CommScope ETHERSEAL 1479563-2 User manual

Instruction Sheet
1 of 2
To obtain information on CommScope®products,
contact your local CommScope®account
representative, PartnerPRO™Network Partner
or visit our website at www.commscope.com
This product is covered by one or more U.S.patents
or their foreign equivalents. For patents, see
www.commscope.com /ProductPatent/ProductPatent.aspx
©2016 CommScope, Inc.
All Rights Reserved
408-8875
DEC. 2016 Rev E
RECEPTACLE KIT
DESCRIPTION
INSTRUCTION SHEET
1479563-2
SL Series Jack, Unshielded Twisted Pair Category 5e
408-8417
1479564-2
SL Series Jack , Shielded Category 5e
408-8602
1479565-2
SL Series Jack , Unshielded Twisted Pair Category 6
408-8417
1479566-2
SL Series Jack , Shielded Category 6
408-8417
1479599-2
In-Line Coupler , Unshielded Twisted Pair Category 5e
NA
1479600-2
In-Line Coupler , Shielded Category 5e
NA
1933589-2
AMP-TWIST 6S Jack
411-93007
Figure 1
Each kit consists of a receptacle and either an in-line coupler or jack (with strain relief or dust cover). A nut and
O-ring is included for installing the receptacle in a panel or faceplate. The SL series jack kit includes a shield.
See Figure 1.
NOTE
Dimensions in this instruction sheet are in metric units [with U.S. customary units in brackets]. Figures are not drawn to scale.
Reasons for re-issue of this instruction sheet are provided in Section 2, REVISION SUMMARY.
1. ASSEMBLY
1.1. Wire Preparation and Jack Termination
Prepare the wire and terminate the jack according to the instruction sheet listed in Figure 1.
NOTE
The jacks accepts 4-pair, twisted-pair cable having sizes 24 to 22 AWG solid conductors. The SL series jack also accepts
cable having sizes 26 to 24 AWG stranded conductors with a maximum conductor insulation diameter of 1.27 mm [.050 in.].
1.2. Panel or Faceplate Cutout
Cut the panel or faceplate according to Figure 2.
ETHERSEAL®Receptacle Kits
Receptacle
O-Ring
Nut
Shield
(Included with
SL Series Kit Only)
AMP-TWIST
6S Jack
SL Series
Jack
Dust Cover
Bend-Limiting
Strain Relief

408-8875
Rev E
2 of 2
Figure 2
1.3. Installation
1. Slide the O-ring over the threaded portion of the receptacle. See Figure 2.
2. Insert the threaded portion of the receptacle through the front of the panel or faceplate. Orient the
receptacle in the cutout so that the white arrow indicator on the front of the receptacle is facing up.
See Figure 2.
3. From the back of the panel or faceplate, thread the nut onto the threaded portion of the receptacle.
See Figure 2. Tighten the nut to a torque of 2.26 Nm [20 in.-lb].
4. Refer to Figure 3, and insert the jack or coupler into the receptacle as follows:
a. From the back of the receptacle, align the fixed latch of the jack or coupler with the white arrow
indicator of the receptacle.
b. Tilt the back of the jack or coupler up at a slight angle, and slide it into the opening of the
receptacle. Hook the fixed latch into the slot inside the receptacle.
c. Rotate the back of the jack or coupler down so that the movable latch deflects and locks into the
receptacle.
Figure 3
2. REVISION SUMMARY
Revisions to this instruction sheet include:
Rebranded to CommScope®
Nut
O-Ring
Back of
Faceplate (Ref)
White Arrow Indicator
of Receptacle
Recommended Panel or Faceplate Cutout
Installing Receptacle
Note: Not to Scale
25.65 mm
[1.010 in.]
⌀28.45 mm
⌀[1.120 in.]
White Arrow Indicator
of Receptacle
Front of Receptacle
Movable Latch
Jack (Ref)
Slot Inside of
Receptacle
Fixed Latch
Opening of
Receptacle
Fixed Latch
Movable Latch
Rotate
Jack