Commend Duetto EE 980 User manual

VERSION 1.7/1217
MANUAL VERSION 1.7/1217
PRODUCT MANUAL
ENGLISH
This product manual refers to
firmware version 1.6

Control Station Duetto
21.7/1217
COMMEND INTERNATIONAL GMBH
Saalachstraße 51
A-5020 Salzburg – Austria
www.commend.com
Product manual Control Station Duetto
Edition December 2017
Version 1.7/1217
Legal notice
The manufacturer guarantees the functionality of its products as described in the datasheets and/or tech-
nical documentation. For error-free operation of the Intercom system, faultless transmission paths are
mandatory. The functionality of transmission paths, in particular of IP networks, exclusively is the respon-
sibility of the operating company of the transmission path and therefore the manufacturer can not be re-
sponsible in any manner, for errors and problems, which result from problems or malfunctioning of the
transmission path.
It is not allowed to copy any text of this document without permission of COMMEND INTERNATIONAL
GMBH.
The technical data contained herein has been provided solely for informational purposes and is not legally
binding. Subject to change, technical or otherwise. IoIP®, OpenDuplex ® and Commend®are trademarks
registered by Commend International GmbH. All other brands or product names are trademarks or regis-
tered trademarks of the respective owner and have not been specifically earmarked.
Attention
Mounting and installation of the control desk DUETTO and the equipment may be carried out by
authorised service personnel only. The device must only be opened by authorised service engineers. If the
device was opened by someone else, the warranty for the device becomes invalid.
Before opening the device, ESD precautions have to be observed.
Manufacturer’s reference
This equipment fulfils the requirements of the EU standard directive 2014/30/EU.
Therefore, this equipment is CE labelled.
Number of pages: 172

Control Station Duetto
1.7/1217 3
Content
General information 4
PDF format 4
Info boxes 4
Legend of requirements 4
Introduction 5
Features and highlights 5
Overview 6
Technical data 7
System requirements 8
Extent of supply 8
DUETTO series versions 8
Connections 9
Compatibility SIP PBX 10
Requirements for audio and video transmission 11
Supported external USB devices 12
Setup guide 13
First connection 14
IP Station Config configuration 14
CCT 800 configuration 16
WebConfig interface 19
Login 19
Overview 22
WebConfig configuration 24
System information 24
Configuration 29
Customization 68
Tasks 88
Shared administration 99
Program interface 103
General functions 103
Intercom functions 134
Control desk functions 142
Appendix 147
External video connection for Intercom and SIP contacts 147
Door opener function 150
Privacy SIP call 152
Import several contacts in the address book 153
Example: Configuration of a PIN code dialogue 155
Examples: Configuration of functions with logic tags 159
Safety and maintenance 164
Safety disclaimer 164
Cleaning instructions 164
Technical Support 165

General information Control Station Duetto
41.7/1217
General information
PDF format
Supported viewers
The PDF manual can be used with the following viewers:
Adobe Reader from version 6.0
Foxit Reader from version 5.0
Info boxes
Legend of requirements
In the left-hand margin, requirements for the respective features are displayed as follows:
ATTENTION
This information box addresses all necessary configuration options and actions which will allow an
error-free operation. Also, this box will warn you if a certain configuration, option or entered value
could lead to a malfunction of the application or a loss of data.
NOTE
This information box serves multiple purposes: It ranges from basic configuration tips to additional
advices and comments on occasional settings and events.
GOOD TO KNOW
This information box provides background knowledge which helps understand the basic principles
behind different configurations and the application itself.
Symbol Requirement
Required DUETTO firmware version
Required feature level of the subscriber card. 1)
No restart required. 2)
1) This information is only displayed if it is required for the respective feature. Feature levels can be expanded
with licenses. Further information about feature levels and licensing can be found in the manual “Intercom
Server Configuration”!
2) This information is only displayed if the configuration of the respective feature does not require a restart of
the Intercom Server with PRO 800 5.1 or higher. For further information, see manual “Intercom Server
Configuration”.
1.6

Control Station Duetto Introduction
1.7/1217 5
Introduction
The control desk DUETTO delivers full Intercom power in a compact form to offer users the double
benefit of advanced functions and great flexibility of use. It is designed to provide the user with an ideal
space-saving master Intercom station, either as desktop device or wall-mounted station.
Combining the best of IoIP@and SIP technology, DUETTO incorporates support of building automation,
as well as integrated video communication and surveillance. DUETTO serves a wide range of appli-
cation environments, from reception areas and porter’s offices to automated doors and gates, and
many more. Wherever video-supported visitor management is needed or if available space is low, but
the requirements are uncompromisingly high, DUETTO is the perfect solution.
Features and highlights
Compact control desk solution
High speech quality (transmission bandwidth up to 20 kHz)
7” TFT touch screen with IPS (In-Plane Switching)
Bi-directional video (can be hidden)
Optional with built-in HD video camera
Audio output over broadcasts with Real-time Transport Protocol (RTP)
SNMP support for surveillance of the DUETTO device
Applicable as desk and wall mount device
IoIP@and SIP support
OpenDuplex@for natural, hands-free communication with high volume
Modern user interface for intuitive control
Simple configuration via web interface
Digital inputs and outputs
Input recognition (e.g. line fault or buttons)
Secure connection with uploadable certificates
IPv4 and IPv6 support
IEEE 802.1X support (with EAP-TLS and EAP-MD5)
Authentication for external and internal cameras possible
Wi-Fi support
Housing manufactured from robust and high-quality polycarbonate
(IP rating IP20 acc. EN 60529)
Full headset and handset support (i.e. handling same as a phone)
Online functions (e.g. weather and time display)
Power supply via Power over Ethernet (PoE)

Introduction Control Station Duetto
61.7/1217
Overview
Features
DUETTO “Features”
Handset: Remains magnetically in position (handset separately available)
HD video camera: Only for EE 980CM and SIP-EE 980CM
Display: 7” TFT touch screen with IPS (In-Plane Switching)
Loudspeaker: For Hi-Fi audio quality up to 20 kHz
Gesture control: Wakes DUETTO contact-less from the idle state
Microphone array: With digital MEMS microphones
Status LED: Red – Intercom call, blue – SIP call, flashing white – missed call, cyan – All Call
Connectors
DUETTO “Connections”
USB 2.0 port
MicroSD card slot
Input / Output: RJ12 jack. An overview of the pin assignment can be found on page 9.
External power supply: Coaxial power jack
Network: RJ45 jack
Headset: 4P4C jack (headset separately available)
Handset: 4P4C jack (handset separately available)
Service connection

Control Station Duetto Introduction
1.7/1217 7
Technical data
In the following table, the technical data of all ”DUETTO series versions”is listed:
IP rating: IP20 (acc. EN 60529)
Microphone: 4 electret condenser microphones
polar pattern: omnidirectional
Loudspeaker: special membrane type for optimal sound quality, 8 Ω
Amplifier: 700 mW
Sound pressure level: max. 85 dB
Inputs: 2 inputs for floating contacts (RJ12 jack)
Outputs: 2 open drain outputs (RJ12 jack) 1)
Call indication: status LED
Display: 7” TFT touch screen
resolution: 800 x 480 pixels
16,777,216 colours
IPS (In-Plane Switching)
Camera:
(only EE 980CM and SIP-EE 980CM)
built-in HD video camera
3.1 mega pixel
resolution: 640x480 pixels
frame rate: 7.7 fps
Transmission bandwidth: up to 20 kHz
Operating temperature range: 0 °C to +50 °C (+32 °F to +122 °F)
Storage temperature range: 0 °C to +50 °C (+32 °F to +122 °F)
Relative humidity: up to 95%, non-condensing
Connections: RJ45 jack for Ethernet and PoE
3 USB 2.0 (Type A) for external devices 2)
(e.g. for wireless USB adapter see page 12 or
additional relay output see page 12)
Power supply: PoE: IEEE 802.3af Class 3
or external power supply (24 VDC, 700 mA;
power range: 22 – 30 VDC)
with coaxial power connector
(outer diameter: 5.5 mm, inner diameter: 2.1 mm)
Cabling: min. Cat. 5
IP protocols: IPv4, IPv6, TCP, UDP, HTTP, RTP,
RTCP, DHCP, RTSP, SIP, , SNMP, STUN
Data rate: 10/100MBit/s (Full/Half Duplex)
Codecs: audio: G.722, G.711 A-Law, G.711 µ-Law, Opus, Speex
video: H.264 Constrained Baseline, Motion JPEG
Memory extension: MicroSD card
Mounting: wall mount kit (EE SH9)
desk kit (EE DK9)
Dimensions (H x W x D): with desk kit: 142 x 270 x 70 mm (5.59 x 10.6 x 2.76 in)
with wall mount kit:138 x 270 x 38 mm (5.4 x 10.6 x 1.5 in)
Weight incl. package: approx. 1000 g (2.2 lbs)
Colour: black
Optional accessories: handset (EE HS9)
PoE injector (PA 15W POE)
USB output module (EB1A; see page 12)
headset (HS1)
headset cable (KAB-HS1-RJ)
1) For use of the output with inductive loads, a suppression (flyback) diode must be used in parallel with the load!
Otherwise, the output can be damaged!
2) Rated current per USB 2.0 port: max. 500 mA
Power budget of all USB 2.0 ports: 800 mA with 5 VDC
1.3

Introduction Control Station Duetto
81.7/1217
System requirements
Required hardware and software
Intercom software and card firmware
GE 800 (min. PRO 800 5.0) with G8-IP (min. 6.1) or G8-IP32 (min. 6.1)
GE 300 (min. PRO 800 5.0) with G8-IP (min. 6.1)
IS 300 (min. PRO 800 5.0)
VirtuoSIS (min. PRO 800 5.0)
Configuration software
CCT 800 (min. 5.0)
Supported languages
The following languages are supported for the user interface of the DUETTO device:
English
German
French
Polish
Russian
Spanish
Extent of supply
Control desk DUETTO
Short reference
DUETTO series versions
Version SIP Intercom Built-in HD video camera
EE 980  
EE 980CM   
SIP-EE 980 
SIP-EE 980CM  
1.4
1.4

Control Station Duetto Introduction
1.7/1217 9
Connections
Connection diagram (bottom view)
Network connection
Connect the Ethernet cable to the RJ45 jack “Network”.
Power supply
PoE (“Power over Ethernet”)
Power supply is provided via the Ethernet cable, which is connected to the RJ45 jack “Network”. If no
PoE is provided via this Ethernet cable, a PoE injector can be used (e.g. “PA 15W POE”).
External power supply
Connect a power supply unit (power range: 22 – 30 VDC, 700 mA) to the coaxial power jack “External
power supply” (outer diameter 5.5 mm, inner diameter 2.1 mm).
Inputs / outputs
Connect the cable to the RJ12 jack “Input / output”. Via this connection, up to two inputs and outputs
can be used (see page 35 and page 37).
Connector pin assignment and connection options of inputs and outputs
Connector pin assignment and connection options
Pin assignment of the RJ12 jack “Input / output”:
6: Input 1
5: Input 2
4: INGND (reference point for inputs)
3: OCGND (reference point for outputs)
2: Output 1
1: Output 2
Handset
USB 2.0
MicroSD card slot
Input / output
External power supply
USB 2.0
Network
Headset
USB 2.0
-
+

Introduction Control Station Duetto
10 1.7/1217
Use of internal reference: The inputs are designed for floating contacts (e.g. relay contacts, push
buttons or switches).
Use of external reference: External power supplies are used (0 – 24 VDC).
The outputs are designed as open drain outputs.
Handset
Connect the handset to the 4P4C jack “handset”. The audio settings can be configured via the Web-
Config (see page 32).
Headset
Connect the headset to the 4P4C jack “headset”. The audio settings can be configured via the Web-
Config (see page 32).
USB 2.0
The DUETTO device has three USB 2.0 ports. The USB ports can be deactivated/activated via the Web-
Config (see page 55).
Compatibility SIP PBX
Basically, the DUETTO device can be used with any SIP server. The following SIP server types have
been tested explicitly by Commend and therefore a proper functionality can be confirmed:
NOTE: Cable length
Max. cable length: 2 m
ATTENTION: Suppression diode required at inductive loads
For use of the output with inductive loads, a suppression (flyback) diode must be used in parallel to
the load (otherwise, the output can be damaged)!
Manufacturer 1) Type Version
Cisco Cisco Call Manager
Cisco Unified Communication Manager Version 9.x
3CX 3CX for Windows Version 12
Starface Starface free Version 5.8
FreeSWITCH FreeSWITCH Version 1.2.0
1) The listed products and company names are brand names or registered trademarks of their respective owners.

Control Station Duetto Introduction
1.7/1217 11
Requirements for audio and video transmission
The following tables show the required bit rates for audio and video transmission per direction:
Audio transmission for SIP
Video transmission for IoIP® (for video codecs MJPEG and HTTP)
Video transmission for SIP (for video codecs H.264 Constrained Baseline and RTP)
ATTENTION:
Under certain circumstances, the required bit rates for video transmission can be higher than the giv-
en values!
Video transmission applies only to the DUETTO series versions EE 980CM and SIP-EE 980CM!
Codec Sampelrate Bandwidth Bitrate
G.711 8 kHz 3.5 kHz 80 kBit/s
G.722 16 kHz 7 kHz 80 kBit/s
Opus 48 kHz 20 kHz <50 kBit/s
Opus 16 kHz 7 kHz <50 kBit/s
Speex 16 kHz 7 kHz <30 kBit/s
Speex 8 kHz 3.5 kHz <30 kBit/s
Format / resolution Bit rate
QVGA 1 MBit/s 1)
VGA 3 MBit/s 1)
1) Applies for a frame rate of 5 fps.
Format / resolution Bit rate
QVGA 0.8 MBit/s 2)
VGA 2 MBit/s 2)
2) Applies for a frame rate of 10 fps.

Introduction Control Station Duetto
12 1.7/1217
Supported external USB devices
Chip sets for connection with a Wi-Fi network
The following chip sets have been tested by Commend International GmbH to connect the DUETTO
device to a Wi-Fi network:
RT2800USB
RTL8192CU
RTL8192EU
The DUETTO device can be connected with a Wi-Fi network via the program interface (see page 116).
EB1A – USB output module with one relay output
The USB output module “EB1A” offers a floating, galvanically isolated output contact (normally open
contact) for the DUETTO device, e.g. for use with a door opener. The configuration of the USB output
module is carried out via the WebConfig (see page 37).
Technical data EB1A
System requirements
DUETTO device with firmware version 1.4 or higher
Extent of supply
USB output module
Short reference
NOTE: Supported wireless USB adapter
The chip sets RT2800USB, RTL8192CU and RTL8192EU are included in the wireless USB adapters
“TPLinkTLWN823N” and “TPLinkTLW723N”.
NOTE: Consider firmware version
Certain chip sets are not supported on devices running an older firmware version (see page 99).
IP rating: IP20 (acc. EN 60529)
Connection: USB 2.0 (Type A)
max. 20 mA at 5 V
Relay output: 2-pin spring terminal (normally open contact)
max. operation current: 1 A (up to 55 °C/131 °F;
from 55 °C/131 °F, the max. operation current
is reduced by 0.1 A per 10 °C)
max. operation voltage: 20 VAC/30 VDC
insulation voltage: 500 VAC
wire diameter: min. AWG 26, max. AWG 20
(min. Ø 0,4 mm, max. Ø 0,8 mm)
Operating temperature range: –40 °C to +70 °C (–40 °F to +158 °F)
Storage temperature range: –40 °C to +70 °C (–40 °F to +158 °F)
Relative humidity: up to 90%, non-condensing
NOTE: Further information
For further information about the USB output module “EB1A”, see data sheet “EB1A”.
1.3
1.5
1.4

Control Station Duetto Setup guide
1.7/1217 13
Setup guide
DUETTO can be configured either as a SIP or/and Intercom station (depends on the DUETTO series
version; see page 8). Before using DUETTO with all of its functions, there are several configuration
steps, which have to be made. On the following pages, you will find a detailed step-by-step setup guide
to configure DUETTO via IP Station Config, CCT 800, and WebConfig. See the following illustration for
a basic configuration of DUETTO as a SIP or/and Intercom station:
Setup guide
First connection
INTERCOM
IP Station Config configuration
CCT 800 configuration
Add control desk function
Use built-in HD video camera
Login
WebConfig interface
Configuration: NETWORK ETHERNET
Configuration: INTERCOM
Program interface
Intercom functions
WebConfig interface
Login
Configuration: NETWORK ETHERNET
Configuration: SIP
Program interface
SIP
General functions
Configuration: CAMERA SERVER
General functions
Configuration: CAMERA SERVER
Control desk functions

Setup guide Control Station Duetto
14 1.7/1217
First connection
Establish connection
DUETTO is configured ex-works for DHCP. If no DHCP server is available, DUETTO uses a link-local IP
address through which the WebConfig can be accessed:
In order to find out the IP address, tap on the settings button on the display of DUETTO, tap on
the information button in the appearing menu and tap on the arrow button to open the device in-
formation dialogue .
→Default IP address: 169.254.x.x
→Default subnet mask: 255.255.0.0
If DUETTO cannot be used in the local network (LAN) with the configured IP address, the following pro-
cedure is recommended:
Establish a connection between the computer and DUETTO via a hub or switch.
The PC has to be in the same subnet as DUETTO. An appropriate IP address of that subnet range has
to be allocated to the computer temporarily.
IP Station Config configuration
Depending on the respective functions to be enabled or used for DUETTO, some of the instructions
may not be relevant and can therefore be skipped. In the following, you will find a detailed step-by-
step setup guide to configure DUETTO as an Intercom station via IP Station Config. For further
information about in-depth configuration see the manuals “GE 300” or “GE 800”.
The program IP Station Config can only be used in local networks (LAN):
Before DUETTO is installed at the respective location, it has to be configured first in a local network.
The computer, which is used for configuration, does not have to belong to the same subnet as
DUETTO.
Configuration IP Station Config
In the header, click on the button Query stations to list all available IP subscribers within the net-
work.
Color: Click on this button to change the colour as identifier (e.g. to group DUETTO).
Online: Shows the online state of the DUETTO device (also if the device is not connected to an
Intercom Server).
(Optional) CallNo: In this field, the call number of the DUETTO device can be entered.
(Optional) Description: In this field, a description of the DUETTO device can be entered (e.g. the
device text configured in CCT 800).
Station: Shows the type of the DUETTO device.
ATTENTION: Use a unique IP address
When connecting DUETTO to the local network (LAN), it is essential to make sure that this IP
address does not already exist in the network!
ATTENTION: Only for Intercom function
This installation step is only required for devices that will be configured as Intercom stations!
NOTE: Configuration of the internal video camera
The internal video camera of the EE 980CM has to be configured in the WebConfig (see page 52).

Control Station Duetto Setup guide
1.7/1217 15
Version: Shows the currently installed version of the DUETTO device.
IP address: In this field, enter the IP address of the DUETTO device if the function “DHCP” is dis-
abled.
Subnet mask: In this field, enter the subnet mask of the DUETTO device if the function “DHCP” is
disabled.
Router-IP: In this field, enter the router IP address of the DUETTO device if the function “DHCP” is
disabled.
Card-IP: In this field, enter the IP address of the IP card, to which DUETTO is connected.
Port: In this field, the destination port number of the IP subscriber card can be changed.
→By default: 16400
MAC: Shows the MAC address of DUETTO (can be configured via CCT 800 or WebConfig).
DYN: Activate this checkbox to enable the dynamic registration.
DHCP: Activate this checkbox to automatically configure the IP settings via a DHCP server (except
the fields Card-IP and Port).
(Optional) Host name: In this field, a host name can be entered for the DUETTO device (visible in
the status bar of DUETTO).
VID: In this field, enter the VLAN ID, which DUETTO shall use inside the network.
Send the configuration to the Intercom Server
The configuration of the IP stations has to be sent to the Intercom Server. It is possible to send either
the configuration of all stations, only of modified stations or of all stations selected in the table to the
Intercom Server.
Configuration IP Station Config
In the drop-down list next to the button Write Settings, select one of the following upload options:
all: The entire configuration will be sent.
modified: The configuration will be sent only to modified subscribers.
selected: The configuration will be sent only to the selected subscribers.
Click on the button Write settings to send the configuration to the respective IP subscribers.
Export the configuration to the computer
It is possible to save the configuration of the IP Station Config on the connected computer. The
exported configuration file can be saved in several data types.
Configuration IP Station Config
Menu Station > Export Settings
Select the data type of the exported configuration file in the submenu:
to EXCEL: Save as XLS file.
to HTML: Save as HTML file.
to TXT: Save as TXT file.
NOTE: Update of the device firmware
The device firmware has to be updated in the WebConfig (see page 99).

Setup guide Control Station Duetto
16 1.7/1217
CCT 800 configuration
Depending on the respective functions to be enabled or used for DUETTO, some of the instructions
may not be relevant and can therefore be skipped.
Add control desk function
DUETTO has the same configuration procedure as a conventional IP station and it is recognised by
CCT 800 as such. For further information about in-depth configuration, see manual “Intercom Server
Configuration“.
Configuration CCT 800
Subscriber > Station Properties > IP terminals > tab Common
Terminal IP Address: In this field, enter the same IP address, which is configured in IP Station
Config or WebConfig for the DUETTO device.
Port no: In this field, enter the same port number, which is configured in IP Station Config or Web-
Config for the DUETTO device.
→By default: 16400
Dynamic registration: Activate this checkbox to enable the dynamic registration. The field MAC
address will be activated.
MAC address: In this field, the MAC address of DUETTO can be entered. The MAC address will be
configured automatically if the checkbox Dynamic registration is deactivated.
ATTENTION: Only for Intercom function
This installation step is only required for devices that will be configured as Intercom stations!
ATTENTION: DUETTO must be initialized when changing terminal port
When a new device type is connected to a subscriber Ethernet port in an Intercom system, this device
must be initialized manually in CCT 800. A migration of the device type is not supported. For further
information, see manual “Intercom Server Configuration”.
ATTENTION: Enter unique MAC address
In order to prevent interferences, make sure that an unique MAC address is entered!

Control Station Duetto Setup guide
1.7/1217 17
Use built-in HD video camera
CCT 800 detects the built-in HD video camera of EE 980CM and SIP-EE 980CM automatically as soon as
the device is registered. In contrast with conventional cameras, nearly all settings of the built-in HD vid-
eo camera are configured automatically. For further information about the registration of an external
camera, see manual “Video WS”.
Configuration CCT 800
Subscriber > Station Properties > Cameras > tab Camera
Camera no: In this field, enter a unique number for the built-in HD video camera.
(Optional) Camera description: In this field, an up to 14-characters-long text can be entered, which
will be used in CCT 800.
(Optional) Camera text: In this field, an up to 14-characters-long camera text can be entered, which
will be displayed on TFT displays/monitors during camera connection.
Subscriber > Station Properties > Cameras > tab Addressing
Card IP address: Shows the IP address of the IP subscriber card to which DUETTO is connected.
Terminal IP Address: Shows the IP address of DUETTO.
Camera IP Address: Shows the IP address of the built-in HD video camera (equal to the IP address
of DUETTO).
Camera Port no.: In this field, the port number can be changed.
→By default: 7742
(Optional) Videolink: In this field, the video stream URL can be changed.
→By default: 3.mjpg
ATTENTION: Camera number must not be “0”
The camera number must not be “0”. Otherwise, the video stream is not shown on the DUETTO
display!

Setup guide Control Station Duetto
18 1.7/1217
Add video connection of external IP camera
A video stream of an external IP camera can be allocated to the DUETTO device in CCT 800 (in addition
to the built-in HD video camera). This video stream can be shown e.g. permanently on the DUETTO
display via a background element.
Configuration CCT 800
Subscriber > Station Properties > Cameras > tab Camera
Right-click and select the Intercom Server to which the external camera shall be assigned via the
entry “Add external camera”.
Camera no: In this field, enter a unique number for the video stream.
Camera description: In this field, an up to 14 characters long text can be entered, which will be
(Optional) used in CCT 800.
Subscriber > Station Properties > Cameras > tab Addressing
Camera IP Address: In this field, enter the IP address of the external IP camera.
Camera Port no.: In this field, enter the desired port number (RTSP = “554”, HTTP = “80”).
(Optional) Username and Password: In these fields, the data for authentication can be entered (if
required).
Videolink: In this field, enter the video stream URL with the syntax “rtsp://<video stream URL>” or
“http://<video stream URL>” through which the video stream of the external IP camera can be re-
trieved. See the following example:
Video stream example
Subscriber > General > tab Naming
Camera No.: In this field, enter the camera number entered under Subscriber > Station Proper-
ties > Cameras > tab Camera for the external video stream.
NOTE: Supported transmission protocols and codecs
DUETTO supports the following transmission protocols and codecs:
Transmission protocol: HTTP, RTSP
Video codec: H.264 Constrained Baseline, MPEG-4
Audio codec: AAC, AC3 32kHz Mono
NOTE: Resolution for proper playback of video stream
In order to ensure a proper playback of the video stream, the resolution of the video file may not exceed
800 x 600 pixel.
ATTENTION: Camera number must not be “0”
The camera number must not be “0”. Otherwise, the video stream is not shown on the DUETTO
display!
NOTE: Further information
For further information about the configuration of external IP cameras via CCT 800, see manual
“Video WS”.

Control Station Duetto WebConfig interface
1.7/1217 19
WebConfig interface
The main configuration of DUETTO has to be carried out via the integrated WebConfig. Depending on
the respective functions to be enabled or used for DUETTO, some of the instructions might not be
relevant and therefore can be skipped. In the following, you will find a detailed step-by-step instruction
to configure DUETTO via the WebConfig.
Login
Enter the IP address of DUETTO (e.g. https://169.254.10.10:8080) in the address bar of a web browser
to open the WebConfig. Further information how to find out the IP address of DUETTO can be found
on page 14. It is recommended to use one of the following web browsers:
Mozilla Firefox min. version 35
Google Chrome min. version 40
Apple Safari min. version 5.0
After entering the IP address in the address bar, the following login dialogue appears:
WebConfig “login”
It is possible to log in to the WebConfig either as an admin or a user. It is not possible to create addi-
tional accounts.
Login as admin
For an overview of all available features as admin see page 20.
User name : Enter the user name “admin”.
Password : Enter the password of the admin account.
→By default: admin
Click on the button SIGN IN to log in to the WebConfig. After a successful login, the home page
of the WebConfig will appear (see page 22).
NOTE: User name cannot be changed
The user name of the admin cannot be changed.
NOTE: Change the password
It is recommended to change the default password for the admin (see page 100).

WebConfig interface Control Station Duetto
20 1.7/1217
Login as user
For an overview of all available features as user see page 20.
User name : Enter the user name “user”.
Password : Enter the password of the user account.
→By default: password
Click on the button SIGN IN to log in to the WebConfig. After a successful login, the home page
of the WebConfig will be indicated (see page 22).
Overview of access rights
The admin has the permission to access all features in the WebConfig. The following illustration shows
an overview of all available features for the admin:
Overview “admin login”
NOTE: User name cannot be changed
The user name of the user cannot be changed.
NOTE: Change the password
It is recommended to change the default password for the user (see page 100).