Consew 28 User manual

OPERATING INSTRUCTIONS
MODEL
SEWING MACHINE
COIVSOLIDATED SEWING MACHIIVE
CONSEW
1115 BROADWAY, NEW YORK, N. Y. 10010 • [phone] • Cable: CONSOMACH NEW YORK
From the library of: Superior Sewing Machine & Supply LLC

OPERATING INSTRUCTIONS CONSEW MODEL 28
SETTING UP THE MACHINE
Carefully unpack machine from packing case and make sure that all small parts and
accessories are removed from packing material.
Wipe machine clean of protective grease and lubricate oil holes v/ith a good grade of
sewing macnine oil (see below).
CAPACITY AND SPEED
Maximum operating speed after a break-in period is 16000 stitches per minute depending,
of course, on the type of material being sewn, its thickness and that of the seams
being crossed.
To assure durability and trouble free operation, it is imperative that for the first
several weeks of operation the maximum speed is held to not more than 1200 RPM in order
to allow the parts to become properly broken in.
DIRECTION OF ROTATION
In operation,the handwheel of the machine always turns toward the operator. To avoid
tangled threads and jamming of the sewing hook, do not turn handwheel otherwise,
OILING
Do not operate the machine, even if only for testing, unless it has be n properly oiled
at every spot requiring lubrication. These^ots are the holes at the arm and bed of
the machine which are identified with red paint markers. In addition, place one or two
drops of oil at all places where oiepart of the machine is in movable contact with
another. Occasionally, also remove the face plate, remove the accumulated lint from
the mechanism and distribute oil thoroughly, but in small quantities to all moving parts.
Also awing back the arm top cover, located to the left of the handwheel, and lubricate
the bearing of the connecting rod on the main shaft. Turn machine head back on its
hinges and lubricate the left hand shuttle shaft bearing as well as the sliding block
connected to the crank at the right end of the shuttle shaft.
Oiling must be done at least twice daily when the machine is in continuous operation
to assure free running and durability of the operating parts.
NOTE: During the break-in period a new machine should be oiled more frequently.
NEEDLES
The machine uses needle style 29 x 3 (Cat. 3741) in sizes 9 through 24. Needle style
135 X 17 (cat. 3355) can likewise be employed. The size of the needle should be
determined by the size of the thread, which must pass freely through the eye of the needle.
From the library of: Superior Sewing Machine & Supply LLC

-2-
THREAD
Use only LEFT twist thread for the needle. For the bobbin either left or right twist
thread may be used.
SETTINS THE NEEDLE
Turn handwheel toward you until needle bar has reached its highest point. Loosen the
needle clamp screw> remove old needle and insert a new one into its place. Push needle
upward into needle clamp as far as it will go. Be sure long groove of needle is to the
left and the eye of the needle aligned with the arm of the machine. Be sure to tighten
needle clamp screw to prevent needle from slipping or turning.
THREADING THE NEEDLE
To thread the machine, follow the points in the order in which they are numbered.
(1) Pass the thread through the hole in the spool pin on top of the machine arm cover.
(2) From right to left through the top hole of the thread retainer with the three holes.
(3) From left to right through the bottom hole of this thread retainer.
(4) Down betwe.:n the tensions discs, with the thread running from right to left under
the tension controller stud.
(5) Over the hook of the thread take-up spring.
(6) Under the slack thread regulator.
(7) Up and from right to left through the hole in the end of the thread take-up lever.
(8) Down through the eyelet on the faceplate.
(9) Down through the eyelet on the needle bar thread guard.
(10)From left to right through the eye of the needle. Leave about 4 inches of thread
t hrough the eye of the needle.
THREAD TENSIONS
a. Correct Tension. For ordinary stitching, the bobbin and needle threads should be
locked in the center of the thickness of the material, as illustrated in A, Figure 1.
If the tension on the needle thread is too tight, or if that on the bobbin thread is
too loose, the needle thread will be straight along the upper surface of the material,
as illustrated in B, figure 1. If the tension of the bobbin thread is too tight, or if
that on the needle thread is too loose, the bobbin thread will be straight along the
under side of the material, as illustrated in C, figure 1. If both threads are too tight,
the material will be pUckered and drawn together by the stitches, and the threads will break,
Bobbin Thread Tension. The tension on the bobbin thread is regulated by the bobbin
case tension spring. To increase the tension, turn the screw to the right. To decrease the
tension, turn the screw to the left. When the tension on the bobbin thread has been properly
adjusted, it is seldom necessary to change it, because a correct stitch can usually be
obtained by varying the tension on the needle thread.
From the library of: Superior Sewing Machine & Supply LLC

A. Perfect stitch.
B. Tight needle thread tension.
C. Loose needle thread tension.
Figure 1. Effect of tension on stitch.
-3-
c. Needle Thread Tension. The tension on the needle thread is controlled by the tension
regulating thumb nut on the tension controller. To change the needle thread tension, proceed
as follows:
(1) Lower the presser foot so that it rests upon throat plate. The tension discs, if
correctly adjusted, will then be closed. The tension should be regulated only when the
presser foot Is down.
(2) To Increase the tension, turn the thumb not to the right. To decrease the tension,
turn the thumb nut to the left.
REMOVING BOBBIN
a. Turn the balance wheel toward you until the needle moves up to Its highest point.
b. Draw out the slide (view plate) in the bed of the machine.
c. Reach under the stand top. With the thumb and forefinger of the left hand, open the
latch on the bobbin case and, holding the bobbin case by the latch, lift It to the left
and out of the shuttle race.
d. As long as the latch Is held open, a sliding lug inside the bobbin case holds the
bobbin inside the case. When the bobbin case is turned open-side down, and the latch
is released, the bobbin will drop out. Do not try to force the bobbin out of the case while
the latch is open.
WINDING BOBBIN
To wind thread on bobbin, proceed as follows:
a. Place the bobbin on the bobbin winder spindle and push It on as far as It will go,
b. Pass the thread from the bobbin thread cone on the thread stand down through the
thread hole In the tension bracket and down between the bobbin winder tension discs.
c. Pull the thread from the lower side of the tension discs to the bobbin.
d. Pass the thread around the bottom side of the bobbin, wind the end of the thread
around the bobbin a few times, push the bobbin winder pulley over against the machine
belt by pressing on the stop latch thumb lever and see that the automatic stop latch
catches and ho 1^the pulley against the driving belt.
From the library of: Superior Sewing Machine & Supply LLC

e. The bobbin may be wound while the machine is stitching. H>.wever, if no fabric is
under the needle, see that the needle thread is pulled out of the eye of the needle and
lock the presserfoa: in the reaised position by raising the hand lifting lever. The
needle thread should be pulled from the needle to prevent its catching the bobbin thread
and balling up under the throat plate; and the presserfott should be raised to prevent
undue wear.
f. Run tbemeachine until thebobbin is full. If the bobbin winder is properly adjusted,
the automatic stop latch will operate and throw the bobbin winder pulley away from the
machine belt when the bobbin is full.
g. If the thread fails to wind evenly on the bobbin, or piles up on one side of the
bobbin, loosen the screw \sMch holds the tension bracket and move the bracket to the
right or left as required. Then tighten the screw.
THREADING BOBBIN CASE
a. Figure 2 shows the relative positions of the bobbin case, bobbin and thread when the
bobbin is put into the bobbin case. The thread should draw over the top of thebobbin and
from left to right just before the bobbin is slipped into the case.
I BOBBIN CASE
sTENSfON SCREW
tRread slot
Figure 2. Bobbin case with bobbin ready to be slipped in
b. To thread the bobbin case, hold it in the left hand, as shown in A, figure 3, the
slot in the edge being near the top, and place the bobbin in the case so that the thread
pulls over the top of the bobbin and away from you.
c. Pull the thread into the bobbin case thread slot, as in B, figure 3, draw the
thread down under the bobbin case tension spring and into the delivery eye at the end
of the tension spring, as in C.
From the library of: Superior Sewing Machine & Supply LLC

-5-
Figure 3, Thrgading Bobbin Case
REGULATING THE LENGTH OF STITCH
Upon the arm, facing the operator, Is a pivoted lever that is fastened in position by a
thiraib
screw, movable in a slot; to change the length of the stitch, have the needle bar
up, loosen the thumb screw and move the end of the lever down to make the stitch longer,
or up to make it shorter; then tighten the thumb screw,
TO BEGIN SEWING
With the left hand take hold of the needle thread, leaving it slack between the hand and
the needle, turn the balance wheel toward you until the needle moves down and up again
to its highest point, thus catching the shuttle thread; draw up the needle thread and the
shuttle thread with it through the hole in the throat plate, and lay both threads back
from you; then place the material beneath the presserfoot, lower the presserfoot and
commence to sew, turning the balance wheel over toward you.
PRESSERFOOT PRESSURE ADJUSTMENT
Pressure on the material is regulated by the thumb screw which forms the upper bearing of
the presser bar. This seldom requires changing for ordinary work.
KNEE LIFTER
The presserfoot can be raised by operating the knee lifter to the right. This knee lifter
connects with a knee lifting lever on the bottom of the head of the machine. A knee
lifting lever push rod runs up and behind the arm of the machine to the presserfoot.
HAND LIFTING LEVER
The presserfoot may also be lifted and locked in its raised position by raising the hand
lever to its highest position. After the presserfoot has been locked in its raised position,
it may be released by pressing the knee lifter to the right.
REMOVING WORK FROM MACHINE
Let the take-up lever rest at its highest point; raise the presserfoot and draw the fabric
back and tP the left and cut the threads close to the goods.
From the library of: Superior Sewing Machine & Supply LLC

NUMERICAL LISTING OF PARTS FOR CONSEW MODEL #28
2006 Thread take up cam
2007 Needle bar crank
2008 Thread take up crank
2009C Thread take up lever complete
2010 Needle bar
2011 Feed forked connection
2012C Feed regulating crank w/roller
2013 Feed regulating lever shaft
2014 Feed regulating lever
2015 Feed regulating lever clamp plate
2017 Feed bar socket joint
2018 Needle bar connecting stud
2019 Feed bar bell crank bracket
2020 Feed bar bell crank bracket set screw
2021 Lifting presser bar connecting link
2022 Feed bar guide bracket
2023 Lifting presser bar (hollow)
2024 Lifting presser bar spring
2025 Lifting presser bar spring pin
2026 Presser regulating thumb screw
2027 Lifting presser bar lifting bracket
2028 Lifting presser bar lifting bracket set screw
2029 Feed bar bell crank
2030 Feed bar bell crank gap screw washer
2031 Lifting presser bar connecting link cap screw
From the library of: Superior Sewing Machine & Supply LLC

2032
2033
2034
2035
2037
2038
2039
2040
2041
2042
2043
2044
2045
2046
2047C
2048
2049
2050
2051
2052
2053
2054
2055
2056
2057
CONSEW MODEL #28
Tension releasing lever
Feed bar socket joint cap plate
Peed bar guide bracket cap plate w/pin
Feed bar guide bracket slide block
Feed bar bell crank
Tension Releasing lever connecting extension
Tension releasing lever connection
Tension releasing lever connection screw
Tension releasing lever connection screw washer
Feed regulator lever segment
Feed regulator lever segment screw
Shuttle race upper spring screw
Shuttle race upper spring
Arm shaft bushing (front)
Race body complete
Arm shaft
Shuttle bobbin case position plate
Knee lifter lifting lever
Lifting presser bar lifter
Lifting presser bar lifter pin
Thread Guard (large)
Thread take up spring regulator (tension bushing)
Needle plate (medium hole)
Needle plate thread guard
Thread take up spring reg. spring
From the library of: Superior Sewing Machine & Supply LLC

CONSEW MODEL #28
2058 Feed reg. lever shaft set screw
2059C Face plate complete
2060 Pulley (hand wheel)
2061c Arm top cover complete
2062 Arm top cover screw
2063 Arm top cover washer
2064 Spool pin
2065 Spool pin washer
2066 Arm oil tube (long)
2067 Arm oil tube (short)
2068 Knee lifter lifting lever pin
2069 Face plate thread guard
2070 Face plate thread guard rivet
2080 Needle plate (large hole)
2081 Lifting presser foot )
)
2082 Feeding hinged presser foot)
3007 Arm shaft bushing (back)
3011 Thread take up cam screw (large)
3012 Thread take up cam screw (small)
3015 Thread take up lever hinge pin
3016 Thread lever counter screw
3028 Knee lifter lifting lever link
3029 Knee lifter lifting lever link hinge screw
3033 Tension releasing lever pin
3034 Crank connecting rod
From the library of: Superior Sewing Machine & Supply LLC

CONSEW MODEL #28
3036C Crank connecting rod hinge screw w/nut
3037 Oscillating rock shaft crank
3038 Oscillating rock shaft pipe
3039 Oscillating shaft crank
3040 Face plate set screw
3041 Lower shaft/
3042 Shuttle driver
3047 Bobbin case
3060 Knee lifter lifting bar
3065 Thread retainer
3066 Thread retainer set screw
3069 Tension screw stud
3070 Tension check spring
3071 Tension releasing disc
3073 Tension releasing pin
3076 Shuttle body (hook)
3077 Thread take up lever hinge pin set screw
6007 Lower shaft crank slide block
6011 Shuttle race back
6012 Shuttle race spring
6013 Shuttle race spring screw
6024 Feed lifting rocker shaft crank roller
6025 Feed lifting rocker shaft crank set screw
6031 Needle plate screw
6033 Slide plate
6034
Slide plate spring
From the library of: Superior Sewing Machine & Supply LLC