CommScope SD-4U-SPLICE PANEL User manual

LEFT REAR ENTRY RIGHT REAR ENTRY
PARTS LIST
Break Out Input and Output Cables as follows.
Break out the cables per the diagram below, fitting the sub-units with mesh tubing as indicated. Route each sub-unit “bundle” into either back corner of the panel
as shown in Step 3. Secure the mesh tubing with tie wraps and felt tape in the location shown.
Install Panel as follows: (a) mount panel on frame; (b) remove
ALL transportation screws and tape from panel; (c) mount input and
output cables on frame at adjacent location using cable clamp of
customer choice (order separately); see Step 2 breakout diagram.
CABLE MESH TUBING BARE FIBER
CABLE CLAMP (SEE STEP 1)
SD-4U-SPLICE PANEL
CABLE
CLAMP
TRANSPORTATION
SCREW
MESH
LEFT
REAR
ENTRY
EXAMPLE
Product Description
The SD-4U-Splice Panel is a 19-inch
rack-mount panel for terminating
and splicing Outside Plant (OSP)
cables or Infra Facility Cables (IFC).
Each panel accomodates 1728
fibers in 6 C-size splice trays.
Each splice tray holds
4 splice modules, providing
288 mass fusion splices
(12 fiber ribbon x 24 splices).
Accessories listed at right must
be ordered separately .
DESCRIPTION
SD-4U SPLICE PANEL
RACK SCREW
PARTS LIST
QUANTITY
1
4
BREAKOUT
1
TIE POINT ON PANEL
PHILLIPS #2 SCREWDRIVER
SNIPS
TIE WRAPS
CABLE CLAMP 1
15
PARTS LIST
DESCRIPTION
TOOLS REQUIRED
QUANTITY
PARTS LIST
DESCRIPTION
ACCESSORIES
QUANTITY
FOST-ACC-C-TRAY -RIBN-24
SPLICE TRAY
MESH TUBING 200 FT.
1
1
6
Sections shown
are diagrammatic,
not proportional.
NOTE:
3a
3b
3c
2
3
TIE
WRAP
FELT
TAPE
Install Cable as follows: (a) remove back cover (unscrew knob to
release it); (b) route cable bundles to the rear of the panel;
secure on cable mount using cable tie and felt tape; (c) bring bundles
forward to the panel front; (d) unpack splice tray and identify
components; (e) route bundles to splice tray for splicing on
nearby table; (f) splice as shown; see Note below.
3a
3b
BACK
COVER
PANEL
SIDE
WALLS
NOT
SHOWN
UNSCREW
KNOBS
TO RELEASE
26323-A
FELT
TAPE
TIE
WRAPS
SPLICE
MODULES
SPLICE
TRAY
WITH
COVER
NOTE: These steps give a pictorial
overview. For complete
instructions, refer
to CommScope
document provided
with splice tray.
3e
3f
3cFELT
TAPE
& TIE
WRAP
3d
FELT
TAPE
& TIE
WRAP
OVERHEAD VIEW
(ONE BUNDLE)
LEFT REAR
ENTRY
EXAMPLE
TIE
WRAP
FELT
TAPE
3b
Quick
Start
CommScope (logo) and CommScope are trademarks.
86064582 Rev A © 2018, CommScope, Inc. All Rights Reserved.
TC-96255-IP · Rev A · December 2018
BREAKOUT LENGTH
126 IN. (320.04 CM)
100 IN.
(254.0 CM)
26 IN.
(66.0 CM)
POSITIONAL
(ADDITIONAL MESH
LENGTH TO BREAKOUT)

6
Continue adding cables and splice trays as needed.
Install them within the splice panel as shown from bottom to top.
The panel holds 6 splice trays.
RED LATCH
SPLICE
TRAY
SPLICE
TRAY TOWER
RED
LATCH
Wind splice tray and attached bundles back into the panel,
looping the bundles within the panel as shown.
Position the splice tray as shown at a right angle to the bottom hinge on
the splice tray deck. Insert the leading edge of the splice tray into the
tower and then rotate the tray 90 degrees to place it flat onto the
bottom of the panel.
4
Install first loaded splice tray into panel.
5
NOTE: Press on the red latch to pull out the work tray on the
front of the panel as shown.
26805-A
NOTE: For clarity, splice trays are shown without fiber in these views.
Release red latch (see above) and
slide shelf with splice trays back
into panel. Dress cables in an
orderly manner. Close panel doors.
7
LEFT REAR ENTRY ROUTING
RIGHT REAR ENTRY ROUTING
© 2018, CommScope, Inc. All Rights Reserved.
TC-96255-IP · Rev A · December 2018 PRODUCT PATENTS: https://www.commscope.com/ProductPatent/ProductPatent.aspx PRODUCT INFORMATION AND TECHNICAL SUPPORT: http://www.commscope.com/SupportCenter