valid link is established.
Blink
Traffic is present on port.
OFF
No link established.
6. Network Connection
Front panel of switch
Connect your devices (computer, router, switch, IP Phone, Wireless Access Point, IP
Camera etc.) to the ports with a CAT-5/CAT-5e/CAT-6 network cable. Since the switch
supports Auto MDI/MDI-X you can use either a straight through or cross-over network
cable.

6
Typical Installation of the switch
- Connect the switch from the PD port to your Gigabit POE Switch.
- Connect your IP device at the PSE port on the switch.
- Connect your Computer or other IP device to the PSE2 port on the switch.
7. Technical Specifications
Standards
IEEE802.3af, IEEE802.3x, IEEE802.3ab,
IEEE802.3az
Network cables
10BASE-T: UTP category 3, 4, 5 cable (maximum
100m)
100BASE-T: UTP category 5, 5e cable (maximum
100m)
1000BASE-T: UTP category 5e, 6 cable (maximum
100m)
Number of Ports
3 x 10/100/1000 Mbps Auto-Negotiation ports
LED
indicators
10/100/1000M
Link/Act
other
PD, PSE
Transfer method
Store-and-Forward
Switching Capacity
6Gb/s
MAC Address Learning
Automatically learning, automatically Update, 8K

7
Frame Filtering and Forward
Rate
148800pps
Environment
Operating Temperature: 0℃~40℃
Storage Temperature: -40℃~70℃
Operating Humidity: 10%~90% non-condensing
Storage humidity: 5%~90% non-condensing
Appendix: The standard RJ-45 Introduction
Please note cable-making methods, because cable which does not meet the
standards of the sequence data will make the data transmission speed slow,
unstable and even be blocked.
The following chart represents that the standard RJ-45 jack connector and pin
definition:
Standard RJ-45 jack / connector
RJ-45 connector pin definitions
Pin number
Signal
1
TX1 + (PoE Power+)
2
TX1 - (PoE Power+)
3
RX1 + (PoE Power-)
4
TX2 +
5
TX2 --
6
RX1 - (PoE Power-)
7
RX2 +
8
RX2 -

8
The standard cable, RJ-45 pin assignment
The following shows straight cable and crossover cable standard connection.
Please use straight cable to connect switch/hub or other devices:
Straight cable for the switch (uplink MDI-II port) to switch/hub or other devices connection
Cross over cable for switch (MDI-X port) to switch/hub or other network devices (MDI-X
port) connection.