Conel UR5 User manual

UMTS router UR 5 and UR 5 SL
USER’S GUIDE
Declared system
ISO 9001:2009
WWW.INFOPULSAS.LT
[email protected]

OBSAH
2
Contents
1. Safety instruction 5
2. Description of the router 6
2.1. Introduction 6
2.2. UMTS technology 6
2.3. HSDPA technology (High Speed Download Packet Access) 7
2.4. Delivery Identification 7
2.5. Antenna Connection 8
2.6. SIM Card Reader 9
2.7. Power Supply 9
2.8. Technical parameters 10
2.9. Description of the individual components of the router 11
2.9.1. UMTS module 11
2.9.2. Control microcomputer 11
2.10. User interfaces (Connectors) 12
2.10.1. Connection of the PWR Supply Connector 14
2.10.2. Connection of the Port1 Connector – RS232 15
2.10.3. Connection of the Port1 Connector – RS485 16
2.10.4. Connection of the Port1 Connector – RS422 17
2.10.5. Connection of the Port1 Connector – M-BUSD 18
2.10.6. Connection of the Port1 Connector – CNT 19
2.10.7. Connection of the ETH Connector 20
2.10.8. Connection of the Connector USB 20
2.11. Technical specification of optional PORT1 21
2.12. Modem status indication 23
2.13. Putting into operation 23
2.14. Mechanical external dimensions and mounting recommendations 24
3. Expansion port mounting 28
3.1. Expansion port mounting for UR 5 28
3.2. Expansion port mounting for UR 5 SL 30
4. Changing the SIM cards 32
4.1. Changing the Second SIM card in the UR 5 router 32
4.2. Changing the second SIM card in the UR 5 SL router 34
5. Configuration setting over web browser 36
5.1. Network Status 36
5.2. DHCP Status 38
5.3. IPsec status 38
5.4. UMTS/GPRS Status 38
5.5. DynDNS status 39
5.6. System Log 39
5.7. LAN Configurationx 40
5.8. VRRP Configuration 45
5.9. UMTS/GPRS Configuration 46
5.10. Firewall Configuration 49
5.11. NAT Configuration 50
5.12. OpenVPN Tunnel Configuration 53
5.13. IPSec Tunnel Configuration 56
5.14. GRE Tunnels Configuration 58
5.15. L2TP Configuration 60

CONTENTS
3 - 3 - 2.8.2010
5.16. DynDNS Client Configuration 61
5.17. NTP Client Configuration 62
5.18. SNMP Configuration 62
5.19. SMS Configuration 64
5.20. Expansion Port Configuration 70
5.21. USB Port Configuration 71
5.22. Startup Script 72
5.23. Automatic update configuration 73
5.24. Change profile 73
5.25. Change password 74
5.26. Set real time clock 74
5.27. Set SMS service center address 74
5.28. Unlock SIM card 74
5.29. Send SMS 75
5.30. Backup Configuration 75
5.31. Restore Configuration 75
5.32. Update firmware 75
5.33. Reboot 76
5.34. Default settings 77
5.34.1. LAN Configuration 77
5.34.2. VRRP Configuration 77
5.34.3. Firewall Configuration 78
5.34.4. UMTS/GPRS Configuration 78
5.34.5. NAT Configuration 79
5.34.6. OpenVPN Tunnel Configuration 79
5.34.7. IPsec Tunnel Configuration 81
5.34.8. GRE Tunnels Configuration 82
5.34.9. L2TP Tunnel Configuration 82
5.34.10. DynDNS Configuration 82
5.34.11. NTP Configuration 83
5.34.12. SNMP Configuration 83
5.34.13. SMS Configuration 83
5.34.14. Expansion Port Configuration 84
5.34.15. USB Port Configuration 84
5.34.16. Startup script 84
5.34.17. Automatic update 85
6. Configuration setting over Telnet 86
7. Possible problems 87
8. Reference 87
9. FAQ 87
10. Customers support 88
11. Product disposal instructions 89
12. Guarantee Claim Guidelines 90
13. Guarantee certificate 93

CONTENTS
4 - 4 - 2.8.2010
Symbols used
Danger – important notice, which may have an influence on the user’s safety or the function
of the device.
Attention – notice on possible problems, which can arise in specific cases.
Information, notice – information, which contains useful advice or special interest.
GPL licence
Source codes under GPL licence are available free of charge by sending an email
to [email protected].
Conel s.r.o., Sokolska 71, 562 04 Usti nad Orlici, Czech Republic
Issue in CZ, 8/2/2010

SAFETY INSTRUCTION
5
1. Safety instruction
Please, observe the following instructions:
•The communication module must be used in compliance with all applicable international
and national laws and in compliance with any special restrictions regulating the utilization
of the communication module in prescribed applications and environments.
•To prevent possible injury to health and damage to appliances and to ensure that all
the relevant provisions have been complied with, use only the original accessories.
Unauthorised modifications or utilization of accessories that have not been approved may
result in damage to the communication module and in a breach of applicable regulations.
Unauthorized modifications or utilization of accessories that have not been approved may
result in the termination of the validity of the guarantee.
•The communication module must not be opened. Only the replacement of the SIM card is
permitted.
•Caution! The SIM card could be swallowed by small children.
•Voltage at the feed connector of the communication module must not be exceeded.
•Do not expose the communication module to extreme ambient conditions. Protect
the communication module against dust, moisture and high temperature.
•It is recommended that the communication module should not be used at petrol stations.
We remind the users of the duty to observe the restrictions concerning the utilization
of radio devices at petrol stations, in chemical plants, or in the course of blasting works
in which explosives are used.
•Switch off the communication module when travelling by plane. Utilization
of the communication module in a plane may endanger the operation of the plane
or interfere with the mobile telephone network, and may be unlawful. Failure to observe
these instructions may result in the suspension or cancellation of telephone services for
the respective client, or, it may result in legal sanctions; it may also result in both
eventualities.
•When using the communication module in the close proximity of personal medical devices,
such as cardiac pacemakers or hearing aids, you must proceed with heightened caution.
•If it is in the proximity of TV sets, radio receivers and personal computers, the telephone
may cause interference.
•It is recommended that you should create an appropriate copy or backup
of all the important settings that are stored in the memory of the device.

EXPANSION PORT MOUNTING
6
2. Description of the router
2.1. Introduction
The UMTS router is a compact electronic device based on the UMTS module which
enables data transfers using HSDPA/UMTS/EDGE/GPRS/GSM technologies.
Primarily, the router expands the capabilities of the UMTS module by the option
of connecting more PC’s by means of the built-in Ethernet interface. In addition, the firmware
of the router provides automatic establishment and maintenance
of HSDPA/UMTS/EDGE/GPRS PPP connection. By means of the integration of a DHCP
server it provides the user with simple installation and Internet access.
In addition, the router is equipped with a USB 1.1 Host interface which is designed only
for connection to a USB device.
By customer request it is possible to equip the router with the PORT1 module and extend
the function of the UMTS router about RS232, RS485/RS422, M-BUSD or CNT (I/O module).
The UMTS router has two versions. The first version is basic UR 5 and the second
version is UR 5 SL in the aluminum box.
Examples of Possible Applications
•mobile office
•fleet management
•security system
•telematic
•telemetric
•remote monitoring
•vending and dispatcher machines
2.2. UMTS technology
For radio terrestrial part UMTS (Universal Mobile Telecommunication System), which is
marked as UTRA (UMTS Terrestrial Radio Access), is warranted 155 MHz band in frequency
band about the 2 GHz. It is bands 1900–1980 MHz, 2010–2025 MHz and 2110–2170 MHz.
The UMTS system is based on code division of carried channels – use the access
method WCDMA (Wideband Code Division Multiple Access). WCDMA exploits direct spread
spectrum DS (Direct Spread). For transmission the UMTS network exploits two duplex
techniques – transmission modes FDD (Frequency Division Duplex), which is based
on separate frequency channels (i.e. uplink and downlink uses different channels) and TDD
(Time Division Duplex), which is based on separate time (i.e. uplink and downlink uses one
channel, in which both directions are changes in time).
UMTS network consists of three basic entities:
•Basic network CN (Core Network) – own core of network UMTS,
•network UTRAN (UMTS Terrestrial Radio Access Network) – the radio access
network,
•users part UE (User Equipment) – entity, which allows the user to access
the UMTS network.

EXPANSION PORT MOUNTING
7
2.3. HSDPA technology (High Speed Download Packet Access)
HSDPA is an improved and extended version of the UMTS-TDD. HSDPA is available
for both UMTS FDD and for UMTS TDD. HSDPA raises significantly bit rate for downlink. It is
attained on the programmer level. It doubles capacity on BTS (Base Transceiver Station),
which allows process of data and signals from more users at one time. HSDPA is based
on a few innovations of network architecture; thanks to this, it has lower latency, faster
reaction on channel change quality and processing of H-ARQ (Hybrid automatic repeat
request) on transmission repeat. Transport channel for HSDPA effectively uses available
frequencies, on which transmits data packets together. Afterwards these packets are divided
between individual users according to specific algorithms.
2.4. Delivery Identification
Specimen Label:
Trade name
Type name
Other
UR 5 UR-5 Basic version
UR 5 SL UR-5-SL Version in the aluminum box
Example of expansion port PORT1:
Trade name
Type name
Power supply
Expansion port RS232 XC-232 Internal power supply
Expansion port RS485-RS422 XC-485422 Internal/external power supply
Expansion port M-BUSD XC-MBUSD External power supply
Expansion port CNT XC-CNT Internal power supply

EXPANSION PORT MOUNTING
8
Basic delivered set of router includes:
•UMTS router,
•power supply,
•crossover UTP cable,
•external antenna,
•plastic clips for the DIN rail with fixing screws,
•installation CD containing instructions.
In addition to the basics it is possible to deliver:
•expansion port RS232, RS485/RS422, M-BUSD or CNT (separation columns are
in distribution),
•adapter for use of a second SIM card.
The router standard designed for:
•mounting to a panel using through holes (only UR 5 version),
•possibility to be put on a work surface,
•for mounting onto a DIN rail, the plastic clips are included.
2.5. Antenna Connection
The antenna is connected to the router using the FME connector on the back panel.
External antennas:

EXPANSION PORT MOUNTING
9
2.6. SIM Card Reader
The SIM card reader for 3 V and 1.8 V SIM cards is located on the front panel
of the router, there is possibility inside the router in case of adapter for the second SIM card.
To initiate the router into operation it is necessary to insert an activated SIM card with
unblocked PIN in the reader. The SIM cards might be of different adjusted APN (Access Point
Name).
2.7. Power Supply
The router requires +10 V DC to +30 V DC supply. Protection against reversed polarity
without signaling is built into the router.
The power consumption during receiving is 1W. The peak power consumption during
data sending is 3.5W. For correct operation it is necessary that the power source is able to
supply a peak current of 500mA.

EXPANSION PORT MOUNTING
10
2.8. Technical parameters
HSDPA/
UMTS
/EDGE/GPRS
modul
e
Complies with standards EN 301 511, v9.0.2,
EN 301 908-1&2, v2.2.1,
ETSI EN 301 489-1 V1.6.1,
EN 60950-1:06 ed.2
HSDPA parameters 3GPP rel. 5 standard
bitrate 3.6 Mbps/384 kbps
UE CAT. 1 to 6, 11, 12
Data compress 3GPP TS25.212
UMTS parameters W-CDMA FDD standard
PS bitrate – 384/384 kbps
CS bitrate – 64/64 kbps
GPRS parameters GPRS multislot class 10, CS 1 to 4
EGPRS multislot class 10, CS 1 to 4,
MCS 1 to 9
Transmit power Class 3 (+23dBm) for UMTS 2100MHz
Temperature range Function
Storage -30
o
C to +60
o
C
-40
o
C to +85
o
C
Protection Freely
In switch board IP20 IP56
Supply voltage 10 to 30 V DC
Consumption Reception
GPRS
UMTS/HSDPA
300 mW
to 3,5 W (GPRS transmission)
to 5,5 W (UMTS/HSDPA transmission)
Dimensions 30x90x102 mm (DIN 35mm)
Weight 150 g
Antenna connector FME – 50 Ohm
User interface ETH
USB
PORT1
Ethernet (10/100 Mbit/s)
USB 1.1 type A host
Optional RS232/RS485/M-BUSD
or inputs/outputs (I/O)

EXPANSION PORT MOUNTING
11
2.9. Description of the individual components of the router
2.9.1. UMTS module
The UMTS module is used for HSDPA/UMTS/EDGE/GPRS UMTS network wireless
communication. It is integrated in the printed circuit board. The slide-out SIM card reader is
accessible from the front panel. The FME antenna connector is accessible from the back
panel.
UMTS Module
•Communicates in UMTS band 2100MHz
•CS bitrate – 64/64 kbps
•PS bitrate – 384/384 kbps
•Supports W-CDMA FDD (Wideband - Code Division Multiple Access Frequency Division
Duplex) standard
2.9.2. Control microcomputer
The core of the router is a 32-bit microprocessor with 16 MB RAM, 4 MB FLASH
EEPROM, serial interface RS-232 and an Ethernet interface 10/100 Mbit/s.
The microcomputer is connected to the UMTS OEM module through the USB interface and
controls the communication via HSDPA/UMTS/EDGE/GPRS. Towards to the user it is
connected on the Ethernet interface.
The software is built on the uClinux operating system.
The router support services as like DHCP, NAT, GRE, IPsec tunnels, etc.
The modem settings are saved in the FLASH EEPROM memory. All modem
configurations can be done through a web interface (HTTP), which is protected by security
password.
Actual firmware version: 2.0.3 (26.5.2010)

EXPANSION PORT MOUNTING
12
2.10. User interfaces (Connectors)
On the front and back panel of router the following connectors are located:
•one RJ12 or MRT9 connector (PWR) – for connection of the power supply adapter,
•one RJ45 connector (ETH) – for connection into the local equipment,
•one RJ45 connector (optional PORT1) – for connection of the local any arrangement over
RS232, RS485/422, M-BUSD or CNT,
•one FME or SMA connector (ANT) – for connection of the antenna,
•one USB-A Host connector (USB) – for connection of the devices to the router, USB
supports equipments with PL-2303 and FTDI USB/RS232 converter.
Front panel UR 5
Rear panel UR 5

EXPANSION PORT MOUNTING
13
Front panel UR 5 SL
Rear panel UR 5 SL

EXPANSION PORT MOUNTING
14
2.10.1. Connection of the PWR Supply Connector
Panel socket RJ12.
Pin
number
Signal
mark Description
1 +UN Positive pole of DC supply voltage (10 to 30 V)
2 NC Signal not connected
3 NC Signal not connected
4 +UN Positive pole of DC supply voltage (10 to 30 V)
5 GND Negative pole of DC supply voltage
6 GND Negative pole of DC supply voltage
Circuit example:
•Panel socket MRT9.
Pin
number
Signal
mark Description
1 +UN Positive pole of DC supply voltage (+10 to +30 VDC)
2 GND Negative pole of DC supply voltage
Circuit example:
The positive pole +UN is marked by a red socket on the power supply.
Pin 1 – +UN
Pin 2 – GND
Router
DC
+
Pin 1 – +UN
Pin 2 – NC
Pin 3 – NC
Pin 4 – +UN
Pin 5 – GND
Pin 6
–
GND
Router
DC
+

EXPANSION PORT MOUNTING
15
2.10.2. Connection of the Port1 Connector – RS232
Panel socket RJ45 (RS232 – DCE – Data Communication Equipment).
Pin
number
Signal
mark Description Data flow direction
1 RTS Request To Send Input
2 CTS Clear To Send Output
3 DTR Data Terminal Ready Input
4 DSR Data Set Ready – connected to +4 V through
330 Ohm Output
5 GND GROUND – signal ground
6 RXD Receive Data Output
7 CD Carrier Detect Output
8 TXD Transmit Data Input
Circuit example:
The router connection to the PC:
• cable KD2 is connected to serial port PC (example COM1)
The router connection to equipment with full-value RS232 interface:
Router
ETH
PORT1
PWR
Cable KD-2
Router
ETH
PORT1
PWR
Cable KD-2
Pin 1 – RTS
Pin 2 – CTS
Pin 3 – DTR
Pin 4 – DSR
Pin 5 – GND
Pin 6 – RXD
Pin 7 – CD
Pin 8 – TXD
Router
Meter
GND
RXD
TXD

EXPANSION PORT MOUNTING
16
2.10.3. Connection of the Port1 Connector – RS485
Panel socket RJ45.
Pin
number
Signal
mark Description Data flow direction
1 GND Signal and supply ground
2 GND Signal and supply ground
3 TxRx- RS485 B (-) Input/Output
4 TxRx+ RS485 A (+) Input/Output
5 TxRx- RS485 B (-) Input/Output
6 TxRx+ RS485 A (+) Input/Output
7 +12 V EXT
External power supply
8 +12 V EXT
External power supply
ATTENTION! Power supply is selected on the expansion port RS485 by help
of a jumper, 2.11. If galvanic separation is required the converter must have an external
power supply.
Circuit example of the equipment with a router with data cable length less than 10 m:
Circuit example of the equipment with a router with data cable length more than 10 m:
With a RS485 data cable more than 10m it is necessary to use overvoltage protection
on the router side!

EXPANSION PORT MOUNTING
17
2.10.4. Connection of the Port1 Connector – RS422
Pin
number
Signal
mark Description Data flow direction
1 SGND Signal and power supply ground
2 SGND Signal and power supply ground
3 RxD-
Receive Data (-)
Output
4 RxD+
Receive Data (+)
Output
5 TxD-
Transmit Data (-)
Input
6 TxD+
Transmit Data (+)
Input
7 +12V EXT
External power supply
8 +12V EXT
External power supply
ATTENTION! Power supply is selected on the expansion port RS422 by help
of a jumper, 2.9. If galvanic separation is required the converter must have an external
power supply.
Circuit example of the equipment with router with data cable length less than 10 m:
Circuit example of the equipment with a router with data cable length more than 10 m:
With a RS422 data cable more than 10m it is necessary to use overvoltage protection
on the router side!

EXPANSION PORT MOUNTING
18
2.10.5. Connection of the Port1 Connector – M-BUSD
Panel socket RJ45.
Pin
number
Signal
mark Description Data flow direction
1 GND Signal and supply ground
2 GND Signal and supply ground
3 TxRx- M-BUS B (-) Input/Output
4 TxRx+ M-BUS A (+) Input/Output
5 TxRx- M-BUS B (-) Input/Output
6 TxRx+ M-BUS A (+) Input/Output
7 +12 V EXT
External power supply
8 +12 V EXT
External power supply
ATTENTION! External supply is for converter M-BUSD!
If galvanic separation is required the converter must have external power supply.
Circuit example of the equipment with a router with data cable length less than 10 m:
Circuit example of the equipment with a router with data cable length more than 10 m:
With a M-BUS data cable more than 10m it is necessary to use overvoltage protection
on the router side!

EXPANSION PORT MOUNTING
19
2.10.6. Connection of the Port1 Connector – CNT
Panel socket RJ45.
Pin
number Signal mark
Description Data flow direction
1 BIN1/CNT1
Binary input/counter input
Input
2 BIN2/CNT2
Binary input/counter input
Input
3 BIN3
Binary input
Input
4 BIN4
Binary input
Input
5 GND
Signal ground
6 OUT1
Binary output (open collector)
Output
7 AN1
Analogue input
Input
8 AN2
Analogue input
Input
The user interface CNT is for monitoring and processing of analogue and binary
signals and to control (settings) of binary signals. Available are 2 counter and 2 binary inputs
or 4 binary inputs, 2 analogue inputs and 1 binary output. The settings of binaries
and counter inputs by the help of firmware in which the single input and output is defined.
Typical connection of the router measuring circuits:
The router does not support to modify any signals of the CNT port, for example logical
functions.

EXPANSION PORT MOUNTING
20
2.10.7. Connection of the ETH Connector
Panel socket RJ45.
Pin
number Signal mark
Description Data flow direction
1 TXD+ Transmit Data – positive pole Input/Output
2 TXD- Transmit Data – negative pole Input/Output
3 RXD+ Receive Data – positive pole Input/Output
4 --- ---
5 --- ---
6 RXD- Receive Data – negative pole Input/Output
7 --- ---
8 --- ---
ATTENTION! Port ETH is not POE (Power Over Ethernet) compatible!
The ETH router connection:
2.10.8. Connection of the Connector USB
Panel socket USB-A.
Pin
number Signal mark
Description Data flow direction
1 VCC Positive pole of 5V DC supply voltage
2 USB data - USB data signal – negative pole Input/Output
3 USB data + USB data signal – positive pole Input/Output
4 GND Negative pole of DC supply voltage
The USB router connection:
Router
USB
ETH
PORT1
PWR
USB cable A-B
Router
USB
ETH
PORT1
PWR
UTP cable
Switch