Converters.TV 15338 User manual

HDMI 4K2K 1x2 SD-HD Scaler
- ID# 15338
Operation Manual

Introduction
The 1 by 2 HDMI Scaler is designed to scale both 4K2K and non-4K2K
HDMI signal into 1080p and also, bypass 4K2K signal o t on to 4K2K
display. Allowing all types of HDMI so rce signal to be display on HDTV/
Monitor. With friendly and simple design which allows ser with direct
viewing on inp t resol tion and o tp t signal p to 2 sim ltaneo s HDMI.
The 1 by 2 HDMI Scaler is yo r best media between HD and Ultra HD
signal.
Features
•S pports HDMI 4K2K signal bypass
•S pports HDMI signal bypass
•Sim ltaneo s HDMI o tp ts
•Friendly and simple to se
pplications
•Ultra HDMI so rce displaying on standard LED TV/monitor
•Ultra HDMI so rce displaying on 4K2K TV/Panel
•Examining if display s pports 4K2K
•Examining if so rce s pports 4K2K
System
Requirements
Inp t so rce eq ipment s ch as DVD/Bl -ray(4K2K) player and o tp t
HDMI (4K2K) TV/display
Operation Controls
and Functions
Front Panel
1. HDMI OUT/SCALER: This slot is to connect with HDMI TV/display
for o tp t AV displaying with resol tion p to 1080p.
2. BYPASS: This slot is to connect with HDMI TV/display with or
witho t 4K2K specification for o tp t AV displaying according to
inp tso rce signal setting.

Input Source Scaler Output Bypass Output
1080p 1080P 1080P
4K2K 1080P 4K2K
Note: Displaying HDMI 4Kx2K contents, equivalent source signal and
HDMI ca le are required on BYPASS output connection.
3. HDMI IN: Connect from HDMI source equipment such as Blu-ray/DVD
player with or without 4K2K signal.
4. SERVICE 2: This slot is reserved for factory use only.
5. 4K2K / 1080P LED: These LED will illuminate according to input source
signal’s resolution when oth LED are illuminating it state the input source’s
signal does not elong to 4K2K/1080P@24.
6. DC 5V IN: Connect 5V DC power supply into the unit and connect the
adaptor to an AC outlet.
Back Panel
1. RS-232: This slot is reserve for factory use only.
2. SERVICE 1: This slot is reserve for factory use only.
3. POWER LED: This LED will illuminate when the device is connected
with power supply.
4. BYP SS 4K2K: This LED will illuminate when the input signal contains
with 4K2K resolution.
5. MENU: Press this utton to enter into OSD menu.
6. -/+: Press this utton to scroll down/up the menu selection. Press “-“ with
“ENTER” utton to switch SCALER output resolution to 720p instantly
or press “+” with “ENTER” utton to switch SCALER output resolution
to XGA instantly.
7. ENTER: Press this utton to enter or confirm the selection.

OSD Menu
1st Layer 2nd Layer 3rd Layer 4th Layer
Picture Setting Contrast
Brightness
Fine Tune Hue 0~100
Saturation 0~100
Sharpness 0~100
NR Off/High/
Middle/
Low
Exit
Colour Red 0~100
Green 0~100
Blue 0~100
Exit
Output Setting Size Full/Over Scan/Under
Scan/Letter
Box/Pan Scan/Best Fit
Resolution 640x480/60,800x600/60,1
024x768/60,1280x1024/6
0,1600x1200/60,1366x76
8/60,1680x1050/60,1920x
1200/60,1280x800/60,144
0x900/60,1400x1050/60,1
600x900/60,480i/480p/72
0p60/1080i60/1080p60/57
6i/576p/720p50/1080i50/1
080p50/
Native
Exit
OSD Setting H-Position 0~100
V-Position 0~100
Timer Out 5~100
Background 0~100
Display Info/On/Off
Exit
Factory Setting Reset Yes/No

Exit
Information Input ...x...
Output ...x...
Version x.xx
Exit
Connection Diagram

HDMI Supported Resolutions Input Output
640x480@60 √ √
640x480@72 √
640x480@75 √
720x480@60 √
720x480i@60 √
720x576i@50 √ √
720x576p@50 √ √
800x600@56 √
800x600@60 √ √
800x600@72 √
800x600@75 √
1024x768@60 √ √
1024x768@70 √
1024x768@75 √
1280x720@60 √
1280x720p@60 √
1280x800@60 √ √
1280x1024@60 √ √
1440x1050@60 √
1600x1200@60 √ √
1920x1080@60 √
1920x1080i@50 √ √
1920x1080i@60 √ √
[email protected] √ √
1920x1080p@24 √ √
1920x1080p@25 √ √
[email protected] √ √
1920x1080p@30 √ √
1920x1080p@50 √ √
1920x1080p@60 √ √
1920x1200@60(RB) √ √

Specifications
Video Frequency 300MHz/9G ps
Input Ports 1 x HDMI,
2 x USB (Service only),
1 x RS-232 (Service only)
Output Ports 2 x HDMI
HDMI Cable Distance In 15M, Out 15M@1080p/8 it, In 10M, Out
10M@1080p/12 it, In 5M, Out 10M@4K2K
Power Supply 5V / 2.6A DC (US/EU standards, CE/FCC/
UL certified)
ESD Protection Human ody model:
±8kV (air-gap discharge)
±4kV (contact discharge)
Dimensions 145(W) x 167(D) x 30 (H)
Weight(g) 488
Chassis Material Aluminum
Silkscreen Color Black
Operating Temperature 0°C~40°C / 32°F ~ 104°F
Storage Temperature -20°C~60°C / -4°F ~ 140°F
Relative Humidity 20 ~ 90% RH (non-condensing)
Power Consumption 7.7W