Conel UR5i v2 SL User manual

UMTS router UR5i v2
and UR5i v2 SL
USER’S GUIDE

USED SYMBOLS
Conel s.r.o., Sokolska 71, 562 04 Usti nad Orlici, Czech Republic
Manual issued in CZ, 12/15/2011
ii
Used symbols
Danger – important notice, which may have an influence on the user’s safety or the function
of the device.
Attention – notice on possible problems, which can arise in specific cases.
Information, notice – information, which contains useful advice or special interest.
GPL license
Source codes under GPL license are available free of charge by sending an email
Declared quality system
ISO 9001

CONTENTS
iii
Contents
1. Safety instruction 1
2. Product disposal instructions 2
3. Router description 3
4. Contents of package 4
5. Router design 5
5.1. Version 5
5.2. Delivery identification 5
5.3. Ordering code 6
5.3.1. Basic version 6
5.3.2. Full version 6
5.4. Basic dimensions plastic box 7
5.5. Basic dimensions metal box 7
5.6. Mechanical external dimensions and mounting recommendations 8
5.7. User interfaces (connectors) 10
5.7.1. Status indication 11
5.7.2. Power connector PWR 12
5.7.3. Antenna connector ANT and AUX 13
5.7.4. SIM card reader 14
5.7.5. Ethernet port 14
5.7.6. PORT1 16
5.7.7. PORT2 16
5.7.8. USB port 17
5.7.9. I/O port 18
5.7.10.Reset 19
6. First use 20
6.1. Connecting the router before first use 20
6.2. Start router 21
6.3. Router configuration 21
6.3.1. Configuration over web browser 21
6.3.2. Configuration over Telnet 21
7. Technical parameters 22
7.1. Technical parameters of router 22
7.2. Technical parameters of module 22
7.3. Technical parameters of processor 23
7.4. Technical parameters of I/O port 23
7.5. Technical parameters of expansion port 23
8. Recommended literature 24
9. Possible problems 24
10. FAQ 25
11. Customers support 27

IMAGE LIST
iv
Image list
Fig. 1: Contents of package 4
Fig. 2: Front panel UR5i v2B 5
Fig. 3: Front panel UR5i v2B SL 5
Fig. 4: Front panel UR5i v2F SL 5
Fig. 5: Front panel UR5i v2F SL 5
Fig. 6: Label UR5i v2B 5
Fig. 7: Label UR5i v2B SL 5
Fig. 8: Label UR5i v2F 6
Fig. 9: Label UR5i v2F SL 6
Fig. 10 Basic dimensions plastic box 7
Fig. 11: Basic dimensions metal box 7
Fig. 12: Space around the antenna 8
Fig. 13: Space around antenna for SL version 8
Fig. 14: Cable routing 9
Fig. 15: Cable routing for SL version 9
Fig. 16: Space in front connectors 9
Fig. 17: Space in front connectors SL version 9
Fig. 18: Front panel UR5i v2F 10
Fig. 19: Front panel UR5i v2F SL 10
Fig. 20: Power connector 12
Fig. 21: Connection of power supply connector 12
Fig. 22: Connection of power supply 12
Fig. 23: External antenna 13
Fig. 24: Connecting the antenna 13
Fig. 25: Ejected the SIM cart 14
Fig. 26: Ethernet connector 14
Fig. 27: Connection Ethernet cable 15
Fig. 28: Example of router connection 15
Fig. 29: Connection PORT1 cable 16
Fig. 30: Connection PORT2 cable 16
Fig. 31: USB connector 17
Fig. 32: Connection PLC to the router 17
Fig. 33: Connection flash memory to the router 17
Fig. 34: I/O connector 18
Fig. 35: Connection I/O cable 18
Fig. 36: Connection input and output of router 18
Fig. 37: Router reset 19
Fig. 38: Router connection 20

TABLE LIST
v
Table list
Table 1: Expansion port possibilities 4
Table 2: Router version 5
Table 3: Delivery identification 5
Table 4: Ordering code of basic version 6
Table 5: Ordering code of full version 6
Table 6: Front panel description 10
Table 7: Router status indication 11
Table 8: Connection of power connector 12
Table 9: Connection of Ethernet connector 14
Table 10: Connection of USB connector 17
Table 11: Connection of I/O port 18
Table 12: Description of reset and restart router 19
Table 13: Technical parameters of router 22
Table 14: Technical parameters of module 22
Table 15: Technical parameters of processor 23
Table 16: Technical parameters of I/O port 23

SAFETY INSTRUCTION
1
1. Safety instruction
Please, observe the following instructions:
•The router must be used in compliance with all applicable international and national laws
and in compliance with any special restrictions regulating the utilization of the router in
prescribed applications and environments.
•To prevent possible injury to health and damage to appliances and to ensure that all
the relevant provisions have been complied with, use only the original accessories.
Unauthorised modifications or utilization of accessories that have not been approved may
result in damage to the router and in a breach of applicable regulations. Unauthorized
modifications or utilization of accessories that have not been approved may result in the
termination of the validity of the guarantee.
•The router can not be opened.
•Caution! The SIM card could be swallowed by small children.
•It must not be exceeded by the maximum voltage 30V DC power connector on the router.
•Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture and high temperature.
•The router should not be used at petrol stations of flammable and explosive materials. We
remind the users of the duty to observe the restrictions concerning the utilization of radio
devices at petrol stations, in chemical plants, or in the course of blasting works in which
explosives are used.
•Switch off the router when travelling by plane. Utilization of the router in a plane may
endanger the operation of the plane or interfere with the mobile telephone network, and
may be unlawful. Failure to observe these instructions may result in the suspension or
cancellation of telephone services for the respective client, or, it may result in legal
sanctions; it may also result in both eventualities.
•When using the router in the close proximity of personal medical devices, such as cardiac
pacemakers or hearing aids, you must proceed with heightened caution.
•If it is in the proximity of TV sets, radio receivers and personal computers, the telephone
may cause interference.
•It is recommended that you should create an appropriate copy or backup
of all the important settings that are stored in the memory of the device.

PRODUCT DISPOSAL INSTRUCTIONS
2
2. Product disposal instructions
The WEEE (Waste Electrical and Electronic Equipment: 2002/96/EC) directive has
been introduced to ensure that electrical/electronic products are recycled using the best
available recovery techniques to minimize the impact on the environment. This product
contains high quality materials and components which can be recycled. At the end of it’s life
this product MUST NOT be mixed with other commercial waste for disposal. Check the terms
and conditions of your supplier for disposal information.

ROUTER DESCRIPTION
3
3. Router description
3G UMTS/HSPA router UR5i v2 is used to wirelessly connect various equipments and
devices via Ethernet interface 10/100 to the Internet or intranet. Thanks to high data transfer
speed of up to 21.1 Mbit/s (download) and upload speed up to 5.7 Mbit/s it is an ideal
wireless solution for traffic and security camera systems, individual computers, LAN
networks, automatic teller machines (ATM) and other self-service terminals, etc.
s a standard, this exceptionally fast 3G UR5i v2 wireless router is equipped with one
Ethernet 10/100, one USB Host port, one binary Input/output (I/O) port and one SIM card
To save and backup communication data a version with 2 x SIM cards is available. The wide
range of interface options of the 3G router further expands expansion Port1 and Port2 -
selected by the customer – for example Ethernet port 10/100, serial interface ports
RS232/RS485/RS422/MBUS or (I/O - CNT). Port2 may be equipped with serial interfaces
RS232/RS485/RS422/MBUS or (I/O - CNT). This 3G wireless router is supplied either
in a plastic or metal casing, based on the requirements of the customer.
Configuration is done via web interface protected by password. The 3G UMTS/HSPA+
router supports creation of VPN tunnels using technologies IPsec, OpenVPN and L2TP
to ensure safe communication. Web interface provides detail statistics about the 3G router
activities, signal strength, detailed log, etc. Cellular router supports functions: DHCP, NAT,
NAT-T, DynDNS, NTP, VRRP, control by SMS and many other function.
Other diagnostic functions ensuring continuous communication include automatic
inspection of PPP connection offering an automatic restart feature - in case of connection
losses, or hardware watchdog which monitors the status of the router. With the help
of a special window (start up script window) you may insert Linux scripts for various actions.
For some applications the key option to create several different configurations for one 3G
wireless router, the so-called profiles (maximum of 4), and the option to switch between them
(for example via SMS, binary input status, etc.) is essential. Cellular wireless routers
may automatically upgrade configuration and firmware from server. This allows mass
reconfiguration of many routers in one time.
For easy use additional software may be used - communication VPN server Digicluster
and software for router monitoring R-SeeNet.
Examples of possible applications
•mobile office
•fleet management
•security system
•telematic
•telemetric
•remote monitoring
•vending and dispatcher machines

ROUTER DESCRIPTION
4
4. Contents of package
Basic delivered set of router includes:
•router,
•power supply,
•crossover UTP cable,
•external antenna,
•clips for the DIN rail,
•installation CD containing
instructions,
•paper start guide.
Fig. 1: Contents of package
The router box and DIN mount are supplied in a metal case in the SL version of the router.
The router can also be supplied as expansion accessories:
•one or two expansion ports RS232, RS485/RS422, ETHERNET, M-BUS or CNT.
Separation columns for mounting expansion boards are included.
Module can be connected only as follows.
PORT1 RS232, RS485/422, ETHERNET, M-BUS, CNT
PORT2 RS232, RS485/422, M-BUS
Table 1: Expansion port possibilities

ROUTER DESCRIPTION
5
5. Router design
5.1. Version
Box SIM1 SIM2 I/O USB PORT1 PORT2 ETH
UR5i v2B set Plastic
UR5i v2B SL set Metal
UR5i v2F set Plastic
UR5i v2F SL set Metal
Table 2: Router version
Fig. 2: Front panel UR5i v2B
Fig. 3: Front panel UR5i v2B SL
Fig. 4: Front panel UR5i v2F SL
Fig. 5: Front panel UR5i v2F SL
5.2. Delivery identification
Trade name Type name Other
UR5i v2B UR-5i-v2 Basic version
UR5i v2B SL UR-5i-v2 Basic version in the metal box
UR5i v2F UR-5i-v2 Full version
UR5i v2F SL UR-5i-v2 Full version in the metal box
Table 3: Delivery identification
Fig. 6: Label UR5i v2B
Fig. 7: Label UR5i v2B SL

ROUTER DESCRIPTION
6
Fig. 8: Label UR5i v2F
Fig. 9: Label UR5i v2F SL
5.3. Ordering code
5.3.1. Basic version
Expansion port Ordering code
Version without expansion port UR5i v2B set
Version with expansion Ethernet port UR5i v2B set ETH
Version with expansion RS232 port UR5i v2B set RS232
Version with expansion RS485 port UR5i v2B set RS458
Version with expansion MBUS port UR5i v2B set MBUS
Version with expansion CNT port UR5i v2B set CNT
Table 4: Ordering code of basic version
5.3.2. Full version
Expansion port Possible participation Ordering code
Version without expansion port UR5i v2F set
Version with expansion Ethernet port PORT1 UR5i v2F ETH set
Version with expansion RS232 port PORT1 a PORT2 UR5i v2F RS232 set
Version with expansion RS485 port PORT1 a PORT2 UR5i v2F RS458 set
Version with expansion MBUS port PORT1 a PORT2 UR5i v2F MBUS set
Version with expansion CNT port PORT1 UR5i v2F CNT set
Table 5: Ordering code of full version
Second expansion port is written after first expansion port in the ordering code.
Example:
•Full version with Ethernet and RS232 port: UR5i v2F ETH RS232 set.
•Full version with Ethernet and RS232 port in metal cover:
UR5i v2F SL ETH RS232 set.

ROUTER DESCRIPTION
7
5.4. Basic dimensions plastic box
Fig. 10 Basic dimensions plastic box
5.5. Basic dimensions metal box
Fig. 11: Basic dimensions metal box

ROUTER DESCRIPTION
8
5.6. Mechanical external dimensions and mounting
recommendations
Mounting recommendations:
•possibility to be put on a work surface,
•DIN rail with clips CPD2 (Elpac clip SL for SL version) are included.
For the most of applications with a built-in router in a switch board it is possible
to recognize two kinds of environments:
•no public and industry environment of low voltage with high i
•public environment of low voltage without high interference. nterference,
For both of these environments it is possible to mount router to a switch board,
the following there is no need to have examination immunity or issues in connection with
EMC according to EN 60439-1 ed.2:00 + A1:04.
For compliance of EN 60439-1 ed.2:00 + A1:04 specification it is necessary
to observe next assembly of the router to the switch - board:
•for whip antennas we recommend to observe a distance of 6 cm from cables
and metal surfaces on every side according to the next picture due to the elimination
of interference, while using an external antenna except for the switch-board it is
necessary to fit a lightening conductor,
•before mounting a router on sheet-steel we recommend using an external antenna,
Fig. 12: Space around the antenna
Fig. 13: Space around antenna for SL version

ROUTER DESCRIPTION
9
•for every cables we recommend to bind the bunch according to the following picture,
we recommend for this use:
length of the bunch (combination of power supply and data cables) can
be maximum 1,5 m, if the length of data cables exceeds 1,5 m
or in the event of, the cable leads towards the switch - board, we
recommend installing over - voltage protectors (surge suppressors),
with data cables they mustn't carry cables with reticular tension
~ 230 V/50 Hz,
all signals to sensors must be twisted pairs
Fig. 14: Cable routing
Fig. 15: Cable routing for SL version
•sufficient space must be left before individual connectors for handling of cables
Fig. 16: Space in front connectors
Fig. 17: Space in front connectors SL version
•for correct function of the router we recommend to use in the switch-board earth-
bonding distribution frame for grounding of power supply of router, data cables and
antenna,

ROUTER DESCRIPTION
10
5.7. User interfaces (connectors)
On the front panel is located:
Label Connector Description
PWR 2-pin Connector for connection the power supply adapter.
ETH RJ45 Connector for connection into the local computer network.
PORT1 RJ45 Connector for connection equipment over RS232, RS458/422,
ETHERNET, M-BUS or CNT.
PORT2 RJ45 Connector for connection equipment over RS232, RS485/422 or
M-BUS (only FULL version).
ANT SMA Connector for connection main antenna.
AUX SMA Connector for connection diversity antenna.
USB USB-A Host Connector– for connection the devices with the router, USB supports
equipments with PL-2303 and FTDI USB/RS232 converter.
I/O 3-pin Connector for connection of the binary input and output.
SIM1 - Holder for first SIM card.
SIM2 - Holder for second SIM card (only FULL version).
Table 6: Front panel description
Fig. 18: Front panel UR5i v2F
Fig. 19: Front panel UR5i v2F SL

ROUTER DESCRIPTION
11
5.7.1. Status indication
About router status inform eight led indicators on the front panel and on every port are
two LED indicators, which inform about port status.
Label Color State Description
PWR Green Blinking
On Router is ready
Starting of the router
GSM Red Blinking Communication in progress
PPP Yellow
1 x flash per
second
2 x flash per
second
3x flash per
second
Signal strength is from –50 dBm to –69 dBm
Signal strength is from –70 dBm to –89 dBm
or difference between neighbours cells is exactly
3 dBm
Signal strength is from –90 dBm to –113 dBm
or difference between neighbours cells is smaller than
3 dBm
USR Yellow Function selected by user
OUT Green On Binary output active
IN Green On Binary input active
ETH Green On
Off Selected 100 Mbit/s
Selected 10 Mbit/s
ETH Yellow On
Blinking
Off
The network cable is connected
Data transmission
The network cable is not connected
PORT Green Description by port (viz. Technical specification of expansion port)
PORT Yellow Description by port (viz. Technical specification of expansion port)
SIM1 Yellow On SIM card 1 is active
SIM2 Yellow On SIM card 2 is active
Table 7: Router status indication
State indicate of PPP LED is updated every 10 seconds.

ROUTER DESCRIPTION
12
5.7.2. Power connector PWR
Panel socket 2-pin.
Pin
number Signal
mark Description
1 VCC (+) Positive pole of DC supply voltage (+10 to +30 VDC)
2 GND (-) Negative pole of DC supply voltage
Table 8: Connection of power connector
Fig. 20: Power connector
Power supply for router is required between +10 V to +30 V DC supply. Protection
against reversed polarity without signaling is built into the router.
The power consumption during receiving is 1W. The peak power consumption during
data sending is 5,5W. For correct operation it is necessary that the power source is
able to supply a peak current of 600mA.
Connector on the power cable connects into the power connector on the router head
and tightens locking screws. (See bellow picture)
Fig. 21: Connection of power supply connector
Circuit example:
Fig. 22: Connection of power supply
The positive pole VCC is marked by a red socket on the power.

ROUTER DESCRIPTION
13
5.7.3. Antenna connector ANT and AUX
The antenna is connected to the router using the SMA connector on the front panel.
The router can not operate without the main antenna connected labeled as ANT.
ANT connector used to connect the main antenna router. To connect the second
antenna for diversity income is used second connector AUX.
Example of antenna:
Fig. 23: External antenna
The antenna with the SMA connector. The antenna is connected to screw the antenna
connector SMA to SMA connector on the router head. (See figure below).
Fig. 24: Connecting the antenna
Diversity antenna improves wireless features of router in weak signal strength.

ROUTER DESCRIPTION
14
5.7.4. SIM card reader
The SIM card reader for 3 V and 1.8 V SIM cards is located on the front panel
of the router. To initiate the router into operation it is necessary to insert an activated SIM card
with unblocked PIN in the reader. The SIM cards might be of different adjusted APN (Access
Point Name).
Changing the SIM card:
Press the small yellow button to eject the reader holder. Insert the SIM card into
the reader holder and slide it in the reader. (See bellow picture)
Fig. 25: Ejected the SIM card
5.7.5. Ethernet port
Panel socket RJ45.
Pin
number Signal mark Description Data flow direction
1 TXD+ Transmit Data – positive pole Input/Output
2 TXD- Transmit Data – negative pole Input/Output
3 RXD+ Receive Data – positive pole Input/Output
4 --- ---
5 --- ---
6 RXD- Receive Data – negative pole Input/Output
7 --- ---
8 --- ---
Table 9: Connection of Ethernet connector
Fig. 26: Ethernet connector
ATTENTION! Port ETH is not POE (Power Over Ethernet) compatible!

ROUTER DESCRIPTION
15
Ethernet cable plug into the RJ45 connector labeled as ETH. (See bellow picture)
Fig. 27: Connection Ethernet cable
The ETH router connection:
Fig. 28: Example of router connection
Other manuals for UR5i v2 SL
2
Table of contents
Other Conel Network Router manuals

Conel
Conel UR5 v2 User manual

Conel
Conel LR77 v2 SL User manual

Conel
Conel CR10 v2 SL User manual

Conel
Conel LR77 v2 SL User manual

Conel
Conel LR77 v2 SL Instruction sheet

Conel
Conel UCR11 v2 SL User manual

Conel
Conel XR5i v2 User manual

Conel
Conel SPECTRE v3 LTE User manual

Conel
Conel UR5 User manual

Conel
Conel UR5i v2 SL User manual

Conel
Conel Bivias v2 User manual

Conel
Conel ER75i v2 SL User manual

Conel
Conel EDGE ER75i User manual

Conel
Conel UR5i a User manual

Conel
Conel EDGE ER75i User manual

Conel
Conel ER 75i SL User manual

Conel
Conel Bivias v2 User manual

Conel
Conel CR10 v2 SL User manual

Conel
Conel UR5 User manual

Conel
Conel ER75i v2 SL User manual