Concept2 BikeERG User manual

0817
ASSEMBLY INSTRUCTIONS
BikeErg weight: 58 lb (26 kg)
Space required for use (training area):
48 in x 60 in
(122 cm x 152 cm)
Contact Concept2 directly at
800.245.5676 (U.S. and Canada)
or visit us at: concept2.com
Questions? Comments? Problems?

2
BikeErg Assembly Instructions
1Lay out all parts as shown.
1. Box frame assembly
2. Crank arm with pedal
3. Rear leg with seat post and saddle
4. Handlebar assembly
5. Front leg with handlebar post
6. Performance Monitor 5 (PM5)
7. Rear foot
8. Front foot with casters
2Lay the box frame assembly on the floor and with the flywheel facing down. Route the monitor cable through the
notch as shown. Attach the front leg to the box frame assembly using four fasteners. Check that the monitor cable
is routed properly and not pinched. IMPORTANT: To assure that screws are properly aligned and threads are engaged,
please insert all screws by hand, and get them started, before tightening any screws. This practice should be done at
every step of assembly.
(2) 3/4” (1.9 cm)
PN 1201
(2) 3” (7.62 cm)
PN 1267
DETAIL A
SCALE 1 : 2
PN 2230
(16) 3/4” (1.9 cm)
PN 1201
with patch
(4) 3/4” (1.9 cm)
PN 1248
without patch
(2) 3” (1.9 cm)
PN 1267
3” (7.62 cm)
PN 1267
3/4” (1.9 cm)
PN 1201
12
3
8
7
4
6
5

3
0817
3
(4) 3/4” (1.9 cm)
PN 1201
Orient the box frame assembly with the front leg in its
upright position. Attach the front foot with casters or
put the Box Frame Assembly with front leg in its upright
position using four fasteners. Finger tighten each before
tightening fully.
4
(4) 3/4” (1.9 cm)
PN 1201
Attach the rear leg with seat post and saddle to the
rear foot using four fasteners. Finger tighten each
before tightening fully.
5
(4) 3/4” (1.9 cm)
PN 1201
Attach the rear leg with foot assembly to the box frame using
four fasteners (two fasteners per side). Finger tighten only. These
fasteners will be tightened fully in step 6.
6
(2) 3/4” (1.9 cm)
PN 1201
Insert two fasteners on the top tab of the rear leg and tighten fully.
Fully tighten fasteners attaching the rear leg with foot assembly to
the box frame inserted in step 5.
3” (7.62 cm)
PN 1267

4
BikeErg Assembly Instructions
7Insert the handlebar assembly into the handlebar post.
8Insert the PM5 into the handlebar stem. Do not
insert any fasteners at this point until step 10.
DETAIL A
SCALE 1 : 4
9Thread the monitor cable through the cable clip on the front leg.

5
0817
10
(4) 3/4” (1.9 cm)
PN 1248
Note: Be sure to use the four fasteners without patch.
Insert two fasteners through the monitor cable tab and into
the bottom of the handlebar stem as shown in photo A. Do not
tighten screws completely. Insert two fasteners into the top of the
handlebar stem as shown in photo B. Plug in the monitor cable to
the PM5 as shown in photo C. Tighten all fasteners.
11 Remove the preinstalled 1” fastener from the right crank
arm with pedal. Then, attach the crank arm with pedal using
the same 1” fastener. Tighten fully. After five hours of use,
check the fasteners on both crank arms and be sure they are
fully tightened. These fasteners MUST be fully tightened to
prevent the crank arms from coming loose.
(1) 1” (2.54 cm)
PN 1247
12 Tighten both adjustment knobs. Refer to the BikeErg
Product Manual for more information on handlebar and
seat adjustments.
The machine should be used on a stable, level surface.
The BikeErg should be approximately level. The rear foot
has leveling pads that can be adjusted as needed.
A.
B. C.
1
2