Comelit IPSWP22N01A User manual

SWITCH, 16 (PoE) + 4 UPLINK
GIGABIT PORTS + 2 SFP SLOTS
ART. IPSWP22N01A
Please read this manual thoroughly before use and keep it for future reference

- 1 -
Package contents
Check the contents of your package:
PoE switch x 1
User manual x1
Power cord x 1
Accessories
If any part is lost and damaged, please contact your dealer.
Introduction
The device have 16 (PoE) + 4 Fast uplink 10/100/1000Mbit/s RJ45 ports + 2 SFP slots that increase the speed of your
network server and backbone connections, made Gigabit connection to a server or uplink a network.
The PoE ports automatically detect and power the IEEE 802.3af/at compliant Powered Devices (PD). The power is
transmitted with the data in one single cable.
Hardware description
Front panel
The front panel consists of Ethernet RJ45 ports and the related leds.
LED indications
LED
Color
Function
PWR
Green
OFF: no power supply.
ON: power supply connected.
LNK/ACT
Green
OFF: no device connected to the corresponding port.
ON: the link through the port is successfully established at
1000Mbit/s.
Blink: the switch is sending or receiving data.
Orange
OFF: no device connected to the corresponding port.
ON: the link through the port is successfully established at
10/100Mbit/s.
Blink: the switch is sending or receiving data.
PoE
Orange
OFF: no PoE (PD) connected.
ON: PD successfully connected to the port.
Blink: abnormal PoE supply.
DIPswitch
Default: normal communication between the ports 1~20.
VLAN: 1-16 ports are divided into a single VLAN but can communicate with the ports 17-20.
CCTV: extend the PoE distance up to 250m to expand your network.
Note: after changing the mode, You need to restart the device.

- 2 -
Rear panel
In the rear panel there is an AC inlet power socket, which accepts input from 100 to 240VAC, 50/60HZ.
Power socket
Connect the female connector of the power cord here and the male connector to the AC power outlet. Please make
sure that the voltage meets the requirement of the switch input voltage.
: connect to the ground to prevent lightning strike
Installation
This part describes how to install the switch and make the connections. Please follow the instructions to avoid damages
and security problems.
Before cleaning the switch, unplug the power supply. Do not clean the switch with wet cloth or liquid
Do not place the switch near water or any damp area. Prevent water or moisture from entering into the chassis
Do not place the switch on an unstable place or desk. The switch might be damaged severely in case of fall
Ensure proper ventilation of the equipment and keep the ventilation vents free of obstructions
Make sure that the operating voltage is correct
Do not open the chassis while the switch is powered to avoid electrical shocks
Desktop Installation
Attach the rubber feet provided on the bottom at each corner. Allow adequate space for ventilation between the device
and the objects around it.
Rack-mountable installation
The switch can be installed on an EIA 19-inch rack. Install the mounting brackets on the switch’s side panels (one on
each side), secure them with the included screws, and then use the screws provided with the rack to mount the switch
on the 19-inch rack.

- 3 -
Turn ON the switch
When powered, the switch start automatically, the led lights up.
Note: make sure that the voltage is correct before power ON, otherwise the switch will be damaged.
Specifications
Supported standards
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3x, IEEE802.3af,
IEEE802.3at
Network cables
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e cable (≤100m)
1000BASE-X: MMF or SMF SFP module
MAC address table
8K, auto-learning, auto-aging
Transfer mode
Store-and-Forward
Frame forward rate
10Base-T: 14881pps/port
100Base-TX: 148810pps/port
1000Base-T/X: 1488095pps/port
Switching capacity
40Gbit/s
Dimensions (L x H x D)
440 x 44 x 207mm
Fan
2
Power supply
100~240VAC, 50/60Hz
PoE ports
1~16
PoE power on RJ45
Mode A: pin 1/2 (+), pin 3/6 (-)
PoE power output
55VDC/32W (max)/port
PoE power budget
250W
Temperature
Operating: 0°C ~ 40 °C (32 °F ~104°F )
Storage: -40 °C ~ 70 °C (-40 °F ~158°F )
Humidity
Operating: 10% ~ 90% non-condensing
Storage: 5% ~ 90% non-condensing